• Comes on when the parking brake is applied, and goes off when it is released.

• The beeper sounds and the indicator comes on if you drive with the parking brake applied.
• Comes on for about 30 seconds when you apply the electric parking brake while the power mode is in ACCESSORY or VEHICLE OFF, then goes off.
• Stays on for about 30 seconds when you set the power mode to VEHICLE OFF while the electric parking brake is applied, then goes off.

Canada

• Comes on if there is a problem with the brake system.

• Comes on along with the Parking Brake and Brake System Indicator (amber) – Immediately stop in a safe place. Contact a dealer for repair. The brake pedal becomes harder to operate. Depress the pedal further than you normally do.
  If the Brake System Indicator (Red) Comes On or Blinks at the Same Time When the Brake System Indicator (Amber) Comes On P. 675
• Comes on along with the ABS indicator – Have your vehicle checked by a dealer.

If the Brake System Indicator (Red) Comes On or Blinks P. 673

•  Comes on if there is a problem with the brake system.

• Blinks and the Parking Brake and Brake System Indicator (amber) comes on at the same time – There is a problem with the electric parking brake system. The parking brake may not be set. Avoid using the parking brake and have your vehicle checked by a dealer immediately.

If the Brake System Indicator (Red) Comes On or Blinks at the Same Time When the Brake System Indicator (Amber) Comes On P. 675

U.S.

Canada

•  Comes on when the brake fluid level is low.

• Comes on while driving – Make sure the parking brake is released. Stop in a safe place and check the brake fluid level. What to do when the indicator comes on while driving P. 673

• Comes on if there is a problem with a system related to braking other than the conventional brake system.

• Comes on while driving – Avoid high speeds and sudden braking. Take the vehicle to a dealer immediately.

•  Comes on if there is a problem with the electric parking brake system and/or the automatic brake hold system.

• Stays on constantly – Avoid using the parking brake and have your vehicle checked by a dealer immediately.

• Comes on if there is a problem with the radar sensor.
• Indicator may come on temporarily when the Maximum Load Limit is exceeded.

•  Make sure the total load is within the Maximum Load Limit.
  Maximum Load Limit P. 433
• Stays on constantly – Have your vehicle checked by a dealer.

• Comes on when the automatic brake hold system is on.

• Comes on when the automatic brake hold is activated.

•  After you have set the power mode to ON, the vehicle performs system checks. However, if the readiness codes have not been set by that time, this indicator will blink five times and then go off.

• Readiness codes are part of the on-board diagnostics for the emissions control systems.
  Testing of Readiness Codes P. 695

• Comes on if there is a problem with the emissions control systems.
• Blinks when a misfire in the engine’s cylinders is detected.

• Comes on when there is a problem with the charging system.

•  Stop in a safe place and contact a dealer immediately.
  Checking the Battery P. 623
  If the Charging System Indicator Comes On P. 672

• The current gear selection blinks if the transmission system has a problem.

• Blinks while driving – Avoid sudden starts and acceleration and have your vehicle checked by a dealer immediately.

• The indicated current gear selection blinks if you cannot put the transmission into (R due to a transmission system failure.

• Avoid sudden starts, sudden acceleration and high speed, and have your vehicle checked by a dealer immediately.

•  The indicated current gear selection blinks if the transmission system has a problem and the performance of the vehicle is reduced.

• Avoid sudden starts, sudden acceleration and high speed, and have your vehicle checked by a dealer immediately.

• The indicated current gear selection blinks if the transmission system has a problem and the paddle shifters cannot be used.

• Have your vehicle checked by a dealer immediately.

• The current gear position or all the gear positions blink if there is a problem with the transmission and the vehicle is no longer able to run.

• Immediately park your car in a safe place.
• Emergency Towing P. 685
• Have your vehicle checked by a dealer.

• The current gear position or all the gear positions blink if there is a problem with the transmission and it is not possible to select (P.

• Depending on the circumstances, you can set the power mode to ON as an emergency measure.
  ]If the Transmission System Indicator Blinks along with the Warning Message P. 677
• While the vehicle is stopped, apply the parking brake.
• Have your vehicle checked by a dealer immediately.

