AstroAI S8 Car Jump Starter Adventures User Manual
If your car battery dies, the AstroAI S8 Car Jump Starter is a reliable, small device that can help you get back on the road. This jump starter is unique because it has a high peak current and a large battery capacity. This means that it can start a lot of different vehicles, from small cars to big trucks, more than once on a single charge. It usually has safety features like a built-in flashlight, USB ports for charging other devices, and protection against overcurrent, short circuits, and overcharging. This makes it a useful tool for both everyday use and emergencies.
How to Operate AstroAI S8
Operating the AstroAI S8 Car Jump Starter involves a few straightforward steps. Here’s a general guide on how to use it:
- Charge the Jump Starter: Before using it, ensure that the AstroAI S8 is fully charged. You can charge it using the provided USB cable or a compatible charger.
- Prepare Your Vehicle: Make sure that all your vehicle’s electrical systems are turned off (radio, lights, air conditioning, etc.).
- Connect the Clamps: The jump starter comes with red and black clamps. Connect the red clamp to the positive (+) terminal of your car battery and the black clamp to the negative (-) terminal. Ensure the connections are secure.
- Turn On the Jump Starter: After the clamps are properly connected, turn on the jump starter. Some models may have an indicator light or sound to confirm a good connection.
- Start Your Vehicle: Try to start your vehicle. If it doesn’t start right away, wait a few minutes and try again. Avoid cranking the engine for more than 3-5 seconds at a time to prevent damage to the jump starter or car battery.
- Disconnect the Jump Starter: Once your vehicle starts, turn off the jump starter before disconnecting the clamps. Remove the black clamp (negative) first, followed by the red clamp (positive).
- Recharge the Jump Starter: After use, it’s a good practice to recharge your jump starter so it’s ready for the next use.
WARNING
- This jump starter is not a toy. Incorrect usage may cause injuries and accidents.
- This jump starter cannot be used as a car battery.
- Do not press the Boost Button before connecting to the car battery.
- Do not connect the red clamp to the black clamp.
- Keep out of the reach of children.
- Do not use the car jump starter to start your car while the jump starter is charging.
- Please do not soak the jump starter in water or expose it to rain.
- Do not modify or disassemble the jump starter. Jump starter repair work should only be performed by professional technicians.
- Do not operate the jump starter in a dangerous environment or around flammable liquid, gas, or dust.
- Only use this product with the included smart battery clamps. Do not use the jumper clamps if they are damaged or if the cables are damaged.
- Compatible with 12 V vehicles only. Inappropriate usage may cause accidents or injuries. (Please do not use this product on non-12 V vehicles, such as airplanes and other 24 V vehicles/boats.)
- Ensure the battery terminals are clean and the jumper clamps are undamaged before starting your car. A dirty connection may reduce performance.
- Ensure the blue plug on the smart battery clamps is fully inserted into the socket, or it may burn.
- Ensure the jump starter’s battery level exceeds 75% before starting your car.
- Take off any metal accessories, such as rings, bracelets, or necklaces, before you operate the jump starter.
- Do not continuously jumpstart your car; doing so may cause the jumpstart to overheat and sustain damage. (Allow a 30-second interval between jump starts to avoid overheating the jump starter.)
- Remove the jump starter from the vehicle’s battery within 30 seconds of jumpstarting your car. Failure to do so may cause damage.
- Do not drop/toss the jump starter. If the jump starter is hit or damaged, a qualified battery technician will need to test it.
- Do not store the jump starter at temperatures above 70 ‘C/158 ‘F.
- You may dispose of the lithium battery according to local guidelines when its service life has ended.
PACKAGE INCLUDES
- Multifunctional Jump Starter X 1
- Smart Battery Clamps X 1
- USB-A to USB-C Charging Cable X 1
- USB Wall Charger X 1
- Storage Bag X 1
- User Manual X 1
AstroAI S8 DIAGRAM
- Power Button
- Battery Level Indicator
- 12 V Jumpstart Port
- Quick-Charge Input Port
- Smart Battery Clamps
- 5 V= 2.4 A Output Port
- LED Flashlight (Emergency Light)
- Storage Bag
- USB-A to USB-C Charging Cable
- USB Wall Charger
PREPARATION
Fully charge the jump starter after receiving it.
Checking the battery level
Press the Power Button to check the battery level, then the battery indicators will illuminate up:
Charging the device
Note: The battery indicators will illuminate circularly while charging; the illuminated indicators represent the current battery level. If all four of the battery indicators are off, it means the charging is complete.
- Connect the USB-A part of the USB charging cable to the power
source’s output port. - Connect the USB-C part of the USB charging cable to the jump starter’s USB-C input port.
