Alfa Romeo Giulia 2022 Warning lights

When it comes to car safety, the 2022 Alfa Romeo Giulia is on guard with a full warning system that is meant to keep drivers aware and safe. The dashboard of the Giulia is set up with a wide range of warning lights that each serve as a beacon of information about the car’s state. From the “Check Engine” light to the “Tire Pressure Monitoring System” (TPMS) light, these lights come on to let drivers know about possible problems that need to be fixed. With different colors to show how bad the situation is, these warning lights act as a proactive guardian, making sure that cars know what’s going on and can act quickly. Alfa Romeo’s commitment to safety is shown by the 2022 Giulia’s complex network of warning lights, which give drivers the tools they need to deal with possible problems and keep driving safe and confident.

WARNING LIGHTS

WARNING LIGHTS AND MESSAGES ON THE INSTRUMENT PANEL
The following pages consist of warning lights and messages.
NOTE:

• The warning light turns on together with a dedicated message and/or chime when applicable. These indications are precautionary and as such must not be considered as exhaustive and/or alternative to the information contained in the Owner’s Manual, which you are advised to read carefully in all cases. Always refer to the information in this section in the event of a failure indication.
• The failure indicators appearing on the display are divided into two categories: very serious and less serious faults. Serious faults are indicated by a repeated and prolonged warning “cycle.” Less serious faults are indicated by a warning “cycle” with a shorter duration. You can stop the warning cycle in both cases by pushing the button located on the windshield wiper stalk. The instrument panel warning light will stay on until the cause of the failure is eliminated.

RED WARNING LIGHTS

Air Bag Warning Light
This warning light will illuminate to indicate a fault with the airbag, and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ON/RUN position. This light will illuminate with a single chime when a fault with the air bag has been detected, it will stay on until the fault is cleared. If the light is either not on during startup, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.
Brake Warning Light
This warning light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected.
NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is necessary.

WARNING!

• The fault of the warning light is signaled by the turning on of the icon on the instrument panel. In this case, the warning light may not indicate any faults with the restraint systems. Before proceeding, contact an authorized dealer to have the system checked immediately.
• If the warning light does not turn on when the ignition device is moved to ON or if it stays on when driving (together with the message on the display), there might be a fault in the restraint systems; in this case, the air bags or pretensioners may not deploy in the event of an accident or, in a lower number of cases, they could deploy erroneously. Before proceeding, contact an authorized dealer to have the system checked immediately.

Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.

NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application.

Seat Belt Reminder Warning Light
When the ignition is first placed in the ON/RUN position, if the driver’s seat belt is unbuckled, a chime will sound and the light will turn on. When driving, if the driver or front passenger seat belt remains unbuckled, the Seat Belt Reminder Light will flash or remain on continuously and a chime will sound.

WARNING!

• The fault of the warning light is signaled by the turning on of the icon on the instrument panel. In this case, the warning light may not indicate any faults with the restraint systems. Before proceeding, contact an authorized dealer to have the system checked immediately.
• If the warning light does not turn on when the ignition device is moved to ON or if it stays on when driving (together with the message on the display), there might be a fault in the restraint systems; in this case, the air bags or pretensioners may not deploy in the event of an accident or, in a lower number of cases, they could deploy erroneously. Before proceeding, contact an authorized dealer to have the system checked immediately.

Electronic Brake Force Distribution (EBD) Failure

The simultaneous turning on of the BRAKE (red) and (amber) warning lights with the engine on indicates either a failure of the EBD system or that the system is not available. In this case, the rear wheels may suddenly lock and the vehicle may swerve when braking abruptly. Drive very carefully to the nearest authorized dealer to have the system inspected immediately.

Oil Temperature Warning Light
This telltale indicates engine oil temperature is high. Stop the vehicle and shut off the engine as soon as possible. If the problem persists, contact an authorized dealer.

AMBER WARNING LIGHTS

Anti-Lock Brake System (ABS) Warning Light
This light monitors the ABS. The light will turn on when the ignition is placed in the ON/RUN position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required. However, the conventional brake system will continue to operate normally if the brake indicator light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes. If the ABS light does not turn on when the ignition is placed in the ON/ RUN position, have the light inspected by an authorized dealer.

