ACURA Integra 2023 Display Gauges and Indicators User Guide

Indicators

Indicators come on/blink depending on the condition of the vehicle. Messages may display on the driver information interface at the same time. Please take the appropriate action outlined in the message, such as contacting a dealer.

1. When you set the power mode to ON, these indicators come on to indicate that system checks are being performed. They go off a few seconds later or after the engine has started. If an indicator does not come on or turn off, there may be a malfunction in the corresponding system. To resolve the issue, follow the instructions in the owner’s manual.

1. When you set the power mode to ON, these indicators come on to indicate that system checks are being performed. They go off a few seconds later or after the engine has started. If an indicator does not come on or turn off, there may be a malfunction in the corresponding system. To resolve the issue, follow the instructions in the owner’s manual.

Indicator	Name	On/Blinking	Explanation
	Parking Brake and Brake System Indicator (Red)	●  Comes on when the parking brake is applied, and goes off when it is released.	The beeper sounds and the indicator comes on if you drive with the parking brake applied. Comes on for about 30 seconds when you apply the electric parking brake while the power mode is in ACCESSORY or VEHICLE OFF, then goes off. Stays on for about 30 seconds when you set the power mode to VEHICLE OFF while the electric parking brake is applied, then goes off.
		•  Comes on when the brake fluid level is low.	Comes on while driving – Make sure the parking brake is released. Stop in a safe place and check the brake fluid level. 2 What to do when the indicator comes on while driving P. 701

Indicator	Name	On/Blinking	Explanation
	Parking Brake and Brake System Indicator (Red)	●  Comes on if there is a problem with the brake system.	Continuously variable transmission models Comes on along with the Parking Brake and Brake System Indicator (amber) – Immediately stop in a safe place. Contact a dealer for repair. The brake pedal becomes harder to operate. Depress the pedal further than you normally do. 2 If the Brake System Indicator (Red) Comes On or Blinks at the Same Time When the Brake System Indicator (Amber) Comes On P. 703 All models Comes on along with the ABS indicator – Have your vehicle checked by a dealer. 2 If the Brake System Indicator (Red) Comes On or Blinks P. 701 Blinks and the Parking Brake and Brake System Indicator (amber) comes on at the same time – There is a problem with the electric parking brake system. The parking brake may not be set. Avoid using the parking brake and have your vehicle checked by a dealer immediately. 2 If the Brake System Indicator (Red) Comes On or Blinks at the Same Time When the Brake System Indicator (Amber) Comes On P. 703

Indicator	Name	On/Blinking	Explanation
	Parking Brake and Brake System Indicator (Amber)	Comes on if there is a problem with a system related to braking other than the conventional brake system.	Comes on while driving – Have your vehicle checked by a dealer. With this indicator on, your vehicle still has normal braking ability.
		Comes on if there is a problem with the electric parking brake system and/or the automatic brake hold system.	Stays on constantly – Avoid using the parking brake and have your vehicle checked by a dealer immediately.
	Automatic Brake Hold System Indicator	Comes on when the automatic brake hold system is on.	2 Automatic Brake Hold P. 589
	Automatic Brake Hold Indicator	Comes on when the automatic brake hold is activated.	2 Automatic Brake Hold P. 589

Indicator	Name	On/Blinking	Explanation
	Malfunction Indicator Lamp	After you have set the power mode to ON, the vehicle performs system checks. However, if the readiness codes have not been set by that time, this indicator will blink five times and then go off.	Readiness codes are part of the on-board diagnostics for the emissions control systems. 2 Testing of Readiness Codes P. 721
		Comes on if there is a problem with the emissions control systems. Blinks when a misfire in the engine’s cylinders is detected.	2 If the Malfunction Indicator Lamp Comes On or Blinks P. 700
	Charging System Indicator	Comes on when there is a problem with the charging system.	Stop in a safe place and contact a dealer immediately. 2 Checking the Battery P. 651 2 If the Charging System Indicator Comes On P. 700
	Shift Position Indicator*	Indicates the current shift position.	2 Shifting P. 440
	M (7-speed manual shift mode) Indicator/Shift Indicator*	Comes on when the 7-speed manual shift mode is applied.	2 7-Speed Manual Shift Mode P. 442