• Comes on when Auto Idle Stop is in operation. The engine automatically shuts off.

•  Comes on when the Auto Idle Stop system has been turned off by the Auto Idle Stop system OFF button.

• Blinks if there is a problem with the Auto Idle Stop system.

• Blinks – Have your vehicle checked by a dealer.

• Comes on while Auto Idle Stop is temporarily suspended in the following situations.

• Depress the brake pedal firmly.

• The battery temperature is too low.
•  Auto Idle Stop does not activate for some reason.

• If you press and hold the Auto Idle Stop OFF button, you can select whether to display the status messages or not.

• Blinks and the beeper sounds for a few seconds if you are not wearing a seat belt when you set the power mode to ON, then the indicator comes on.
•  If the front passenger is not wearing a seat belt, the indicator comes on a few seconds later.
• Comes on for a while when the rear seat belt is unfastened while the power mode in ON.
• Blinks while driving if you and/or any passenger has not fastened a seat belt. The beeper sounds and the indicator blinks at regular intervals.

• The beeper stops and the indicator goes off when you and the passengers fasten their seat belts.
• Stays on after you and/or the passengers have fastened the seat belt(s) – A detection error may have occurred in the sensor. Have your vehicle checked by a dealer.
  Seat Belt Reminder P. 39

•  Comes on if a problem with any of the following is detected:
  • Supplemental Restraint System
  • Side airbag system
  •  Side curtain airbag system
  •  Seat belt tensioner

• Comes on if there is a problem with the EPS system.

• Stays on constantly – Have your vehicle checked by a dealer.
• Do Not Drive displays on the multi- information display – Immediately stop in a safe place and contact a dealer.
  If the Electric Power Steering (EPS) System Indicator Comes On P. 674

• Blinks when VSA® is active.
• Comes on if there is a problem with the VSA® system, brake assist system, hill start assist system, starting assist brake function or agile handling assist.

• Blinks when you operate the turn signal lever.
• Blinks along with all turn signals when you press the hazard warning button.

• Comes on when the parking, tail, and other external lights are on.

•  Comes on when the high beam headlights are on.

•   Comes on when all the operating conditions of the auto high-beam are met.

• Comes on when the fog lights are on.

• Blinks if the immobilizer system cannot recognize the key information.

• Blinks – You cannot start the engine. Set the power mode to VEHICLE OFF, then select the ON mode again.
  Canadian models
• Depress and hold the brake pedal before setting
  the power mode to ON.
• Repeatedly blinks – The system may be malfunctioning. Have your vehicle checked by a dealer.
• Do not attempt to alter this system or add other devices to it. Electrical problems can occur.

• Blinks when the security system alarm has been set.

• Comes on along with a beep when a problem is detected. A system message on the multi-information display appears at the same time.

• While the indicator is on, roll the right selector wheel to see the message again.
  SwitchingtheDisplayP. 139
• Refer to the Indicators information in this chapter when a system message appears on the multi-information display. Take the appropriate action for the message.
• The multi-information display does not return to the normal screen unless the warning is canceled, or the right selector wheel is pressed.

• Comes on if there is a problem with the SH-AWD® system.

• Stays on constantly – The engine drives the front wheels only in this state. Have your vehicle checked by a dealer.

• Blinks when the differential temperature is too high.

• Blinks while driving – Stop in a safe place, put the transmission into (P, and idle the engine until the indicator goes off. If the indicator does not stop blinking, take your vehicle to a dealer.
  Super Handling-All Wheel DriveTM (SH-AWD®)* P. 474

• Comes on when the scheduled maintenance is due soon.
• Consequently, Maintenance Due Now and Maintenance Past Due follow.

• Lights up in white when you change to cruise mode.
• Lights up in green when you have set a speed for cruise control.

• Comes on if there is a problem with ACC with Low Speed Follow.

• Comes on while driving – Have your vehicle checked by a dealer.

• Indicator may come on temporarily when the Maximum Load Limit is exceeded.
• ACC with Low Speed Follow has been automatically canceled.

• Make sure the total load is within the Maximum Load Limit.
  Maximum Load Limit P. 433
• Stays on constantly – Have your vehicle checked by a dealer.

