2024 Alfa Romeo Tonale Fuses and Fuse Box Owner’s Manual
The fuse box system of the 2024 Alfa Romeo Tonale is streamlined and perfectly blends into the car’s elegant exterior. The efficient fuse box improves accessibility without sacrificing the vehicle’s visual beauty. Integrating cutting-edge fusing technology guarantees both top performance and road safety.
2024 Alfa Romeo TONALE Specs, Price, Features, Mileage And Review
Alfa Romeo FUSES Guide
General Information
WARNING!
- When replacing a blown fuse, always use an appropriate replacement fuse with the same amp rating as the original fuse. Never replace a fuse with another fuse of a higher amp rating. Never replace a blown fuse with metal wires or any other material. Do not place a fuse inside a circuit breaker cavity or vice versa. Failure to use proper fuses may result in serious personal injury, fire and/or property damage.
- Before replacing a fuse, make sure that the ignition is off and that all the other services are switched off and/or disengaged.
- If the replaced fuse blows again, contact an authorized dealer.
- If a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, transmission system) or steering system blows, contact an authorized dealer.
The fuses protect electrical systems against excessive current.
When a device does not work, you must check the fuse element inside the blade fuse for a break/melt.
Also, please be aware that using power outlets for extended periods with the engine off may result in vehicle battery discharge.
Blade Fuses
- Fuse Element
- Blade Fuse with a good/functional fuse element 3 — Blade Fuse with a bad/not functional fuse element (blown fuse)
Power Distribution Center/Fuses And Relays
The Front Power Distribution Center is located in the engine compartment. This module contains fuses and relays. Fuse cavity locations are printed on the inside of the power distribution centre cover.
CAUTION!
When installing the power distribution centre cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution centre and possibly result in an electrical system failure.
Underhood Power Distribution Location
Underhood Power Distribution Location
The fuse box screw and cover must be removed to gain access to the fuses.
Fuse Box Cover And Locking Screw Removal
- Fuse Cover
- Locking Screw
For fuse box access, proceed as follows:
- Turn the locking screw counterclockwise.
- Slowly release the screw.
- Remove the fuse box cover by sliding it upward.
- Reverse the procedure to reinstall.
Main Fuse Block — Gasoline Engine
| Cavity | Cartridge Fuse | Maxi Fuse | Mini Fuse | Description |
| * If Equipped | ||||
| F01 | – | 70 Amp Tan | – | BCM1 |
| F02 | – | 70 Amp Tan | – | BCM2 / RDU |
| F03 | 20 Amp Blue | – | – | BCM3 |
| F04 | 40 Amp Green | – | – | BCM Valves |
| F05 | – | – | – | Not Used |
| F06 | – | 20 Amp Yellow | – | Front Wiper Motor |
| F07 | – | 20 Amp Yellow | – | DTCM |
| F08 | 30 Amp Pink | – | – | Power Supply F24 – F87 – Fxx |
| F09 | – | – | 7.5 Amp Brown | ECM T09 |
| F10 | – | – | 15 Amp Blue | Horn |
| F11 | – | – | 5 Amp Tan | Engine Secondary Loads |
| F14 | – | – | 7.5 Amp Brown | LTR |
| F15 | – | 40 Amp Orange | – | BSM Pump |
| F16 | – | – | 10 Amp Red | ECM / TCM / AGSM |
| F17 | – | – | 10 Amp Red | ECM |
| F18 | – | – | – | Spare |
| F19 | – | – | 7.5 Amp Brown | A/C Compressor |
| F20 | – | – | 15 Amp Blue | RR Cargo Power Outlet |
| F21 | – | – | 20 Amp Yellow | Fuel Pump |
| F22 | – | – | 15 Amp Blue | ECM |
| F23 | – | – | 5 Amp Tan | USB / Aux Outlet |
| F24 | – | – | 10 Amp Red | DTCM |
| F30 | – | – | 5 Amp Tan | AWD DTCM |
| F81 | – | 30 Amp Green | – | Brake Booster Vacuum Pump |
| F82 | – | – | – | Spare |
