2024 ACURA Integra Indicators Guidelines | How to use

Parking Brake and Brake System Indicator (Red)

• Comes on when the parking brake is applied and goes off when it is released.

• The beeper sounds and the indicator comes on if you drive with the parking brake applied.
• Comes on for about 30 seconds when you apply the electric parking brake while the power mode is in ACCESSORY or VEHICLE OFF, then goes off.
• Stays on for about 30 seconds when you set the power mode to VEHICLE OFF while the electric parking brake is applied, then goes off.

• Comes on when the brake fluid level is low.

• Comes on while driving – Make sure the parking brake is released. Stop in a safe place and check the brake fluid level.

What to do when the indicator comes on while driving

Parking Brake and Brake System Indicator (Red)

• Comes on if there is a problem with the brake system.

• Comes on along with the Parking Brake and Brake System Indicator (amber) – Immediately stop in a safe place. Contact a dealer for repair. The brake pedal becomes harder to operate. Depress the pedal further than you normally do.

If the Brake System Indicator (Red) Comes On or Blinks at the Same Time When the Brake System Indicator (Amber) Comes On

All models

• Comes on along with the ABS indicator – Have your vehicle checked by a dealer.

If the Brake System Indicator (Red) Comes On or Blinks

• Blinks and the Parking Brake and Brake System Indicator (amber) come on at the same time – There is a problem with the electric parking brake system. The parking brake may not be set.

Avoid using the parking brake and have your vehicle checked by a dealer immediately.

If the Brake System Indicator (Red) Comes On or Blinks at the Same Time When the Brake System Indicator (Amber) Comes On

Parking Brake and Brake System Indicator (Amber)

• Comes on if there is a problem with a system related to braking other than the conventional brake system.

• Comes on while driving – Have your vehicle checked by a dealer.
• With this indicator on, your vehicle still has normal braking ability.

• Comes on if there is a problem with the electric parking brake system and/or the automatic brake hold system.

• Stays on constantly – Avoid using the parking brake and have your vehicle checked by a dealer immediately.

• Comes on when the automatic brake hold system is on.

Automatic Brake Hold

Automatic Brake Hold Indicator

• Comes on when the automatic brake hold is activated.

Automatic Brake Hold

Malfunction Indicator Lamp

• After you have set the power mode to ON, the vehicle performs system checks. However, if the readiness codes have not been set by that time, this indicator will blink five times and then go off.

• Readiness codes are part of the onboard diagnostics for the emissions control systems.

Testing of Readiness Codes

• Comes on if there is a problem with the emissions control systems.
• Blinks when a misfire in the engine’s cylinders is detected.

If the Malfunction Indicator Lamp Comes On or Blinks

Charging System Indicator

• Comes on when there is a problem with the charging system.

• Stop in a safe place and contact a dealer immediately.

Checking the Battery

If the Charging System Indicator Comes On

Shift Position Indicator*

• Indicates the current shift position.

Shifting 

• Comes on when the 7-speed manual shift mode is applied.

7-Speed Manual Shift Mode

• Blinks if the transmission system has a problem.

• Have your vehicle checked by a dealer immediately.

Gear Position Indicator*

• Indicates 1st to 6th gear position and (N.

• If you shift gears very slowly, a different gear position may be displayed for a moment.

shifting

• When the power mode is turned on, (N is not displayed until it is shifted into (R or 1st to 6th gear position.
• 1st to 6th gear positions are not displayed when the vehicle is stopped.
• The display can be turned ON/OFF in customized features in the audio/information screen.

Customized Features

Shift Up Indicator*

• Comes on when shifting up is recommended.

Shift Up/Down Indicators

Shift Up/Down Indicators

Seat Belt Reminder Indicator

• Blinks and the beeper sounds for a few seconds if you are not wearing a seat belt when you set the power mode to ON, then the indicator comes on.
• If the front passenger is not wearing a seat belt, the indicator comes on a few seconds later.
• Comes on for a while when the rear seat belt is unfastened while the power mode is ON.
• Blinks while driving if you and/or any passenger have not fastened a seat belt. The beeper sounds and the indicator blinks at regular intervals.

• The beeper stops and the indicator goes off when you and the passengers fasten their seat belts.
• Stays on after you and/or the passengers have fastened the seat belt(s) – A detection error may have occurred in the sensor. Have your vehicle checked by a dealer.

Seat Belt Reminder

Low Fuel Indicator

• Comes on when the fuel reserve is running low (approximately 1.8 U.S. gal/7.0 Liter left).

• Refuel your vehicle as soon as possible.

• Blinks if there is a problem with the fuel gauge.

• Have your vehicle checked by a dealer.