• Lights up in white when you press the           button.
• Lights up in green when you press the RES/+ button or SET/– button.

• Comes on if there is a problem with the LKAS

• Stays on constantly – Have your vehicle checked by a dealer.

• Lights up in white when you press the LKAS button.
• Lights up in green when the LKAS is in operation.

•  Comes on if there is a problem with the Road Departure Mitigation system, CMBSTM, Low Speed Braking Control*, or blind spot information system.

• Stays on constantly – Have your vehicle checked by a dealer.

• Indicator may come on temporarily when the Maximum Load Limit is exceeded.

•  Make sure the total load is within the Maximum Load Limit.
  Maximum Load Limit P. 433
• Stays on constantly – Have your vehicle checked by a dealer.

• Comes on when the Road Departure Mitigation system, Low Speed Braking Control* and/or CMBSTM shuts itself off.

• Indicator may come on temporarily when passing through an enclosed space, such as a tunnel.
• The area around the radar sensor is blocked by dirt, mud, etc. Stop your vehicle in a safe place and wipe the debris off with a soft cloth. Indicator may take some time to go off after the radar sensor is cleaned.
• Have your vehicle checked by a dealer if the indicator does not go off even after you have cleaned the radar sensor.
  Radar Sensor P. 543

• Stays on – The temperature inside the camera is too high.
  Use the climate control system to cool down the camera.
  The system activates when the temperature inside the camera cools down.
  Front Sensor Camera P. 541

• Comes on when the Road Departure Mitigation system, Low Speed Braking Control* and/or CMBSTM shuts itself off.

• Stays on – The area around the camera is blocked by dirt, mud, etc.
• Stop your vehicle in a safe place and wipe the debris off with a soft cloth.
• Have your vehicle checked by a dealer if the indicator and message are still displayed even after you have cleaned the area around the camera.
  Front Sensor Camera P. 541

• Comes on when mud, snow, or ice has accumulated in the vicinity of the blind spot information system sensor.
• Comes on when the temperature of the blind spot information system sensor is high.

• Comes on while driving – Something may be interfering with the blind spot information system sensor. Check the vicinity of the blind spot information system sensor and remove any obstacles.
• The system will return to normal when the temperature cools down.
  Blind Spot Information System P. 479

• Comes on when mud, snow, or ice accumulates in the vicinity of the sonar sensor.

• Remove the obstacle in the vicinity of the sonar sensor.
  Low Speed Braking Control* P. 497

• Lights up in green when the Road Departure Mitigation system, CMBSTM, Low Speed Braking Control*, and blind spot information system are on.
• Lights up in green and gray when the Road Departure Mitigation system, CMBSTM, Low Speed Braking Control*, or blind spot information system, or any two or three of these systems are off.
• Lights up in gray when the Road Departure Mitigation system, CMBSTM, Low Speed Braking Control*, and blind spot information system are off.

• Appears when the vehicle is no longer able to run due to a malfunction.

• Immediately stop in a safe place.

• Appears when there is a risk that the vehicle will move unexpectedly after you have stopped due to a malfunction with the vehicle.

• While the vehicle is stopped, apply the parking brake.
  Parking Brake P. 545
• Have your vehicle checked by a dealer.

• Appears when you set the power mode to ON again and the vehicle is able to run.

•  Appears when the engine stops without the transmission in (P, and does not restart automatically.
• Appears if you open the hood while Auto Idle Stop activates.

• If you want to set the power mode to ON, put the transmission into (P.
• If you want to start the engine, follow the normal procedure.
  Starting the Engine P. 443

• Appears when the washer fluid is low.

• Refill the washer fluid.
  Refilling Window Washer Fluid P. 604

• Appears if there is a problem with the cooling system.

• Drive slowly to prevent overheating and have your vehicle checked by a dealer as soon as possible.

• Appears when the starter system has a problem.

•  As a temporary measure, press and hold the ENGINE START/STOP button for up to 15 seconds while pressing the brake pedal, manually start the engine. Have your vehicle checked by a dealer.

• Appears when the engine oil pressure is low.