Electronic Stability Control (ESC) Indicator Light — If Equipped

When the ignition is cycled to ON, the indicator light illuminates but should turn off as soon as the engine is started.

• ESC System Intervention: Intervention by the system is indicated by the flashing of the indicator light: it indicates that the vehicle is in critical stability and grip conditions.
• ESC System Failure: If the indicator light does not turn off, or if it stays on with the engine running, a failure was found in the ESC system.
• Hill Start Assist System Failure: The illumination of the indicator light indicates a Hill Start Assist system failure. In these cases, contact an authorized dealer as soon as possible.

Electronic Stability Control (ESC) OFF Indicator Light — If Equipped

When the ignition is cycled to ON, the indicator light illuminates, but should turn off as soon as the engine is started. The indicator light illuminates to indicate that some active safety systems have been partially or totally deactivated. When the active safety systems are reactivated, the indicator light turns off.

Tire Pressure Low Warning Light

The indicator light will illuminate to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tire duration and fuel consumption may not be guaranteed. In any situation in which the message on the display is “See Manual” .

Tire Pressure Monitoring System (TPMS) Warning Light

The warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tire duration and fuel consumption may not be guaranteed. Should one or more tires be in the condition mentioned above, the display will show the indications corresponding to each tire.
CAUTION! Do not continue driving with one or more flat tires as handling may be compromised. Stop the vehicle, avoiding sharp braking and steering. If a tire puncture occurs, repair immediately using the dedicated tire repair kit and contact an authorized dealer as soon as possible. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires. As an added safety feature, your vehicle has been equipped with a TPMS that illuminates a low tire pressure telltale when one or more of your tires is significantly underinflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly underinflated tire causes the tire to overheat and can lead to tire failure. Underinflation also reduces fuel efficiency and tire tread life and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if underinflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.

WARNING!
The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Using aftermarket tire sealants may cause the Tire Pressure Monitoring System (TPMS) sensor to become inoperable. After using an aftermarket tire sealant it is recommended that you take your vehicle to an authorized dealership to have your sensor function checked.

Rear Fog Lights
The indicator illuminates when the rear fog light is activated.

Engine Check/Malfunction Indicator Light (MIL)
In normal conditions, when the ignition is cycled to ON, the indicator light illuminates, but it should turn off as soon as the engine is started. The operation of the indicator light may be checked by the traffic police using specific devices. Comply with the laws and regulations of the country where you are driving. Under these conditions, the vehicle can continue traveling at a moderate speed but without demanding excessive effort from the engine or high speed. Prolonged use of the vehicle with the indicator light on constantly may cause damage. Contact an authorized dealer as soon as possible.

CAUTION! If, turning the ignition device to ON, the warning light does not turn on or if it turns on steadily or is flashing when traveling (on some versions together with the message on the display), contact an authorized dealer as soon as possible.

Forward Collision Warning (FCW) System
This indicator light informs the driver that the frontal collision alarm function is not enabled. Drive carefully and contact an authorized dealer as soon as possible.

Fuel Reserve/Limited Range
The indicator light (or the symbol in the display) illuminates when about 2.4 gallons (9 liters) of fuel is left in the tank.

WARNING! If the warning light (or the icon on the display) flashes while driving, contact an authorized dealer.

GREEN INDICATOR LIGHTS

Automatic High Beam Indicator Light — If Equipped
This indicator light will illuminate when the automatic high-beam headlights are activated.
Left Turn Signal Indicator Light
The instrument cluster directional arrow will flash independently for the left turn signal as selected, as well as the exterior turn signal lamp(s) (front and rear) as selected when the multifunction lever is moved down (left). This directional arrow will flash in conjunction with the right directional arrow when the hazard warning light button is pushed.
Parking/Headlights On Indicator Light
This indicator will illuminate when the parking lights or headlights are turned on.

Right Turn Signal Indicator Light
The instrument cluster directional arrow will flash independently for the right turn signal as selected, as well as the exterior turn signal lamp(s) (front and rear) as selected when the multifunction lever is moved up (right). This directional arrow will flash in conjunction with the left directional arrow when the hazard warning light button is pushed.

BLUE INDICATOR LIGHTS

High Beam Indicator Light — If Equipped
This indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Push the lever a second time to switch the headlights back to low beam. Pull the lever toward you for a temporary high beam on, “flash to pass” scenario.

