Parking Brake and Brake System Indicator (Red)

• Comes on for a few seconds when you set the power mode to ON, then goes off if the parking brake has been released.
• Comes on when the parking brake is applied and goes off when it is released.
• Comes on when the brake fluid level is low.
• Comes on if there is a problem with the brake system.
• The beeper sounds and the indicator comes on if you drive with the parking brake not fully released.

• Comes on while driving – Make sure the parking brake is released. Check the brake fluid level.

hat to do when the indicator comes on while driving

• Comes on along with the ABS indicator

Have your vehicle checked by a dealer.

If the Brake System Indicator (Red) Comes On

Brake System Indicator (Amber)

• Comes on for a few seconds when you set the power mode to ON, then goes off.
• Comes on if there is a problem with a system related to braking other than the conventional brake system.

• Comes on while driving – Have your vehicle checked by a dealer.
• With this indicator on, your vehicle still has normal braking ability.

Low Oil Pressure Indicator

• Comes on when you set the power mode to ON and goes off when the engine starts.
• Comes on when the engine oil pressure is low.

• Comes on while driving – Immediately stop in a safe place.

If the Low Oil Pressure Indicator Comes On

• Indicates the current gear selection.

Shifting 

—

Transmission System Indicator

• Blinks if the transmission system has a problem.

• Blinks while driving – Avoid sudden starts and acceleration and have your vehicle checked by a dealer immediately.

• Comes on when the manual sequential mode is applied.

Sequential Mode Operation

—

Malfunction Indicator Lamp

• Comes on when you set the power mode to ON and goes off either when the engine starts or after several seconds if the engine does not start. If “readiness codes” have not been set, it blinks five times before it goes off.
• Comes on if there is a problem with the emissions control system.
• Blinks when a misfire in the engine’s cylinders is detected.

• Readiness codes are part of the onboard diagnostics for the emissions control systems.

Testing of Readiness Codes

• Comes on while driving – Have your vehicle checked by a dealer.
• Blinks while driving – Stop in a safe place where there are no flammable objects. Stop the engine for 10 minutes or more, and wait for it to cool down. Then, take the vehicle to a dealer.

If the Malfunction Indicator Lamp

Comes On or Blinks

Charging System Indicator

• Comes on when you set the power mode to ON and goes off when the engine starts.
• Comes on when the battery is not charging.

If the Charging System Indicator Comes On

Seat Belt Reminder Indicator

• Comes on and the beeper sounds if you are not wearing a seat belt when you set the power mode to ON.
• If the front passenger is not wearing a seat belt, the indicator comes on a few seconds later.

Blinks while driving if either you and/ or the front passenger has not fastened a seat belt. The beeper sounds and the indicator blinks at regular intervals.

• The beeper stops and the indicator goes off when you and the front passenger fasten their seat belts.
• Stays on after you and/or the front passenger has fastened the seat belt(s)

– A detection error may have occurred in the sensor. Have your vehicle checked by a dealer.

Seat Belt Reminder

Low Fuel Indicator

• Comes on when the fuel reserve is running low (approximately 1.9 U.S. gal./7.5 Liter left).

Blinks if there is a problem with the fuel gauge.

• Comes on – Refuel your vehicle as soon as possible.

Blinks – Have your vehicle checked by a dealer.

Anti-lock Brake System (ABS) Indicator

• Comes on for a few seconds when you set the power mode to ON, then goes off.

If it comes on at any other time, there is a problem with the ABS.

• Stays on constantly – Have your vehicle checked by a dealer. With this indicator on, your vehicle still has normal braking ability but no anti-lock function.

anti-lock Brake System (ABS)

Supplemental Restraint System Indicator

• Comes on for a few seconds when you set the power mode to ON, then goes off.
• Comes on if a problem with any of the following is detected:
• Supplemental restraint system
• Side airbag system
• Side curtain airbag system

Seat belt tensioner

Electric Power Steering (EPS) System Indicator

• Comes on when you set the power mode to ON and goes off when the engine starts.

Comes on if there is a problem with the EPS system.

• Stays on constantly or does not come on at all – Have your vehicle checked by a dealer.

If the Electric Power Steering (EPS) System Indicator Comes On

Vehicle Stability AssistTM (VSA®) System Indicator

• Comes on for a few seconds when you set the power mode to ON, then goes off.
• Blinks when VSA® is active.

Comes on if there is a problem with the VSA® system or hill start assist system.

• Stays on constantly – Have your vehicle checked by a dealer.

Vehicle Stability AssistTM (VSA®), aka Electronic Stability Control (ESC), System 

Vehicle Stability AssistTM (VSA®) OFF Indicator

• Comes on for a few seconds when you set the power mode to ON, then goes off.

Comes on when you partially disable VSA®.

VSA® On and Off 

—

Low Tire Pressure/ TPMS Indicator

• Comes on for a few seconds when you set the power mode to ON.
• Comes on if the tire pressure of any of the tires becomes significantly low.

Blinks for about one minute, and then stays on if there is a problem with the TPMS, or when a compact spare tire* is temporarily installed.

• Comes on while driving – Stop in a safe place, check tire pressures, and inflate the tire(s) if necessary.