| F83 | 40 Amp Green | – | – | HVAC Fan |
| F84 | – | – | 7.5 Amp Brown | Rad Fan Enable |
| F87 | – | – | 5 Amp Tan | AGSM |
| F88 | – | – | 7.5 Amp Brown | Heated Mirrors & Washer Nozzle |
| F89 | 30 Amp Pink | – | – | Rear Window Defrost |
| F90 | – | – | 5 Amp Tan | Intelligent Battery Sensor |
Main Fuse Block — Hybrid
| Cavity | Cartridge Fuse | Maxi Fuse | Mini Fuse | Description |
| * If Equipped | ||||
| F01 | – | 70 Amp Tan | – | BCM1 |
| F02 | – | 70 Amp Tan | – | BCM2 / RDU |
| F03 | 20 Amp Blue | – | – | BMC3 |
| F04 | 40 Amp Green | – | – | BCM Valves |
| F05 | – | 40 Amp Orange | – | PTC 1 |
| F06 | – | 20 Amp Yellow | – | Front Wiper Motor |
| F07 | – | 50 Amp Red | – | AUX 1 RDU |
| F08 | 30 Amp Pink | – | – | Power Supply F24 – F87 – Fxx |
| F09 | – | – | 7.5 Amp Brown | ECM T09 |
| F10 | – | – | 15 Amp Blue | Horn |
| F11 | – | – | 5 Amp Tan | Engine Secondary Loads |
| F14 | – | – | – | Spare |
| F15 | – | 70 Amp Tan | – | BSM Pump |
| F16 | – | – | 10 Amp Red | ECM / TCM / AGSM |
| F17 | – | – | 10 Amp Red | GPF – HV Fuel lid – HV Fuel Tank
Isolation Valve |
| F19 | – | – | 7.5 Amp Brown | A/C Compressor |
| F20 | – | – | 15 Amp Blue | RR Cargo Power Outlet |
| F21 | – | – | 20 Amp Yellow | Fuel Pump |
| F22 | – | – | 20 Amp Yellow | Engine Primary Loads |
| F23 | – | – | 5 Amp Tan | AGS/ USB / Aux Outlet |
| F24 | – | – | 10 Amp Red | TCM |
| F30 | – | – | – | Spare |
| F81 | – | 40 Amp Orange | – | AUX 2 RDU |
| F82 | 40 Amp Green | – | – | External Oil Pump (AT) |
| F83 | 40 Amp Green | – | – | HVAC Fan |
| F84 | – | – | – | Spare |
| F87 | – | – | 5 Amp Tan | AGSM |
| F88 | – | – | 7.5 Amp Brown | Heated Mirrors & Washer Nozzle |
| F89 | 30 Amp Pink | – | – | Rear Window Defrost |
| F90 | – | – | 5 Amp Tan | Intelligent Battery Sensor |
| Fxx | – | – | 25 Amp Clear | EPT_PIM_Feed_2 |
Relays — Gasoline Engine
| Cavity | Maxi Fuse | Mini Fuse | Description |
| T02 | – | – | Not Used |
| T03 | – | 30 Amp | Horn |
| T05 | – | 30 Amp | A/C Compressor |
| T06 | – | 30 Amp | Rad Fan Enable |
| T08 | – | 30 Amp | HVAC Fan |
| T10 | – | – | Not Used |
| T14 | – | 30 Amp | RR Cargo Power Outlet |
| T19 | – | – | Not Used |
| T20 | – | 30 Amp | Starter Relay R1 |
| T31 | – | 30 Amp | Fuel Pump |
| T89 | – | – | Not Used |
| T90 | – | 30 Amp | Brake Booster Vacuum Pump |
Relays — Hybrid
| Cavity | Maxi Fuse | Mini Fuse | Description |
| T02 | – | – | Not Used |
| T03 | – | 30 Amp | Horn |
| T05 | – | 30 Amp | A/C Compressor |
| T06 | – | 30 Amp | Rad Fan Enable |
| T07 | 50 Amp | – | Aux.1 |
| T08 | – | 30 Amp | HVAC Fan |
| T09 | – | 30 Amp | Engine Main Relay |
| T10 | – | – | Not Used |
| T14 | – | 30 Amp | Rear Cargo Power Outlet |
| T17 | – | 30 Amp | Rear Window Defrost/Heated Mirrors |
| T19 | – | 30 Amp | External Oil Pump |
| T20 | – | 30 Amp | Starter Relay R1 |
| T31 | – | 30 Amp | Fuel Pump |
| T89 | – | – | Not Used |
| T90 | – | 30 Amp | Brake Booster Vacuum Pump |
Supplemental Fuse Box — Hybrid
| Cavity | Mini Fuse | Description |
| F01 | 5 Amp Tan | Electric Air Heater (EAH) |
| F02 | 7.5 Amp Brown | Electric Air Compressor (EAC) |
| F03 | 5 Amp Tan | Integrated Dual Charge Module (IDCM) |
| F04 | 5 Amp Tan | Charge Port Indicator Module (CPIM) |
| F05 | 15 Amp Blue | Power Electronic Coolant Pump 2 (PECP2) |
| F06 | 15 Amp Blue | Power Electronic Coolant Pump (PECP) |
| F07 | 5 Amp Tan | Aux Heater Pump (AHP) |
| F08 | 5 Amp Tan | PIM Feed 1 |
| F09 | 10 Amp Red | BPCM Feed 1 |
| F10 | 5 Amp Tan | PIM Feed 3 |
| F11 | 10 Amp Red | BPCM Feed 2 |
| F12 | 5 Amp Tan | Electronic Pedestrian Protection Module (EPPM) |
Interior Fuses
The interior fuse panel is located under the driver’s side lower instrument panel.