RED SYMBOLS

Alfa Steering Torque (AST) Failure
The switching on of the telltale signals a failure in the automatic steering correction system. Contact an authorized dealer to have the system checked.
Alternator Failure
The switching on of the telltale with engine on corresponds to an alternator failure. Contact an authorized dealer as soon as possible.

Automatic Transmission Failure
The telltale turns on, together with a buzzer warning, to indicate that the automatic transmission is faulty. Contact an authorized dealer as soon as possible.

CAUTION!
Driving the vehicle with this symbol on may severely damage the gearbox, with resulting breakage. The oil may also overheat: contact with hot engine or with exhaust components at high temperature could cause fires.

Brake Disc Temperature
When the symbol turns on, it indicates an excessive temperature of the brake discs. Let the breaking system cool down by reducing the speed.

Driver Attention Assist (DAA) System Activation

The symbol appears, together with a message on the display, in case of activation of the DAA system. Stop to pause while driving, pulling the car over in safe conditions.

Door Open

The telltale turns on when one or more doors are not completely shut. An acoustic signal is activated with the doors open and the car moving. Close the doors properly.

Power Steering Failure

If the telltale remains on, you may not have steering assistance and the effort required to operate the steering wheel may be increased; steering is, however, possible.

NOTE:
After the battery is disconnected, the steering wheel must be initialized. The Power Steering Failure light on the instrument panel will illuminate to indicate this. To carry out this procedure, simply turn the steering wheel all the way from  one end to the other, and then turn it back to thecentral position. Contact an authorized dealer as soon as possible.

Electronic Throttle Control (ETC) Warning Light

This warning light, along with the related message, signals a failure in the ETC. If a failure is detected, the warning light turns on while the engine is running. Place the gear selector in the PARK (P) position and the ignition in the off position: the warning light should switch off. If the warning light stays on with engine running, the vehicle can still be driven. If the warning light flashes with the engine running, immediate intervention is required. A  loss of performance, irregular/high idling speed or engine stopping might take place and the vehicle may need to be towed. Contact an authorized dealer as soon as possible to have the failure eliminated.

Engine Coolant Temperature Too High
The telltale lights up when the engine has overheated. In normal driving conditions: stop the car, turn off the engine and check that the coolant level in the reservoir is not below the MIN mark. In this case, wait for the engine to cool down, then slowly and carefully open the cap, fill with coolant and check that the level is between the MIN and MAX marks on the reservoir itself. Also check visually for any fluid leaks. Contact an authorized dealer if the telltale comes on when the engine is started again. If the vehicle is used under demanding conditions (e.g. in high-performance driving): slow down and, if the warning light stays on, stop the vehicle. Stop for two or three minutes with the engine running and slightly accelerated to facilitate  better coolant circulation, then turn the engineoff. Check that the coolant level is correct as described above

Hood Cap Not Properly Shut
The telltale turns on when the hood cap is not properly closed, along with the icon, an image of the vehicle with an open hood cap appears on the display. A buzzer is heard when the hood cap is open and the vehicle is moving. Close the hood properly.

Insufficient Engine Oil Level
The telltale turns on, along with the related message on the display, to  indicate low engine oil level.Contact an authorized dealer to have the system checked.

Low Engine Oil Pressure
This telltale indicates low engine oil pressure. If the telltale turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this telltale turns on. Do not operate the vehicle until the cause is corrected. This telltale does not indicate how much oil is in the engine.
NOTE: Do not use the vehicle until the failure has been solved. The turning on of the telltale does not indicate the amount of oil in the engine: the oil level can be checked on the display upon entering the vehicle and also by activating the “Oil level” function on the Information and Entertainment System. Contact an authorized dealer as soon as possible.

CAUTION! If the LOW ENGINE OIL PRESSURE symbol switches on when driving, stop the engine immediately and contact an authorized dealer.

Trunk Lid Not Properly Shut
The telltale turns on when the trunk lid is not properly closed, along with the icon, an image of the vehicle with an open trunk lid appears on the display. A buzzer is heard when the trunk lid is open and the vehicle is moving. Close the trunk lid properly.