Indicator	Name	On/Blinking	Explanation
	Transmission System Indicator*	Blinks if the transmission system has a problem.	Have your vehicle checked by a dealer immediately.
	Seat Belt Reminder Indicator	Blinks and the beeper sounds for a few seconds if you are not wearing a seat belt when you set the power mode to ON, then the indicator comes on. If the front passenger is not wearing a seat belt, the indicator comes on a few seconds later. Comes on for a while when the rear seat belt is unfastened while the power mode in ON. Blinks while driving if you and/or any passenger has not fastened a seat belt. The beeper sounds and the indicator blinks at regular intervals.	The beeper stops and the indicator goes off when you and the passengers fasten their seat belts. Stays on after you and/or the passengers have fastened the seat belt(s) – A detection error may have occurred in the sensor. Have your vehicle checked by a dealer. 2 Seat Belt Reminder P. 42

Indicator	Name	On/Blinking	Explanation
	Low Fuel Indicator	Comes on when the fuel reserve is running low (approximately 1.8 U.S. gal/7.0 Liter left).	Comes on – Refuel your vehicle as soon as possible.
		Blinks if there is a problem with the fuel gauge.	Have your vehicle checked by a dealer.
	Anti-lock Brake System (ABS) Indicator	Comes on if there is a problem with the ABS.	Stays on constantly – Have your vehicle checked by a dealer. With this indicator on, your vehicle still has normal braking ability but no anti-lock function. 2 Anti-lock Brake System (ABS) P. 594
	Supplemental Restraint System Indicator	Comes on if a problem with any of the following is detected: Supplemental Restraint System Side airbag system Side curtain airbag system Seat belt tensioner	Stays on constantly – Have your vehicle checked by a dealer.
	Electric Power Steering (EPS) System Indicator	Comes on if there is a problem with the EPS system.	Stays on constantly – Have your vehicle checked by a dealer. Do not drive displays on the driver information interface – Immediately stop in a safe place and contact a dealer. 2 If the Electric Power Steering (EPS) System Indicator Comes On P. 702

Indicator	Name	On/Blinking	Explanation
	Vehicle Stability AssistTM (VSA®) System Indicator	Blinks when VSA® is active.	—
		Comes on if there is a problem with the VSA® system, brake assist system, hill start assist system, starting assist brake function*, or agile handling assist.	Stays on constantly – Have your vehicle checked by a dealer. 2 Vehicle Stability AssistTM (VSA®), aka Electronic Stability Control (ESC), System P. 466
		Comes on if the VSA® system is deactivated temporarily after the battery has been disconnected, then re-connected.	Drive a short distance at more than 12 mph (20 km/h). The indicator should go off. If it does not, have your vehicle checked by a dealer.
	Vehicle Stability AssistTM (VSA®) OFF Indicator	Comes on when you partially disable VSA®.	2 VSA® On and Off P. 467
	Low Tire Pressure/ TPMS Indicator	Comes on if the tire pressure of any of the tires becomes low.	Comes on while driving – Stop in a safe place, check tire pressures, and inflate the tire(s) if necessary.
		Blinks for about one minute, and then stays on if there is a problem with the TPMS with Tire Fill Assist, or when a compact spare tire* is temporarily installed.	Blinks and remains on – Have your vehicle checked by a dealer. If the vehicle is fitted with a compact spare tire*, get your regular tire repaired or replaced and put back on your vehicle as soon as you can.

 

Indicator	Name	On/Blinking	Explanation
	Turn Signal and Hazard Warning Indicators	Blinks when you operate the turn signal lever. Blinks along with all turn signals when you press the hazard warning button.	Does not blink or blinks rapidly – Have your vehicle checked by a dealer.
	Lights On Indicator	Comes on when the parking, tail, and other external lights are on.	2 Light Switches P. 176
	High Beam Indicator	Comes on when the high beam headlights are on.	—
	Auto High-Beam Indicator	Comes on when all the operating conditions of the auto high-beam are met.	2 Auto High-Beam P. 180
	Fog Light Indicator*	Comes on when the fog lights are on.	2 Fog Lights* P. 179