• Appears while driving – Immediately stop in a safe place.
  If the Engine Oil Pressure Low Warning Appears
  P. 671

• Appears when the engine coolant temperature gets abnormally high.

• Appears when there is a problem with the power tailgate system.

• Manually open or close the power tailgate.
• Have the vehicle checked by a dealer.

• Appears if any door or the tailgate is not completely closed.
• Appears if any door or the tailgate is opened while driving. The beeper sounds.

• Disappears when all doors and the tailgate are closed.

•  Appears if there is a problem with the automatic lighting control system.

• Appears while driving – Manually turn the lights on, and have your vehicle checked by a dealer.

• Appears if there is a problem with the headlights.

• Appears while driving – The headlights may not be on. When conditions allow you to drive safely, have your vehicle checked by a dealer as soon as possible.

• Appears when there is a problem with the battery charging system.

• Have your vehicle checked by a dealer.

•  Appears if the dynamic mode cannot be changed due to certain situations, such as a system error or adverse driving conditions.

•  Appears when the automatic brake hold system is turned off.

•  Appears when the automatic brake hold button is pressed without wearing the driver’s seat belt.

•  Fasten the driver’s seat belt.
  Automatic Brake Hold P. 550

• Appears when the automatic brake hold button is pressed without depressing the brake pedal while the automatic brake hold is in operation.

• Press the automatic brake hold button with the brake pedal depressed.
  Automatic Brake Hold P. 550

• Appears when the parking brake is applied automatically while it is in operation.

• Appears if the automatic brake hold is automatically canceled while it is in operation.

•  Immediately depress the brake pedal.

• Appears when the electric parking brake switch is pulled without depressing the brake pedal while the electric parking brake is in operation.

• Pull the electric parking brake switch with the brake pedal depressed.
  Parking Brake P. 545

•  Appears when you set the power mode to VEHICLE OFF, if the rear doors were opened shortly before or after the vehicle was powered on.

• Appears as soon as a problem is detected in the keyless access system or keyless starting system.

• Appears constantly – Have your vehicle checked by a dealer.

• Appears when you close the door with the power mode in ON without the keyless remote inside the vehicle.

• Disappears when you bring the keyless remote back inside the vehicle and close the door.
  Keyless Remote Reminder P. 195

•  Appears when the keyless remote battery becomes weak.

• Appears after you set the power mode to ACCESSORY or ON.

Canadian models

• Appears after you unlock and open the driver’s door.

• Appears when the engine does not restart automatically due to the following reasons:
  • The hood is open.
  • There is a problem in the system that disables Auto Idle Stop.

• Follow the normal procedure to start the engine.
  Starting the Engine P. 443

•  Appears after the driver’s door is opened when the power mode is in ACCESSORY.

• Change the power mode to VEHICLE OFF. ENGINE START/STOP Button P. 193

• Appears when the power mode is in ACCESSORY.

•  Appears if the keyless remote’s battery is too weak to start the engine or the key is not within operating range to start the engine.
  The beeper sounds six times.

•  Bring the back of the keyless remote into contact with the ENGINE START/STOP button.
  If the Keyless Remote Battery is Weak P. 665

• Appears if you press the ENGINE START/STOP button while the vehicle is moving.

• Appears after the driver’s door is opened when the power mode is in ACCESSORY.

• Press and hold the ENGINE START/STOP button with your foot off the brake pedal to change the power mode to VEHICLE OFF.

• Appears when you turn the Auto Idle Stop system on.

•  Appears when the hood is opened.

• Close the hood.

Canada

•  Appears when the (P button is pressed while the vehicle is moving.

• Make sure that the vehicle comes to a stop before operating the select button.

• Appears if you put the transmission into (R while the vehicle is moving forward, or into (D while the vehicle is reversing.

•  Appears when you set the power mode to OFF while driving.

• Immediately stop in a safe place, set the parking brake, then restart the engine. If the message disappears, continue driving.

•  Appears when the vehicle is stopped with the driver’s seat belt unfastened and there is a chance that the vehicle may roll unintentionally.

• Press the (P button before release the brake pedal when idling, parking or exiting the vehicle.
  Shift Operation P. 453

• Appears when you attempt to change to another gear position with the transmission in (P and the engine OFF.