Anti-lock Brake System (ABS) Indicator

• Comes on if there is a problem with the ABS.

• Stays on constantly – Have your vehicle checked by a dealer. With this indicator on, your vehicle still has normal braking ability but no anti-lock function.

Anti-lock Brake System (ABS)

Supplemental Restraint System Indicator

• Comes on if a problem with any of the following is detected:
• Supplemental Restraint System
• Side airbag system
• Side curtain airbag system
• Seat belt tensioner

• Stays on constantly – Have your vehicle checked by a dealer.

Electric Power Steering (EPS) System Indicator

• Comes on if there is a problem with the EPS system.

• Stays on constantly – Have your vehicle checked by a dealer.
• Do not drive displays on the driver

information interface – Immediately stop in a safe place and contact a dealer.

If the Electric Power Steering (EPS) System Indicator Comes On

Vehicle Stability AssistTM (VSA®) System Indicator

• Blinks when VSA® is active.

• Comes on if there is a problem with the VSA® system, brake assist system, hill start assist system, starting assist brake function*, or agile handling assist.

• Stays on constantly – Have your vehicle checked by a dealer.

Vehicle Stability AssistTM (VSA®), aka Electronic Stability Control (ESC), System Brake Assist System  Hill start assist system Starting Assist Brake Function

Agile Handling Assist 

• Comes on if the VSA® system is deactivated temporarily after the battery has been disconnected, and then re-connected.

• Drive a short distance at more than 12 mph (20 km/h). The indicator should go off. If it does not, have your vehicle checked by a dealer.

• Comes on when you partially disable VSA®.

VSA® On and Off

Low Tire Pressure/ TPMS Indicator

• Comes on if the tire pressure of any of the tires becomes low.

• Comes on while driving – Stop in a safe place, check tire pressures, and inflate the tire(s) if necessary.

• Blinks for about one minute, and then stays on if there is a problem with the TPMS with Tire Fill Assist, or when a compact spare tire* is temporarily installed.

• Blinks and remains on – Have your vehicle checked by a dealer. If the vehicle is fitted with a compact spare tire*, get your regular tire repaired or replaced and put back on your vehicle as soon as you can.

• Blinks when you operate the turn signal lever.
• Blinks along with all turn signals when you press the hazard warning button.

• Do not blink or blink rapidly – Have your vehicle checked by a dealer.

• Comes on when the parking, tail, and other external lights are on.

• Comes on when the high-beam headlights are on.

• Comes on when all the operating conditions of the auto high-beam are met.

Auto High-Beam

• Comes on when the fog lights are on.

Fog Lights

System Message Indicator

• Comes on along with a beep when a problem is detected. A system message on the driver information interface appears at the same time.

• While the indicator is on, roll the right selector wheel to see the message again.

Switching the Display

• Refer to the Indicator information in this chapter when a system message appears on the driver information interface. Respond to the message accordingly.
• The driver information interface will not return to the normal screen unless the warning is canceled, or the right selector wheel is rolled.

• Comes on when you set the dynamic mode to NORMAL.

• Comes on when you set the dynamic mode to COMFORT.

SPORT

• Comes on when you set the dynamic mode to SPORT.

SPORT+

• Comes on when you set the dynamic mode to SPORT+.

INDIVIDUAL

Immobilizer System Indicator

• Blinks if the immobilizer system cannot recognize the key information.

• Blinks – You cannot start the engine. Set the power mode to VEHICLE OFF, then select the ON mode again.

Canadian models

Depress and hold the brake pedal before setting the power mode to ON.

• Repeatedly blinks – The system may be malfunctioning. Have your vehicle checked by a dealer.
• Do not attempt to alter this system or add other devices to it. Electrical problems can occur.

Security System Alarm Indicator

• Blinks when the security system alarm has been set.

Security System Alarm

Auto Idle Stop OFF
Indicator*

• Comes on when the Auto Idle Stop system has been turned off by the Auto Idle Stop OFF button.

Auto Idle Stop System ON/OFF

• Blinks if there is a problem with the Auto Idle Stop system.

• Comes on when Auto Idle Stop is in operation. The engine automatically shuts off.

Auto Idle Stop

Auto Idle Stop Suspend Indicator*

• Comes on while Auto Idle Stop is temporarily suspended in the following situations.

—

– The brake pedal is not fully pressed

• Depress the brake pedal firmly.

Auto Idle Stop 

– The transmission is in a position other than

(D

Auto Idle Stop

Auto Idle Stop

–  is ON (indicator on).

Auto Idle Stop Customizing the INDIVIDUAL Settings

• The battery temperature is too low.
• Auto Idle Stop does not activate for some reason.