Indicator	Name	On/Blinking	Explanation
	System Message Indicator	Comes on along with a beep when a problem is detected. A system message on the driver information interface appears at the same time.	While the indicator is on, roll the right selector wheel to see the message again. 2 Switching the Display P. 112 Refer to the Indicators information in this chapter when a system message appears on the driver information interface. Respond to the message accordingly. The driver information interface will not return to the normal screen unless the warning is canceled, or the right selector wheel is rolled.
	NORMAL Mode Indicator	Comes on when you set the dynamic mode to NORMAL.	2 Acura Integrated Dynamics System P. 449
	COMFORT Mode Indicator	Comes on when you set the dynamic mode to COMFORT.	2 Acura Integrated Dynamics System P. 449
	SPORT Mode Indicator	Comes on when you set the dynamic mode to SPORT.	2 Acura Integrated Dynamics System P. 449
	INDIVIDUAL Mode Indicator*	Comes on when you set the INDIVIDUAL mode.	2 Acura Integrated Dynamics System P. 449

Indicator	Name	On/Blinking	Explanation
	Immobilizer System Indicator	Blinks if the immobilizer system cannot recognize the key information.	Blinks – You cannot start the engine. Set the power mode to VEHICLE OFF, then select the ON mode again.  Canadian models Depress and hold the brake pedal before setting the power mode to ON. Repeatedly blinks – The system may be malfunctioning. Have your vehicle checked by a dealer. Do not attempt to alter this system or add other devices to it. Electrical problems can occur.
	Security System Alarm Indicator	Blinks when the security system alarm has been set.	2 Security System Alarm P. 165

Indicator	Name	On/Blinking	Explanation
	Auto Idle Stop OFF Indicator	Comes on when the Auto Idle Stop system has been turned off by the Auto Idle Stop OFF button.	2 Auto Idle Stop System ON/OFF P. 456, 462
	Auto Idle Stop System Indicator (Amber)	Blinks if there is a problem with the Auto Idle Stop system.	Blinks – Have your vehicle checked by a dealer.
	Auto Idle Stop Indicator (Green)	Comes on when Auto Idle Stop is in operation. The engine automatically shuts off.	2 Auto Idle Stop P. 455, 461

Indicator	Name	On/Blinking	Explanation
	Auto Idle Stop Suspend Indicator	Comes on while Auto Idle Stop is temporarily suspended in the following situations.
		Continuously variable transmission models Brake pedal is not fully pressed	●  Depress the brake pedal firmly.
		Continuously variable transmission models The transmission is in a position other than (D	2 Auto Idle Stop P. 455
		System charging is prioritized	2 Auto Idle Stop P. 455, 461
		Climate control system is prioritized
		Engine coolant temperature is not in operating range
		The Integrated Dynamics System mode is in SPORT or INDIVIDUAL* mode (when the Auto Idle Stop setting is set to Disable).	2 Auto Idle Stop P. 455, 461 2 Customizing the INDIVIDUAL Settings P. 453
		The battery temperature is too low. Auto Idle Stop does not activate for some reason.	2 Auto Idle Stop P. 455, 461
			If you press and hold the Auto Idle Stop OFF button, you can select whether to display the status messages or not.

Indicator	Name	On/Blinking	Explanation
	Adaptive Cruise Control (ACC) with Low Speed Follow* Indicator (Amber)	Comes on if there is a problem with ACC with Low Speed Follow*.	Comes on while driving – Have your vehicle checked by a dealer.
		Comes on if the ACC with Low Speed Follow* is deactivated temporarily after the battery has been disconnected, then reconnected.	Drive a short distance at more than 12 mph (20 km/h). The indicator should go off. If it does not, have your vehicle checked by a dealer.
		Indicator may come on temporarily when the Maximum Load Limit is exceeded. ACC with Low Speed Follow* has been automatically canceled.	Make sure the total load is within the Maximum Load Limit. 2 Maximum Load Limit P. 427 Stays on constantly – Have your vehicle checked by a dealer.
	Adaptive Cruise Control (ACC) with Low Speed Follow* Indicator (White/Green)	Lights up in white when you press the button. Lights up in green when you press the up or down the RES/+/SET/− switch.	2 Adaptive Cruise Control (ACC) with Low Speed Follow* P. 504 2 Adaptive Cruise Control (ACC)* P. 525