• To select another gear position while in (P, the engine must be ON.

•  Appears when you press the (P button but it is not engaged due to low ATF temperature.

• Depress the brake pedal until this message disappear.

• Appears when the temperature of the transmission is starting to get too hot.
• The performance of the vehicle may be reduced.

• Until the message disappears, reduce your speed and allow the system to cool down.

•  Appears when you repeatedly change the shift position between (P and other positions in short period.

• Take some time before changing the shift position.

• Appears when you try to take the transmission out of (P immediately after you start engine.

• Try to take the transmission out of (P again.

• Appears when you depress the accelerator pedal when the transmission is in (N.

• Remove your foot off the accelerator pedal. When driving, depress the brake pedal and operate the shift position.

• Appears when you press and hold (N button for more than two seconds.

• Disappears when you set the shift position to other than (N. If you want to keep the transmission in (N position [car wash mode] P. 455

• Appears for a few seconds if you have not pressed the (N button long enough to initiate Neutral-Hold mode.

• Appears when neutral hold mode is not available due to the transmission being too hot.

• When the transmission is too hot, neutral hold mode may not be available. Let the engine idle until the transmission has cooled down.
  If you want to keep the transmission in (N position [car wash mode] P. 455

• Appears if there is a problem with the auto high- beam.

• Manually operate the headlight switch.
• If you are driving with the high-beam headlights when this happens, the headlights are changed to low beams.

•  Appears when ACC has been automatically canceled.

• You can resume the set speed after the condition that caused ACC to cancel improves. Press the RES/+ button.
  Adaptive Cruise Control (ACC) with Low Speed Follow P. 502

• Flashes when the system senses a likely collision with a vehicle in front of you. The beeper sounds.

• Take appropriate action to prevent a collision (apply the brakes, change lanes, etc.
  Collision Mitigation Braking SystemTM (CMBSTM)
  P. 486

Adaptive Cruise Control (ACC) with Low Speed Follow P. 502
Models with Low Speed Braking Control
Low Speed Braking Control*P. 502

•  Appears when the low speed braking control system is activated.

• Appears when ACC is canceled due to excessive high vehicle speed.

• Reduce the speed, then reset ACC.
  Adaptive Cruise Control (ACC) with Low Speed Follow P. 502

•  Appears when cruise control is canceled due to excessive low vehicle speed.

•  Raise the speed, then reset cruise control.
  To Switch ACC with Low Speed Follow to Cruise Control P. 518

• Appears when the speed of the vehicle is too high for you to set ACC.

•  Reduce the speed, then set ACC.
  Adaptive Cruise Control (ACC) with Low Speed Follow P. 502

•  Appears when the speed of the vehicle is too low for you to set cruise control.

•  Raise the speed, then set cruise control.
  To Switch ACC with Low Speed Follow to Cruise Control P. 518

•  Appears when the distance between your vehicle and the vehicle ahead of you is too close while ACC is in operation.

• ACC has been automatically canceled.
  Adaptive Cruise Control (ACC) with Low Speed Follow P. 502

• Appears when pressing the RES/+ or SET/– button while the distance between your vehicle and the vehicle ahead of you is too close.

• ACC cannot be set.
  Adaptive Cruise Control (ACC) with Low Speed Follow P. 502

• Appears when the parking brake is applied automatically while ACC is in operation.

• ACC has been automatically canceled.
  Adaptive Cruise Control (ACC) with Low Speed Follow P. 502
  Parking Brake P. 545

• Appears when pressing the RES/+ or SET/– button while the parking brake is applied.

• ACC cannot be set.
  Adaptive Cruise Control (ACC) with Low Speed Follow P. 502
  Parking Brake P. 545

• Appears if ACC is canceled while your vehicle is automatically stopped by ACC.

• Immediately depress the brake pedal.

•  Appears when pressing the

RES/+ or SET/– button while the vehicle is moving and the brake pedal is depressed.

• ACC cannot be set.
  Adaptive Cruise Control (ACC) with Low Speed Follow P. 502

• Appears if the VSA® or traction control function operates while ACC is in operation.