Adaptive Cruise Control (ACC) with Low-Speed Follow* Indicator (Amber)

• Comes on if there is a problem with ACC with Low-Speed Follow*.

• Comes on while driving – Have your vehicle checked by a dealer.

• Comes on if the ACC with Low-Speed Follow* is deactivated temporarily after the battery has been disconnected, and then re-connected.

• Drive a short distance at more than 12 mph (20 km/h). The indicator should go off. If it does not, have your vehicle checked by a dealer.

• Indicators may come on temporarily when the Maximum Load Limit is exceeded.
• ACC with Low-Speed Follow* has been automatically canceled.

• Make sure the total load is within the Maximum Load Limit.

Maximum Load Limit

• Stays on constantly – Have your vehicle checked by a dealer.

• Lights up in white when you press the button.
• Lights up in green when you press the RES/+/ SET/− switch up or down.

Adaptive Cruise Control (ACC) with Low-Speed Follow Adaptive Cruise Control (ACC)

Lane Keeping Assist System (LKAS) Indicator (Amber)

• Comes on if there is a problem with the LKAS.

• Stays on constantly – Have your vehicle checked by a dealer.

• Indicators may come on temporarily when the Maximum Load Limit is exceeded.

• Make sure the total load is within the Maximum Load Limit.

Maximum Load Limit 

• Stays on constantly – Have your vehicle checked by a dealer.

• Lights up in white when you press the LKAS button.
• Lights up in green when the LKAS is in operation.

Lane Keeping Assist System (LKAS)

• Lights up in white when you change to cruise mode.
• Lights up in green when you have set a speed for cruise control.

To Switch ACC with Low-Speed Follow to Cruise Control  To Switch ACC to Cruise Control 

• Comes on when Adaptive Cruise Control (ACC) with Low-Speed Follow* indicator comes on.

To Set or Change Following-interval

Safety Support Indicator (Amber)

• Comes on if there is a problem with the Road Departure Mitigation system, CMBSTM, Low-Speed Braking Control*, or blind spot information system.

• Stays on constantly – Have your vehicle checked by a dealer.

• Comes on if there is a problem with the parking sensor.

• Check if the area around the sensor(s) is covered with mud, ice, snow, etc. If the indicator stays on even after you clean the area, have the system checked by a dealer.

• Indicators may come on temporarily when the Maximum Load Limit is exceeded.

• Make sure the total load is within the Maximum Load Limit.

Maximum Load Limit

• Stays on constantly – Have your vehicle checked by a dealer.

• Comes on if the Road Departure Mitigation system, CMBSTM, and Low-Speed Braking Control* are deactivated temporarily after the battery has been disconnected and then re-connected.

• Drive a short distance at more than 12 mph (20 km/h). The indicator should go off. If it does not, have your vehicle checked by a dealer.

Safety Support Indicator (Amber)

• Comes on when the Road Departure Mitigation system and/or CMBSTM shuts itself off.

• Stays on – The temperature inside the camera is too high.

Use the climate control system to cool down the camera.

The system activates when the temperature inside the camera cools down.

Front Wide-View Camera

• Stays on – The area around the camera is blocked by dirt, mud, etc. Stop your vehicle in a safe place and wipe the debris off with a soft cloth.
• Have your vehicle checked by a dealer if the indicator and message are still displayed even after you have cleaned the area around the camera.

Front Wide-View Camera

• It may come on when the ambient conditions are dark, such as when driving in a tunnel, or at night, dawn, or dusk.

Safety Support Indicator (Amber)

• Comes on when mud, snow, or ice accumulates in the vicinity of the sonar sensor.

• Remove the obstacle in the vicinity of the sonar sensor.

Low-Speed Braking Control

• Comes on when mud, snow, or ice accumulates in the vicinity of the blind spot information system sensor.
• Comes on when the temperature of the blind spot information system sensor is high.

• Comes on while driving – Something may be interfering with the blind spot information system sensor. Check the vicinity of the blind spot information system sensor and remove any obstacles.
• The system will return to normal when the temperature cools down.

Blind Spot Information System

Safety Support Indicator (Green/ Gray)

• Lights up in green when the Road Departure Mitigation system, CMBSTM, Low-Speed Braking Control*, blind spot information system, and parking sensor system* are on.
• Lights up in green and gray when the Road Departure Mitigation system, CMBSTM, Low-Speed Braking Control*, blind spot information system, parking sensor system*, or any two, three, or four of these systems are off.
• Lights up in gray when the Road Departure Mitigation system, CMBSTM, Low-Speed Braking Control*, blind spot information system, and parking sensor system* are off.

Road Departure Mitigation System  Blind Spot Information System Low-Speed Braking Control Collision Mitigation Braking SystemTM (CMBSTM) Parking Sensor System