Indicator	Name	On/Blinking	Explanation
	Lane Keeping Assist System (LKAS) Indicator (Amber)	Comes on if there is a problem with the LKAS.	Stays on constantly – Have your vehicle checked by a dealer.
		Indicator may come on temporarily when the Maximum Load Limit is exceeded.	Make sure the total load is within the Maximum Load Limit. 2 Maximum Load Limit P. 427 Stays on constantly – Have your vehicle checked by a dealer.
	Lane Keeping Assist System (LKAS) Indicator (White/Green)	Lights up in white when you press the LKAS button. Lights up in green when the LKAS is in operation.	2 Lane Keeping Assist System (LKAS) P. 545
	Cruise Mode Indicator (White/Green)	Lights up in white when you change to cruise mode. Lights up in green when you have set a speed for cruise control.	2 To Switch ACC with Low Speed Follow to Cruise Control P. 522 2 To Switch ACC to Cruise Control P. 542
	Adaptive Cruise Control (ACC) with Low Speed Follow* Interval Indicator	Comes on when Adaptive Cruise Control (ACC) with Low Speed Follow* indicator comes on.	Each time you press the interval button, the following interval (the interval behind a vehicle detected ahead of you) setting cycles through extra long, long, middle, and short following intervals. 2 To Set or Change Following-interval P. 517, 537

Indicator	Name	On/Blinking	Explanation
	Safety Support Indicator (Amber)	Comes on if there is a problem with Road Departure Mitigation system, CMBSTM, Low Speed Braking Control*, or blind spot information system.	Stays on constantly – Have your vehicle checked by a dealer.
		Models with parking sensor system Comes on if there is a problem with the parking sensor.	Check if the area around the sensor(s) is covered with mud, ice, snow, etc. if the indicator stays on even after you clean the area, have the system checked by a dealer.
		Indicator may come on temporarily when the Maximum Load Limit is exceeded.	Make sure the total load is within the Maximum Load Limit. 2 Maximum Load Limit P. 427 ●  Stays on constantly – Have your vehicle checked by a dealer.
		Comes on if the Road Departure Mitigation system, CMBSTM and Low Speed Braking Control* are deactivated temporarily after the battery has been disconnected and then re-connected.	Drive a short distance at more than 12 mph (20 km/h). The indicator should go off. If it does not, have your vehicle checked by a dealer.

Indicator	Name	On/Blinking	Explanation
	Safety Support Indicator (Amber)	Comes on when the Road Departure Mitigation system and/or CMBSTM shuts itself off.	Stays on – The temperature inside the camera is too high. Use the climate control system to cool down the camera. The system activates when the temperature inside the camera cools down. 2 Front Wide View Camera P. 581
			Stays on – The area around the camera is blocked by dirt, mud, etc. Stop your vehicle in a safe place and wipe the debris off with a soft cloth. Have your vehicle checked by a dealer if the indicator and message are still displayed even after you have cleaned the area around the camera. 2 Front Wide View Camera P. 581 It may come on when the ambient conditions are dark, such as when driving in a tunnel, or at night, dawn, or dusk.

Indicator	Name	On/Blinking	Explanation
	Safety Support Indicator (Amber)	Models with Low Speed Braking Control Comes on when mud, snow, or ice accumulates in the vicinity of the sonar sensor.	Remove the obstacle in the vicinity of the sonar sensor. 2 Low Speed Braking Control* P. 493, 499
		Comes on when mud, snow, or ice accumulates in the vicinity of the blind spot information system sensor. Comes on when the temperature of the blind spot information system sensor is high.	Comes on while driving – Something may be interfering with the blind spot information system sensor. Check the vicinity of the blind spot information system sensor and remove any obstacles. The system will return to normal when the temperature cools down. 2 Blind Spot Information System P. 474

Indicator	Name	On/Blinking	Explanation
	Safety Support Indicator (Green/ Gray)	Lights up in green when Road Departure Mitigation system, CMBSTM, Low Speed Braking Control*, blind spot information system and parking sensor system* are on. Lights up in green and gray when Road Departure Mitigation system, CMBSTM, Low Speed Braking Control*, blind spot information system, parking sensor system* or any two, three or four of these systems are off. Lights up in gray when Road Departure Mitigation system, CMBSTM, Low Speed Braking Control*, blind spot information system and parking sensor system* are off.	2 Road Departure Mitigation System P. 566 2 Blind Spot Information System P. 474 2 Low Speed Braking Control* P. 493, 499 2 Collision Mitigation Braking System (CMBS) P. 481 2 Parking Sensor System* P. 598

Gauges and Displays

Gauges
Gauges include the speedometer, fuel gauge, and other related indicators. They are displayed when the power mode is in ON.

