2022 Audi A3 Instrument Cluster Setup Guide
Introduction
Welcome to a closer look at the avant-garde and opulent 2022 Audi A3 instrument panel. This manual redefines how you engage with the data and controls in your car by examining the cutting-edge engineering and design that go into its creation. The 2022 Audi A3’s instrument cluster is more than simply a set of gauges; it’s a dynamic, adaptable display that effortlessly combines important driving information with contemporary design.
Join us as we explore the features and capabilities that distinguish the instrument cluster of the 2022 Audi A3 whether you’re a tech fanatic or you just love the finer points of automotive design. Get ready to explore a new realm of personalized driving information and innovation that fits your requirements and tastes.
Instrument Cluster
Instrument cluster overview
Depending on the vehicle equipment, the following items may appear in the instrument cluster:
- (D Left dial
- Tachometer
- Tab area
- Central area Status line (one or two lines)
Right dial- Convenience display
- Display
- Fuel level 5)
- Right additional display with speedometer
- Left additional display with:
- Selector lever position
- Audi drive select mode
- Display
- Engine coolant temperature
WARNING
If there is a serious system malfunction, the display may turn off. The indicator bight may als0 turn on. Stop the vehicle safely. See an authorized Audi dealer or authorized Audi Service Facility for assistance.
Tips
- The following pages primarily show illustrations of the Audi virtual cockpit plus*. The display ,or location of the items that are shown may vary on the different versions of the instrument cluster.
- You can select the units used for temperature, speed, and other measurements Speeds are displayed in mph (miles per hour) or km/h (kilometers per hour).
- Certain instrument cluster content can also be displayed in the head-up display*
Operating
Information is organized within various tabs G) in the instrument cluster. The tab contents are displayed in the central area@.
Requirement: the ignition must be switched on.
Selecting a tab
- Press the
button® repeatedly until the desired tab is selected.
Returning to functions at higher levels
Press the 
button ®·
Opening and closing the menu
- Press the button .
Selecting and confirming a function
Requirement: a menu or list must be displayed.
- To select a function, turn the left thumbwheel (J) to the desired function.
- To confirm a selection, press the left thumb- wheel (z).
Switching the view
- Press the VIEW button
Information is organized within various tabs G) in the instrument cluster. The tab contents are displayed in the central area@.
Requirement: the ignition must be switched on.
Selecting a tab
Press the button® repeatedly until the desired tab is selected.
Returning to functions at higher levels
- Press the button ®·
Opening and closing the menu
- Press the button @.
Selecting and confirming a function
Requirement: a menu or list must be displayed.
- To select a function, turn the left thumbwheel (J) to the desired function.
To confirm a selection, press the left thumb- wheel (z).
Switching the view
- Press the VIEW button
The following tabs may be available, depending on vehicle equipment:
Adjusting the display
Switching the view
Applies to: Audi virtual cockpit
Press the VIEW button to switch between the default view G) and the enhanced view@.
Adjusting the layout
Applies to: Audi virtual cockpit
Depending on the vehicle equipment, various layouts may be available.
- Applies to: MMI: Select on the home screen: SETTINGS> Display & brightness> Audi virtual cockpit.
To adjust the desired layout, press@.
Adjusting the additional display
Applies to: Audi virtual cockpit
Depending on the vehicle equipment, the additional displays that can be selected may vary.
- Applies to: MMI: Select on the home screen: SETTINGS> Display.& brightness > Audi virtual cockpit> Configure.
Select the desired additional display.
Reducing the display
Depending on the vehicle equipment, you can hide the central area in the instrument cluster.
- Select on the instrument cluster: vehicle functions tab button Reduced display, or
Press the VIEW button on the multifunction steering wheel.
Coolant temperature display
Applies to: vehicles “With a coolant temperature indicator
The coolant temperature display® only functions when the ignition is switched on. To reduce the risk of engine damage, please observe the following notes about the temperature ranges.
Cold range
If only the LEDs at the bottom of the gauge turn on, the engine has not reached operating temperature yet. Avoid high engine speeds, full acceleration, and heavy engine loads.
Normal range
The engine has reached its operating temperature once the LEDs up to the center of the gauge turn on. If the indicator light in the instrument cluster display turns on, the coolant temperature is too high .
Note
- Auxiliary bead lights and other accessories in front of the air intake impair the cooling effect of the tool ant. This increases the risk of the engine overheating during high outside temperatures and heavy engine load.
The front spoiler also helps to distribute cooling air correctly while driving. If the spoiler is damaged,, the cooling effect will be impaired and the risk of the engine overheating will increase. See an authorized Audi dealer or authorized Audi Service Facility for assistance.
Tachometer
indicator light turns on, the engine will be automatically limited to the RPM displayed in the instrument cluster. This will protect the engine components, for example during a cold start or from overheating.
indicator light also turns on. Make sure the engine speed does not go above the speed displayed, for example when downshifting. Drive to an authorized Audi dealer or authorized Audi Service Facility immediately to have the malfunction corrected.The needle in the tachometer may only be in the red area of the gauge for a short period of time before there is a risk of damaging the engine. The location where the red zone begins varies depending on the engine.
The trip odometer and odometer are displayed in the status bar©
The trip odometer shows the distance driven since it was last reset. It can be used to measure short distances. The odometer shows the total distance that the vehicle has been driven.
- Select on the instrument cluster: vehicle functions tab CT§ button Reset mi.
- Tips
Distances are displayed in mi (miles) or km (kilometers).
FAQs
Start your Audi A3 and move to the “Menu” button on the multifunction steering wheel to access the instrument cluster setting menu. In the list of choices, navigate to “Instrument Cluster” and click it.
The data shown on the instrument cluster can be changed, yes. You can choose “Individual” to tailor the information you view by navigating the menu using the arrow buttons on the steering wheel.
You can tailor media playing information, journey data, vehicle status, and navigation directions to your tastes.
Navigate to the “Theme” selection in the configuration menu for the instrument cluster. You can select from a number of themes that alter the cluster’s color scheme and design.
Yes, you can change the instrument cluster brightness by selecting the “Brightness” option in the settings menu and using the arrow buttons to increase or reduce it.
You can, in fact, alter the instrument cluster’s language. Choose your favorite language by going to the “Language” menu item in the settings menu.
Locate the “Driver Assistance” area in the setup menu. You can then decide which driver assistance alerts you want to enable or disable.
Yes, by choosing the “Reset” option in the trip computer part of the instrument cluster menu, you can reset trip data such as average fuel consumption and travel time.
Yes, you can use Bluetooth or other connectivity methods to connect your smartphone. This might make functionality like showing media content or notifications on the instrument cluster possible.
You may switch between the traditional view, the digital view, and the navigation-focused view by pressing the “View” button on the steering wheel.
To avoid driving weariness, the “Rest Recommendation” feature suggests pauses based on how long you’ve been driving. In the settings menu for the instrument cluster, it can be enabled or disabled.
You might be able to upgrade your Audi A3 via over-the-air (OTA) updates or by going to an authorized service location, depending on the technology package.
To get out of the setup menu, just push the “Menu” button on the steering wheel until you see the main display again.
In order to reduce distractions while driving, it is best to perform instrument cluster configuration changes while the car is still moving.
If you run into any problems, see the owner’s manual for your Audi A3 or get in touch with your local Audi service center for help and troubleshooting.
Useful links
View Full PDF: 2022 Audi A3 Owner’s Manual| Auto User Guide