| Cavity | Mini Fuse | Description |
| *If Equipped | ||
| F31 | 7.5 Amp Brown | HVAC relay coil / Power Outlet / Seats Movement Relay Coil |
| F33 | 20 Amp Yellow | Front Passenger Window Lifter |
| F34 | 20 Amp Yellow | Front Driver Window Lifter |
| F36 | 15 Amp Blue | HVAC / VTA / External Mirror /Ceiling Light / CVPM / Radio Mod / USB / AUX/ DCSD /
Electric Steering Lock |
| F37 | 10 Amp Red | Brake Switch / DASM / IPC |
| F38 | 20 Amp Yellow | Central Door Lock / Doors Unlock / Decklid / Liftgate |
| F42 | 7.5 Amp Brown | BSM / EPS |
| F43 | 20 Amp Yellow | Bi-Directional Washer Pump |
| F47 | 20 Amp Yellow | The Rear Left Window Lifter |
| F48 | 20 Amp Yellow | Rear Right Window Lifter |
| F49 | 7.5 Amp Brown | PAM / RLS / Power Internal Mirror / Heated Seats Relay Coil / USB Charger / WCPM /
DTV / ESL / HCPM |
| F50 | 7.5 Amp Brown | ORC |
|
F51 |
7.5 Amp Brown |
HCP / Reverse Gear / Filter Diesel SNSR / A/C Compressor / HVAC / Defrosting /
Right Headlamp Leveling / Left Headlamp Leveling / LDW / Alarm Mod / Airbag Psg / PIM / Trailer Tow Mod / AFLM / Air Quality Sensor / ASBM / Headlamp Leveling |
| F53 | 7.5 Amp Brown | ALU / EPB / BrakePedalSW NO / EMCM / TBM / DSCM / IPC |
| F94 | 15 Amp Blue | Power Outlet |
2024 Alfa Romeo TONALE Specs, Price, Features, Mileage And Review
Rear Cargo Fuse/Relay Distribution Unit— If Equipped
To access the fuses, remove the access door from the left rear panel in the rear cargo area.
The fuses may be contained in two units. Fuse Holder No. 1 is located closest to the rear of the vehicle and Fuse Holder No. 2 (If equipped with trailer towing) is located closest to the front of the vehicle.
- Fuse Holder No. 1
- Fuse Holder No. 2
Fuse Holder No. 1
| Cavity | Mini Fuse | Description |
| * If Equipped | ||
| F1 | 20 Amp Yellow | Sunroof* |
| F2 | – | – |
| F3 | 30 Amp Green | Power Liftgate Module (PLGM) |
| F4 | 5 Amp Tan | Driver And Passenger Ventilated Seats (HMSM*) |
| F5 | 25 Amp Clear | Heating And Memory Drive Seat Module 1 |
| F6 | 10 Amp Red | Heating And Memory Drive Seat Module 2 |
| F7 | 7.5 Amp Brown | Driver And Passenger Lumbar Regulator (Without
HMSM) |
| F8 | 20 Amp Yellow | Passenger Seat SW (HMSM*) |
Fuse Holder No. 2
| Cavity | Mini Fuse | Description |
| F3 | 5 Amp Tan | Hands-Free Power Liftgate (HFRM) |
| F4 | 7.5 Amp Brown | Damping Control Module |
| F5 | 5 Amp Tan | Changeover Valve Feed (ELCM) |
| F8 | 7.5 Amp Brown | Damping Control Module |
On the Rear Cargo Fuse/Relay Distribution Unit bracket, there is a Maxi Fuse holder for the Amplifier (if equipped).
| Cavity | Maxi Fuse | Description |
| * If Equipped | ||
| F01 | 30 Amp Green | Amplifier* |
How to replace the Fuse of the 2024 Alfa Romeo Tonale
Replacing a fuse in a car is typically a straightforward process, but it’s important to follow the correct steps to ensure safety and avoid damaging your vehicle. Here’s a general guide on how to replace a fuse in a 2024 Alfa Romeo Tonale:
Materials:
- The new fuse of the correct amperage.