Speedometer
Displays your driving speed in mph or km/h.

If you change the unit from miles and mph to km and km/h, the current vehicle speed in mph appears next to the digital speedometer.

Tachometer
Shows the number of engine revolutions per minute.

Fuel Gauge
Displays the amount of fuel left in the fuel tank.

Temperature Gauge
Displays the temperature of the engine coolant.

Odometer
Shows the total number of miles or kilometers that your vehicle has accumulated.

NOTICE
You should refuel when the reading approaches E Running out of fuel can cause the engine to misfire, damaging the catalytic converter.
The actual amount of remaining fuel may differ from the fuel gauge reading.

NOTICE
Driving with the temperature gauge reading in the upper zone can cause serious engine damage. Pull safely to the side of the road and allow engine temperature to return to normal.

Outside Temperature
Shows the outside temperature in Fahrenheit (U.S.) or Celsius (Canada).

Adjusting the outside temperature display
Adjust the temperature reading by up to ±5°F or ±3°C if the temperature reading seems incorrect.

• Traffic Sign Recognition System
  Shows certain detected traffic signs while driving.
• The indicator blinks when the maximum speed of the traffic sign detected by the Traffic Sign Recognition System is exceeded.
  Traffic Sign Recognition System P. 574

The temperature sensor is in the front bumper. Road heat and exhaust from another vehicle can affect the temperature reading when your vehicle speed is less than 19 mph (30 km/h).
It may take several minutes for the display to be updated after the temperature reading has stabilized.
You can adjust the temperature reading.

Current Mode for ACC with Low Speed Follow*, the LKAS, and Traffic Jam Assist*
Shows the current mode for ACC with Low Speed Follow*, LKAS, and Traffic Jam Assist*.

1. Adaptive Cruise Control (ACC) with Low Speed Follow* P. 504
2. Adaptive Cruise Control (ACC)* P. 525
3. Traffic Jam Assist* P. 557

When you set speed for ACC with Low Speed Follow* or cruise control, a set speed mark will be displayed on the speedometer.

Driver Information Interface (Left Side Area)
Shows the current mode for audio and phone information, etc.
Audio Remote Controls P. 230
Bluetooth® HandsFreeLink® P. 383, 403

Clock
Shows the clock.

You can adjust the time manually and change the clock display to show the 12 hour clock or 24 hour clock.
Clock P. 142
You can choose whether the clock is displayed on the driver information interface.
Customize Display P. 109

Customize Display
Arrange audio source on the left side area
You can choose which sources to display on the audio source screen.

1. Roll the left selector wheel until Customize display is selected, then press the left selector wheel.
   

Roll the left selector wheel to scroll to select Hide/show, then press the left selector wheel.
Turn the displaying on the left side area on and off
You can select whether the current audio information and clock appear on the left side area.

1. Roll the left selector wheel until Customize display is selected, then press the left selector wheel.
   
2. Roll the left selector wheel to scroll to select Audio & clock, then press the left selector wheel.
   
3. Roll the left selector wheel to scroll to select your desired settings, then press the left selector wheel.

Driver Information Interface (Right Side Area)
The driver information interface shows information such as the estimated travelable distance and fuel economy of the vehicle. It also displays messages such as warnings and other helpful information.
When a warning message displays, please check the message and contact a dealer and have the vehicle inspected if necessary. Please refer to the pages below if the Engine oil pressure low or Engine temperature too hot message is displayed.
If the Engine oil pressure low Warning Appears P. 699
Overheating P. 697

Switching the Display
Roll the right selector wheel to view different types of content.

Range/Fuel/Trip Meter
Press the right selector wheel to switch between trip meter A and trip meter B.

• Trip meter
  Shows the total number of miles or kilometers driven since the last reset. Meters A and B can be used to measure two separate trips.

Resetting a trip meter
To reset the trip meter, display it, press and hold the right selector wheel and then select Reset.

•  Average fuel economy
  Shows the estimated average fuel economy of each trip meter in mpg or l/100 km. The display is updated at set intervals. When a trip meter is reset, the average fuel economy is also reset.
• Instant fuel economy
  Shows the instant fuel economy as a bar graph in mpg or l/100 km.
• Range
  Shows the estimated distance you can travel on the remaining fuel. This estimated distance is based on the vehicle’s current fuel economy.