• ACC has been automatically canceled.
  Adaptive Cruise Control (ACC) with Low Speed Follow P. 502

• Appears if ACC cannot be set due to repeated deceleration, driving on a long downward slope, or excess vehicle weight.

• Wait awhile, then reset ACC.
  Adaptive Cruise Control (ACC) with Low Speed Follow P. 502

• Appears just before the ACC is automatically canceled due to repeated deceleration, driving on a long downward slope, or excess vehicle weight. (Will automatically open until the distance between your vehicle and the vehicle ahead is the maximum set in distance settings.)
• Appears when the ACC has been automatically canceled.

• Appears when SET/–, RES/+, CANCEL, or interval button is pressed while ACC is off.

• Appears when interval button is pressed while Cruise mode is selected.

• After selecting ACC, press the interval button.
  Adaptive Cruise Control (ACC) with Low Speed Follow P. 502

• Appears when the vehicle ahead of you resumes driving, after your vehicle has been stopped automatically by ACC.

• Press the RES/+ or SET/– button or depress the accelerator pedal to resume.
  Adaptive Cruise Control (ACC) with Low Speed Follow P. 502

• Appears when the driver’s seat belt is unfastened while your vehicle is automatically stopped by ACC.

• ACC has been automatically canceled.
  Adaptive Cruise Control (ACC) with Low Speed Follow P. 502

• Appears when pressing the RES/+ or SET/– button while the driver’s seat belt is unfastened.

• ACC cannot be set. Adaptive Cruise Control (ACC) with Low Speed Follow P. 502

• Appears when the transmission is put into any position other than (D or (S while ACC is in operation.

•  ACC has been automatically canceled. Adaptive Cruise Control (ACC) with Low Speed Follow P. 502

• Appears when pressing the RES/+ or SET/– button while the transmission is in any position other than (D or (S.

• ACC cannot be set.
  Adaptive Cruise Control (ACC) with Low Speed Follow P. 502

• Appears when the vehicle is stopped on a very steep slope while ACC is in operation.

• ACC has been automatically canceled. Adaptive Cruise Control (ACC) with Low Speed Follow P. 502

• Appears when pressing the RES/+ or SET/– button while the vehicle is stopped on a very steep slope.

• ACC cannot be set. Adaptive Cruise Control (ACC) with Low Speed Follow P. 502

• Appears if anything covers the radar sensor cover and prevents the sensor from detecting a vehicle in front.
• May appear when driving in bad weather (rain, snow, fog, etc.)

• When the radar sensor gets dirty, stop your vehicle in a safe place, and wipe off dirt using a soft cloth. The message may take some time to go off.
• Have your vehicle checked by a dealer if the message does not disappear even after you clean the sensor cover.

Radar Sensor P. 543
AcuraWatchTM P. 483

• Use the climate control system to cool down the camera.
• Disappears – The camera has been cooled down and the systems are activated normally.

Front Sensor Camera P. 541
AcuraWatchTM P. 483

• When the front window gets dirty, stop your vehicle in a safe place, and wipe it off with a soft cloth.
• Have your vehicle checked by a dealer if the message does not disappear even after you cleaned the area around the camera.

Front Sensor CameraP. 541
AcuraWatchTM P. 483

• Blinks when you fail to steer the vehicle. The beeper sounds simultaneously.

• Operate the steering wheel to resume the LKAS.

• Appears when the vehicle is driving out of a detected lane. The steering wheel vibrates rapidly.

• Keep the vehicle within the lane you are driving.

Lane Keeping Assist System (LKAS) P. 522

• Appears when the vehicle is driving out of a detected lane.
  When you selected Warning Only

• The steering wheel vibrates rapidly when the vehicle is drifting out of a detected lane.
  When you selected Normal, Wide or Narrow
• The steering wheel vibrates rapidly when the vehicle is drifting out of a detected lane. The system also steers the vehicle to help you remain within your driving lane.

•  Keep the vehicle within the lane you are driving.

Road Departure Mitigation System P. 530

• You can change the setting for the road departure mitigation system. Normal, Wide, Warning Only and Narrow can be selected.
  Customized Features P. 359