AMBER SYMBOLS

Engine Immobilizer Failure/Break-In Attempt
Engine Immobilizer System Failure The telltale will illuminate to report a failure of the Engine Immobilizer system. Break-In Attempt The telltale will illuminate when the ignition is cycled to ON position, to indicate a possible break-in attempt detected by the alarm system. Electronic Key Not Recognized The telltale will illuminate when the engine is started and the electronic key is not recognized by the system. Alarm System Failure The telltale will illuminate to report an alarm system failure. Contact an authorized dealer as soon as possible.
Fuel Cut-Off Indicator Light
The telltale will illuminate after an accident has occurred and the system has shut the fuel off. For reactivating the fuel cut-off system. If it is not possible to restore the fuel supply, contact an authorized dealer.

Park Sensors System Failure
The telltale will illuminate when the system has failed or is not available. Contact an authorized dealer to have the system checked.
Engine Oil Change Required — If Equipped
The telltale is illuminated only for a limited time.

NOTE: After the first indication, each time the engine is started the symbol will continue to illuminate as described above until the oil is changed. If the telltale flashes, this does not mean that there is a fault on the vehicle, rather it simply reports that it is now necessary to change the oil as a result of regular use of the vehicle. The deterioration of engine oil is accelerated by using the vehicle for short drives, preventing the engine from reaching operating temperature. Contact an authorized dealer as soon as possible.

CAUTION! Deteriorated engine oil should be replaced as soon as possible after the symbol is switched on, and never more than 500 miles (805 km) after it first switches on. Failure to observe the above may result in severe damage to the engine and invalidate the New Vehicle Limited Warranty. When this symbol comes on, it does not mean that the level of engine oil is low, so if it flashes you do not need to top up the engine oil.

Engine Oil Pressure Sensor Failure

The telltale will illuminate in the event of engine oil pressure sensor failure. Contact an authorized dealer as soon as possible.

Engine Oil Level Sensor Failure
The telltale will illuminate in the event of engine oil level sensor failure. Contact an authorized dealer as soon as possible.

Forward Collision Warning (FCW) System Failure — If Equipped
The telltale will illuminate in the case of failure of the Forward Collision Warning system. Contact an authorized dealer as soon as possible.

Stop/Start System Failure
This telltale will illuminate to report a Stop/Start system failure. Contact an authorized dealer as soon as possible to have the failure eliminated.

Rain Sensor Failure
The telltale will illuminate in the case of failure of the automatic windshield wiper. Contact an authorized dealer as soon as possible.

Dusk Sensor Failure
The telltale will illuminate in the case of failure of the automatic low beam alignment. Contact an authorized dealer as soon as possible.
Blind Spot Monitoring System Failure — If Equipped
The telltale will illuminate in the event of a Blind Spot Monitoring system failure. Contact an authorized dealer as soon as possible.
Fuel Level Sensor Failure
The telltale will illuminate in the event of fuel level sensor failure. Contact an authorized dealer as soon as possible.
Exterior Lights Failure
The telltale will illuminate to indicate a failure on the following lights: daytime running lights (DRLs) / parking lights / trailer turn signal indicators (if present) / trailer lights (if present) / side lights / turn signal indicators / rear fog light / reversing light/brake lights/license plate lights. The failure may be caused by a blown bulb, a blown protection fuse, or an interruption of the electrical connection. Replace the bulb or the relevant fuse. Contact an authorized dealer.

Keyless System Failure
The telltale will illuminate in the event of keyless system failure. Contact an authorized dealer as soon as possible.
Fuel Cut-Off System Failure
The telltale will illuminate in the event of fuel cut-off system failure. Contact an authorized dealer as soon as possible.
Lane Departure Warning (LDW) System Failure — If Equipped
The telltale will illuminate in the event of a fault in the Lane Departure Warning system. Contact an authorized dealer as soon as possible.
Automatic High Beam Headlights Failure — If Equipped
The telltale will illuminate to report a failure of the automatic high beam headlights. Contact an authorized dealer as soon as possible to have the failure eliminated.
Automatic Transmission Fluid Overheating
The telltale will illuminate in the case of transmission overheating, after a particularly demanding use. In this case, an engine performance limitation is carried out. Wait for the telltale to turn off with the engine off or idling.