INSTRUCTIONS
Jumpstarting Function
- Fully insert the smart battery clamps into the jump starter. Connect the red clamp to the battery’s positive terminal(+) and the black clamp to the battery’s negative terminal(-).
- Operate the jump starter according to the indicator on the smart battery clamps.
- Illuminated green indicator: Correct connection, it is safe to operate. Move to step 3.
- Illuminated red indicator with buzz sounds: Reversed connection, please reconnect the positive and negative terminals correctly. Continue to step 3 after the indicator turns green.
- The indicator flashes green: Low battery voltage. Please press the Boost Button and wait until the indicator turns green. Then, complete step 3 within 30s.
- When the smart battery clamps’ indicator is illuminated green, jumpstart your car.
- After successfully jump-starting the car, disconnect the smart battery clamps.
Tip
- Turn off any electrical devices in the vehicle before jump-starting it.
- If the vehicle does not start within 5 seconds of attempting ignition, stop and remove the clamps. Wait for 60 seconds and retry step 3.
- If the indicator on the smart battery clamps does not light up at all: The battery may be damaged. You may retry step 2.3 when the battery clamps are correctly attached, or contact AstroAI.
Power Bank Function
- Insert the USB plug into the 5 V=2.4 A output port.
- Connect the other end of the USB Charging cable to the device being charged.
- Press the Power Button to charge the devices. The jump starter will automatically detect the devices· specifications and charge them at the proper voltage.
Illumination Function
Press and hold the Power Button for 3 seconds to turn on the illumination function. Press the button again to choose between Flashlight mode, Strobe mode, SOS mode, and OFF.
MAINTENANCE
- To maximize the battery’s performance and service life, please charge the jump starter when its battery level is lower than 75%.
- Please fully charge the jump starter if it is about to be idle for a long time. And charge it every three months to extend its service life.
SPECIFICATIONS
- Model: S8
- Capacity: 37 Wh
- Jumpstart Current: 500 A (1 5) 300 A (3 5)
- Peak Current: 1500 A
- U5B Output: U5B1 +U5B2 5V=2.4 A
- U5B Input: Quick Charge (5 V = 3 A)
- Operation Temperature: -4 ° F~122 ° F; -20 ° C~50 ° C
- Charge Temperature: 14 ° F~113 ° F;-10 ° C~45 ° C
- Time to Fully Charge: Approximately 3 Hours
- This jump starter features four built-in 3.7 V lithium batteries in a
series connection. - The battery pack capacity is 2500 mAh (14.8V), equivalent to 1 DODO 6mAh (3.7V).
RECYCLING
You may dispose of the jump starter when its service life has ended, please recycle the recyclable parts according to local guidelines.
WARRANTY PERIOD
2-Year Limited Warranty from AstroAI
Each AstroAI Multifunctional Jump Starter will be free from defects in material and craft. This warranty does not cover damage from neglect, misuse, contamination, alteration, accident, or abnormal conditions of operation or handling. This warranty covers the original purchaser only and is not transferable.
FAQS for AstroAI S8
The AstroAI S8 typically has an indicator light or display showing the charge level. It’s fully charged when the indicator shows 100% or the light turns green.
The AstroAI S8 is designed to jump-start most 12V vehicles, including cars, trucks, motorcycles, and boats, but check the specifications for the maximum engine size it can handle.
Connect the red clamp to the positive (+) terminal and the black clamp to the negative (-) terminal of the battery. Ensure connections are secure.
Crank the engine for no more than 3-5 seconds at a time. If the car doesn’t start, wait a couple of minutes before trying again.
If the car doesn’t start after several tries, stop and seek professional help. The issue might not be battery-related.
Yes, it usually comes with USB ports for charging small electronic devices like smartphones and tablets.
Regularly charge it, at least every 3-6 months, keep it in a cool, dry place, and avoid exposing it to extreme temperatures.
No, the AstroAI S8 is designed with safety features to prevent overcharging and damaging the battery.
It’s best to use the jump starter in dry conditions. While it may have some water-resistant features, it’s not waterproof.
It often includes overcurrent protection, short circuit protection, overload protection, and over-voltage protection.
The jump starter usually indicates a secure connection with a light or a beep. Ensure the clamps are firmly attached to the battery terminals.
No, disconnect the jump starter immediately after the car starts to avoid any potential electrical issues.
It depends on the condition of the battery being jumped, but generally, it can perform multiple jumps on a single charge.
Store it in a cool, dry place, away from direct sunlight and extreme temperatures, preferably in its carrying case.