Blinks and remains on – Have your vehicle checked by a dealer. If the vehicle is fitted with a compact spare tire, get your regular tire repaired or replaced and put it back on your vehicle as soon as you can.

System Message Indicator

• Comes on for a few seconds when you set the power mode to ON, then goes off.

Comes on along with a beep when a problem is detected. A system message on the multi-information display appears at the same time.

• While the indicator is on, press the (information) button to see the message again.
• Refer to the Indicator information in this chapter when a system message appears on the multi-information display. Take the appropriate action for the message.

The multi-information display does not return to the normal screen unless the warning is canceled, or the button is pressed.

—

Turn Signal Indicators

• Blinks when you operate the turn signal lever.

Blink along with all turn signals when you press the hazard warning button.

• Does not blink or blink rapidly

Replacing Light Bulbs

—

—

—

Auto High-Beam

—

Lights On Indicator

—

—

—

Immobilizer System Indicator

• Comes on briefly when you set the power mode to ON, then goes off.

Comes on if the immobilizer system cannot recognize the key information.

• Blinks – You cannot start the engine. Set the power mode to VEHICLE OFF (LOCK), then select the ON mode again.
• Repeatedly blinks – The system may be malfunctioning. Have your vehicle checked by a dealer.

Do not attempt to alter this system or add other devices to it. Electrical problems can occur.

—

Security System Alarm Indicator

Security System Alarm

—

Keyless Access System Indicator

• Comes on for a few seconds when you set the power mode to ON, then goes off.

Comes on as soon as a problem is detected in the keyless access system or keyless starting system.

Road Departure Mitigation (RDM) Indicator

• Comes on for a few seconds when you change the power mode to ON, then goes off.

Comes on if there is a problem with the RDM system.

Comes on when the RDM system shuts itself off.

• Stays on – The temperature inside the camera is too high.

Use the climate control system to cool down the camera.

The system activates when the temperature inside the camera cools down.

Front Sensor Camera

• Stays on – The area around the camera is blocked by dirt, mud, etc. Stop your vehicle in a safe place, and wipe it off with a soft cloth.
• Have your vehicle checked by a dealer if the indicator and message come back on after you cleaned the area around the camera.

Front Sensor Camera

Adaptive Cruise Control (ACC) Indicator (Amber)

• Comes on for a few seconds when you set the power mode to ON, then goes off.

Comes on if there is a problem with ACC.

Adaptive Cruise Control (ACC) Indicator (Green)

• Comes on when you press the MAIN button.

• Comes on if anything covers the radar sensor cover and prevents the sensor from detecting a vehicle in front.
• May come on when driving in bad weather (rain, snow, fog, etc.)

ACC has been automatically canceled.

• The area around the radar sensor is blocked by dirt, mud, etc. Stop your vehicle in a safe place, and wipe it off with a soft cloth. The indicator may take some time to go off after the radar sensor is cleaned.
• Have your vehicle checked by a dealer if the

indicator does not go off even after you clean the sensor cover.

Radar Sensor

• Use the climate control system to cool down the camera.

Goes off – The camera has been cooled down and the system activates normally.

• Comes on when the area around the camera is blocked by dirt, mud, etc. Stop your vehicle in a safe place, and wipe it off with a soft cloth.

May come on when driving in bad weather (rain, snow, fog, etc.)

• Comes on for a few seconds when you set the power mode to ON, then goes off.

Comes on if there is a problem with the LKAS.

Lane Keeping Assist System (LKAS) Indicator (Green)

• Comes on when you press the MAIN button.

• Use the climate control system to cool down the camera.
• Goes off – The camera has been cooled down and the system activates normally.

Front Sensor Camera

• Comes on when the area around the camera is blocked by dirt, mud, etc. Stop your vehicle in a safe place, and wipe it off with a soft cloth.

May come on when driving in bad weather (rain, snow, fog, etc.)

Blind spot information System Indicator*

• Comes on for a few seconds when you change the power mode to ON, then goes off. Stays on while the blind spot information system is turned off.

Customized Features

• Comes on while driving – Remove the obstacle in the vicinity of the sensor.

Blind Spot Information System

Collision Mitigation Braking SystemTM (CMBSTM) Indicator

• Comes on for a few seconds when you change the power mode to ON, then goes off.
• Comes on when you deactivate the CMBSTM. A multi-information display message appears for five seconds. Comes on if there is a problem with the CMBSTM.

Collision Mitigation Braking SystemTM (CMBSTM)

Collision Mitigation Braking SystemTM (CMBSTM) Indicator

• Stays on – The area around the camera is blocked by dirt, mud, etc. Stop your vehicle in a safe place, and wipe it off with a soft cloth.

Front Sensor Camera

• The area around the radar sensor is blocked by dirt, mud, etc. Stop your vehicle in a safe place, and wipe it off with a soft cloth. An indicator may take some time to go off after the radar sensor is cleaned.
• Have your vehicle checked by a dealer if the indicator does not go off even after you clean the sensor cover.

Radar Sensor

• Stays on – The temperature inside the camera is too high. Use the climate control system to cool down the camera. The system activates when the temperature inside the camera cools down.

Front Sensor Camera