Audio System Failure
The telltale will illuminate to report a failure of the audio system. Contact an authorized dealer as soon as possible to have the failure eliminated.
Speed Limiter System Failure
While driving, the telltale will illuminate to signal a Speed limit system failure. Contact an authorized dealer as soon as possible to have the failure eliminated.
Loose Fuel Filler Cap
Lights up if the fuel tank cap is open or not properly closed. Tighten the cap properly.
Electric Park Brake Failure
The telltale will illuminate and a message will display to signal a failure in the electric park brake system. This failure may partially or completely block the vehicle because the park brake could remain activated even if automatically or manually disengaged using the relevant controls. In these circumstances, you can disengage the parking brake following the emergency disengagement procedure. If you are still able to drive the vehicle (park brake is not engaged), drive to the nearest authorized dealer and remember, when executing any maneuvers/commands, that the electric parkbrake is not operational.

WARNING! If a failure is present with sharp braking, the rear wheels may lock and the vehicle may swerve.

Low Coolant Level — If Equipped
This telltale will illuminate to indicate that the vehicle coolant level is low.
Service Adaptive Cruise Control (ACC) System
This light will illuminate when the ACC is not operating and needs service. Contact an authorized dealer to have the system checked.
Wear On Brake Pads
This light will illuminate when the brake pads have reached their wear limit. Contact an authorized dealer as soon as possible.
NOTE: Always use genuine parts or similar because the Integrated Brake System (IBS) system could detect anomalies.
Dynamic Drive Control System Failure
The telltale will illuminate to signal a failure in the dynamic drive control system.
Windshield Wiper Failure
Signals a windshield wiper failure. Contact an authorized dealer.

Generic Indication
Signals information and failures. The accompanying messages describe the failure.
All Wheel Drive Failure
This telltale will illuminate along with an accompanying message when the AWD dynamic control system is temporarily deactivated to prevent damage. The traction system will work in RWD mode in this instance. Contact an authorized dealer as soon as possible to have the failure eliminated.
Temporary All Wheel Drive Failure — If Equipped
This telltale will illuminate to indicate that the AWD dynamic control system is temporarily deactivated to prevent damage. The traction system will work in RWD mode in this instance. In the event that this telltale illuminates, reduce the load to allow the system to cool down. The AWD system will resume normal operation when the symbol disappears from the display.
ABS Activation
This telltale will illuminate to indicate that the ABS system has been activated.
Adaptive Front Lighting System Failure
The telltale will illuminate to indicate the automatic directional light system failure. Go to an authorized dealer to have the system checked.

Soft Suspension Calibration Insertion — If Equipped
The telltale will illuminate when the most comfortable suspension setting is activated.
Shock Absorbers Failure
While driving, if the telltale illuminates, it signals a failure in the suspension system. Contact an authorized dealer to have the system checked.
Windshield Washer Liquid Level
The telltale will illuminate to indicate that the level of the windshield and headlight washing fluid (if any) is low. Always use liquid with the features indicated in the “Fluids And Lubricants”.
WEAR ON Carbon Ceramic Material (CCM) Brake Discs — If Equipped
This light will illuminate when the carbon-ceramic material brake discs have reached their wear limit. Contact an authorized dealer as soon as possible.

WARNING! It is recommended to use only OEM brake pads to ensure the original performance of the braking system.

Driver Attention Assist (DAA) System Failure
The symbol comes on in the event of a DAA system failure. Contact an Alfa Romeo Dealership as soon as possible to have the failure eliminated.
Highway Assist System (HAS)/Traffic Jam Assist (TJA) System Failure
The symbol lights up in case of HAS or TJA system failure. Contact an Alfa Romeo Dealership as soon as possible to have the failure eliminated.

GREEN SYMBOLS

Headlights
The telltale will illuminate when the headlights are turned on.
Automatic Headlights
The symbol lights up when the automatic headlights are on.
Stop/Start Operation
The telltale will illuminate in the case of Stop/Start system intervention (stopping the engine). When the engine is restarted, the telltale will shut off.

Cruise Control Activated
The telltale will illuminate when the Cruise Control system is activated.
Adaptive Cruise Control System — If Equipped
The symbol comes on when the Adaptive Cruise Control system is activated.

BLUE SYMBOLS

Automatic High Beam Headlights — If Equipped
The telltale will illuminate when the automatic high beam headlights are activated.
High Beam Headlights
The telltale will illuminate when the high beam headlights are activated.

FAQ