- Fuse puller or needle-nose pliers.
Instructions:
-
Locate the Fuse Box: The fuse box in most cars, including the Alfa Romeo Tonale, is usually located under the dashboard on the driver’s side or in the engine compartment.
-
Identify the Blown Fuse: Once you’ve located the fuse box, open the cover. Inside, you’ll find a diagram that indicates which fuse corresponds to each electrical component in your vehicle. Look for the fuse that corresponds to the malfunctioning component. A blown fuse will have a broken wire inside or a discoloured appearance.
-
Turn Off the Ignition: Before you replace the fuse, turn off the ignition and any electrical components associated with the fuse you’re replacing. This prevents any potential electrical surges or short circuits.
-
Remove the Blown Fuse: Using a fuse puller tool or a pair of needle-nose pliers, carefully grasp the blown fuse and pull it straight out of its slot. Be gentle to avoid damaging the fuse box or surrounding components.
-
Insert the New Fuse: Take a new fuse of the same amperage rating as the blown one. Make sure it’s the correct type and rating to prevent electrical issues or damage to your vehicle. Align the new fuse with the terminals inside the fuse box and push it firmly into place.
-
Close the Fuse Box: Once you’ve replaced the fuse, close the fuse box cover securely.
-
Test the Electrical Component: Turn on the ignition and test the electrical component associated with the fuse you replaced to ensure it’s functioning properly.
-
Dispose of the Old Fuse: Properly dispose of the blown fuse. You can usually discard it with household waste.
-
Keep Spare Fuses: It’s a good idea to keep a variety of spare fuses in your car in case of future emergencies.
Tips:
- Always use a fuse with the correct amperage rating to prevent electrical issues or damage to the vehicle.
- If a fuse blows repeatedly, it may indicate an underlying electrical problem and professional assistance may be needed.
FAQs
The fuse box in the 2024 Alfa Romeo Tonale serves as a centralized location for electrical fuses, which protect various circuits in the vehicle from electrical overloads.
The exact number may vary slightly, but typically, the fuse box in the 2024 Alfa Romeo Tonale contains around 20 fuses.
The fuse box is usually located in a readily accessible area of the vehicle, often beneath the dashboard or in the engine compartment.
The 2024 Alfa Romeo Tonale commonly uses blade-type fuses, which are easy to identify and replace.
To access the fuse box, you typically need to open the fuse box cover, which may require using a screwdriver or simply pressing a release button, depending on the vehicle’s design.
Generally, replacing a fuse in the 2024 Alfa Romeo Tonale requires minimal tools, often just a pair of needle-nose pliers or a fuse puller.
A blown fuse is often visually identifiable by a break in the metal strip inside the fuse. Additionally, you can use a multimeter to check for continuity.
Fuses in the 2024 Alfa Romeo Tonale typically have varying amperage ratings, depending on the circuit they protect. Common amperages range from 5A to 30A.
The fuses in the 2024 Alfa Romeo Tonale protect various electrical circuits, including those for the headlights, windshield wipers, power windows, and audio system, among others.
It is not recommended to use a fuse with a higher amperage rating than specified, as this can lead to damage to the vehicle’s electrical system or even pose a fire hazard.
The fuse box cover typically contains a diagram or label indicating which fuse protects which circuit. Additionally, the vehicle’s owner’s manual provides this information.
Some vehicles may come equipped with spare fuses stored within the fuse box or elsewhere in the vehicle.
It’s a good idea to periodically check the fuses in your 2024 Alfa Romeo Tonale, especially if you’re experiencing electrical issues with the vehicle.
When working with the electrical system and fuses, it’s essential to disconnect the vehicle’s battery to avoid the risk of electrical shock or damage to components.
Extreme temperatures can potentially affect the performance of fuses in any vehicle, including the 2024 Alfa Romeo Tonale. It’s essential to ensure that the fuse box is adequately sealed and protected from environmental conditions.
Common issues related to the fuse box in the 2024 Alfa Romeo Tonale include blown fuses due to electrical faults or overloads, as well as corrosion or loose connections.