Speed/Time/Trip Meter
Press the right selector wheel to switch between trip meter A and trip meter B.

• Trip meter
  Trip meter P. 113
• Elapsed time
  Shows the time elapsed since Trip A or Trip B was reset.
• Average speed
  Shows the average speed in mph or km/h since Trip A or Trip B was reset.

Navigation*
Compass
Shows the compass screen.

Turn-by-Turn Directions
When driving guidance is provided by the Apple CarPlay or Android Auto, turn-by-turn directions to your destination appear.

Apple CarPlay P. 315
Android AutoTM P. 322

You can select whether to have the turn-by-turn display come on or not during the route guidance.
Customized Features P. 359
Turn-by-turn directions may not be available for all apps.

Driver Attention Monitor
The Driver Attention Monitor analyzes steering inputs to determine if the vehicle is being driven in a manner consistent with drowsy or inattentive driving. If it determines that the vehicle is being driven in such a manner, it will display the degree of the driver’s attention on the driver information interface.

When you select Driver Attention Monitor on the driver information interface, bars on it light up in white to indicate the degree of the driver’s attention.
Switching the Display P. 112

If two bars light up, the Driver attention level low message will appear.
If one bar lights up, the Driver attention level low. Time for a break. message will appear, a beep will sound, and the steering wheel will vibrate.
If this message appears, stop in a safe location and rest for as long as needed.
The message will disappear when the right selector wheel is rolled or when the system has determined that the driver is driving normally.
If the driver does not take a break and the monitor continues to detect that the driver is very tired, the message will appear again after approximately 15 minutes, accompanied by a beep and steering wheel vibrations.
The message does not appear when the traveling time is 30 minutes or less.

The Driver Attention Monitor resets when:

The engine is turned off.
The driver unfastens the seat belt and opens the door while the vehicle is stopped.

For the Driver Attention Monitor to function:

• The vehicle must be traveling above 25 mph (40 km/h).
  The electric power steering (EPS) system indicator must be off.

Depending on driving conditions or other factors, the Driver Attention Monitor may not function in the following circumstances:

The steering assist function of the Lane Keeping Assist System (LKAS) is active. 2 Lane Keeping Assist System (LKAS) P. 545
The condition of the road is poor, e.g. the surface is unpaved or bumpy.
It is windy.
The driver is frequently operating the vehicle in an assertive manner such as changing lanes or accelerating.

Customizing
You can change the Driver Attention Monitor settings. Select Tactile and audible alert*1/Tactile And Audible Alert*2, Tactile alert*1/Tactile Alert*2, or OFF.

Models with 7-in. Color Touchscreen
Vehicle Settings* P. 126

Models with 9-in. Color Touchscreen
Customized Features P. 359

1. Models with 7-in. Color Touchscreen
2. Models with 9-in. Color Touchscreen
   1. Not available on all models

Seat Belt
pears, under specified conditions, when seat belts are latched or unlatched.
Seat Belt Reminder P. 42

Maintenance
Shows the remaining oil life and Maintenance MinderTM.
Maintenance MinderTM P. 617

Tire Pressure Monitor
Shows each tire’s pressure.
Tire Pressure Monitoring System (TPMS) with Tire Fill Assist P. 470

Tire pressure status is displayed via green and amber icons.
The icons turn amber if tire pressure is too low, or if there is a problem with the system. “–” is displayed if there is a problem.

Safety Support
Indicates the status of the Road Departure Mitigation system, CMBSTM, Low Speed Braking Control*, blind spot information system and parking sensor system* such as On, Off, or Failure, by color and letters.

The following colors indicate the status of any of the above mentioned systems:

• Green: The system is on.
  Gray: The system is off.
  Amber: There is a problem with the system.

If a system is indicated by the color amber, have your vehicle checked by a dealer immediately.
To turn on or off each system, first press the right selector wheel to switch displays. From the next display you can select which system to turn on or off.

Even when the Low Speed Braking Control icon is green, if the Rear Sensor Setting is turned off, the brake assist will not operate when reversing.
Customized Features P. 359
Even when the Parking Sensor System icon is green, if the Rear Sensor Setting is turned off, the rear parking sensor will not operate when reversing.

Speed/Distance Units
Enables you to show another unit on the driver information interface, head-up display* and set the displayed measurements to read in either miles and mph or km and km/h.
Press and hold the right selector wheel when you select the No Content/Unit Change screen on the driver information interface. Each time you do this, the unit will change from miles and mph to km and km/h or vice versa. After this, a confirmation screen will appear for a few seconds.

Brightness
Display the adjustment for instrument panel brightness.
When the power mode is in ON, you can use the right selector wheel to adjust instrument panel brightness.
Brighten: Roll the right selector wheel up.
Dim: Roll the right selector wheel down.
Press the right selector wheel to exit.

The brightness of the gauge is automatically adjusted depending on the ambient brightness.

The brightness dims when the ambient light is dark.
The brightness brightens when the ambient light is bright.

You can change the setting even when the ambient lighting is bright, but the brightness of the gauge won’t change.

Gauge Display Settings
Arrange content on the right side area
You can choose which contents to display on the right side area.

1. Press the right selector wheel when you select the Gauge display settings on the driver information interface.
2. Roll the right selector wheel to scroll to select Hide/show, then press the right selector wheel.
   
3. Roll the right selector wheel to scroll between contents, then press the right selector wheel to check or uncheck them.

Warnings
You can check if there are any active warning messages.

Contents that are gray cannot be removed from the right side area.

Continuously variable transmission models
When you customize settings, shift to (P.

Manual transmission models
When you customize settings, set the parking brake.

If there are multiple warnings, you can roll the right selector wheel to see other warnings.

Vehicle Settings*
Use the driver information interface to customize certain features.

How to customize
Roll the right selector wheel to scroll to select screen while the power mode is in ON, the vehicle is at a complete stop, and the shift position is in (P. Then, press the right selector wheel.

To customize other features, roll the right selector wheel.

List of customizable options P. 127
Example of customization settings P. 133

When you customize settings, shift to (P.

List of customizable options

	Forward collision	Changes the distance at which CMBSTM alerts.	Long/Normal*1/Short
	warning distance
Driver assist system setup	ACC forward vehicle detect beep	Causes the system to beep when a vehicle is detected or when the vehicle is out of ACC with Low Speed Follow range.	ON/OFF*1
	Road departure mitigation setting	Changes the setting for the Road Departure Mitigation system.	Narrow/Normal*1/Wide/ Warning only
	Lane keeping assist	Causes the system to beep when the LKAS is suspended.	ON/OFF*1
	suspend beep
	Blind spot information	Changes the setting for the blind spot information.	Audible and visual alert*1/Visual alert

 

	Traffic sign
	recognition system	Turns the traffic sign recognition system on and off.	ON*1/OFF
	display setting
	Traffic sign
	recognition system	Turns the traffic sign recognition system over speed	ON*1/OFF
	exceeding speed	warning on and off.
	warning
Driver assist			Speed limit*1/ Speed limit+3mph/ Speed limit+5mph/ Speed limit+10mph (When mph is selected)   Speed limit*1/ Speed limit+5km/h/ Speed limit+10km/h/ Speed limit+15km/h (When km/h is selected)
system setup
	Speed limit warning threshold setting	Changes the setting speed the traffic sign recognition system over speed warning is activated.
	Driver attention	Changes the setting for the driver attention monitor.	Tactile and audible
	monitor		alert*1/ Tactile alert/OFF

Door setup	Auto door lock	Changes the setting for when the doors and the hatch automatically lock.	With vehicle speed*1/Shift from P/OFF
	Auto door unlock	Changes the setting for when the doors and the hatch automatically unlock.	All doors when driver’s door opens*1/All doors when shifted to Park/All doors when ignition switched OFF/OFF
	Walk away auto lock	Changes the settings for the automatic locking the doors when you walk away from the vehicle while carrying the keyless remote.	ON/OFF*1
	Keyless lock answer back	LOCK/UNLOCK- The exterior lights flash. LOCK (2nd push)- The beeper sounds.	ON*1/OFF
	Keyless remote power window control	Turns remote window control using the keyless remote on and off.	ON*1/OFF
	Lockout prevention	Changes the settings for the lockout protection function.	ON*1/OFF
	Lock presetting	Changes the settings for the lock presetting function.	ON*1/OFF

Example of customization settings
The steps for changing the “Trip A” reset timing setting to When fully refueled are shown below. The default setting for “Trip A” reset timing is Manually reset.

1. Roll the right selector wheel to select Vehicle settings, then press the right selector wheel.
   
2. Roll the right selector wheel until Meter setup appears on the display.
3. Press the right selector wheel.
   
4. Roll the right selector wheel until “Trip A” reset timing appears on the display, then press the right selector wheel.
   •  The display switches to the customization setup screen, where you can select When fully refueled, IGN OFF, Manually reset, or Back.
     
5.  Roll the right selector wheel and select When fully refueled, then press the right selector wheel.
   • The Selected appears, then the display returns to the customization menu screen.
     
6. Press the right selector wheel after Back appears on the display.
7. Repeat Step 6 until you return to the normal screen.

Head-Up Display
Shows the current mode for ACC with Low Speed Follow*, LKAS, and Traffic Jam Assist*, traffic sign recognition system, or turn-by-turn directions along with the vehicle speed. You can choose which item to be displayed using the driver information interface. They are displayed when the power mode is in ON.

The display also shows the following Warning

• Lane Departure Warning: When your vehicle is too close to the traffic lane lines, the lane departure warning appears.
  Lane Keeping Assist System (LKAS) P. 545
• Head-up Warning Lights:
  Flash when the BRAKE message appears on the driver information interface.
• Collision Mitigation Braking SystemTM
  (CMBSTM) P. 481
  Low Speed Braking Control
  P. 493, 499
  Adaptive Cruise Control (ACC) with
  Low Speed Follow* P. 504
  Adaptive Cruise Control (ACC)* P. 525

Head-Up Display Settings
Shows the display for changing the head-up display settings on the driver information interface.
Roll the right selector wheel to scroll to select Head-Up Display settings, then press the right selector wheel.
Switching the Display P. 112

To change head-up display content

Roll the right selector wheel to scroll to select HUD content, then press the right selector wheel.
Roll the right selector wheel to scroll to select desired item, then press the right selector wheel.

• Speedometer
  Speedometer P. 139
• Navigation
  Navigation P. 139
• Driver assist
  Current Mode for ACC with Low Speed Follow*, LKAS, and Traffic Jam
  Assist* P. 139
• OFF

Adjusting the head-up display brightness
Roll the right selector wheel to scroll to select HUD brightness, then press the right selector wheel.

Brighten: Roll the right selector wheel up. Dim: Roll the right selector wheel down.
Press the right selector wheel to exit.

Adjusting the head-up display height
Roll the right selector wheel to scroll to select HUD height, then press the right selector wheel.

Raise the head-up display: Roll the right selector wheel up. Lower the head-up display: Roll the right selector wheel down.
Press the right selector wheel to exit.

When you unlock and open the driver’s door with a remote transmitter or keyless access system, the head-up display adjusts automatically to one of the two preset positions.

Speedometer
Shows your driving speed in mph or km/h.

Current Mode for ACC with Low Speed Follow*, LKAS, and Traffic Jam Assist*
Shows the current mode for ACC with Low Speed Follow*, LKAS, and Traffic Jam Assist*.

Adaptive Cruise Control (ACC) with Low Speed Follow* P. 504
Adaptive Cruise Control (ACC)* P. 525
Lane Keeping Assist System (LKAS) P. 545
Traffic Jam Assist* P. 557

Navigation
Compass
Shows the compass screen.

Turn-by-Turn Directions
When driving guidance is provided by the Android Auto or Apple CarPlay, turn-by-turn directions to your destination appear.

Android AutoTM P. 322
Apple CarPlay P. 315

Traffic Sign Recognition System
Shows the traffic sign recognition system.
The indicator blinks when the maximum speed of the traffic sign detected by the Traffic Sign Recognition System is exceeded.
Traffic Sign Recognition System P. 574
Not available on all models

You can select whether the turn-by-turn display comes on during the route guidance.
Customized Features P. 359
Turn-by-turn directions may not be available for all apps.

Reference Links

View Full User Guide: Acura Integra 2023 User Guide
Download Manuals: Acura | Owner’s Manual & Warranty | Acura Owner’s Site

2024 Acura INTEGRA Specs, Price, Features, Mileage (Brochure)

Related Article:

2023 Acura TLX Specs, Price, Features, Mileage (Brochure)

2023 Acura RDX Specs, Price, Features, Mileage (Brochure)

2023 Acura MDX Specs, Price, Features, Mileage (Brochure)