BUTURE Beta04 Car Battery Jump Starter Start Owners Manual
The BUTURE Beta04 Car Battery Jump Starter is a very useful and effective tool for drivers who need to jump-start their car’s battery in an emergency. It is easy to jump-start 12V vehicles like cars, trucks, motorcycles, and boats with this small but powerful device. With a peak current of up to 2000 amps, it can easily charge and power up a dead battery in seconds, even if the weather is bad. The Beta04 is more than just a jump starter; it’s also a portable power bank with USB ports that can charge phones, tablets, and other USB-powered gadgets. With advanced safety features like over-current protection, short-circuit protection, and reverse polarity protection, it makes sure that the experience is safe and easy to use. It’s built to last and has an LED flashlight with multiple modes built in. This makes it an essential tool for everyday use, roadside emergencies, and outdoor adventures.
How to Operate BUTURE Beta04
Operating the BUTURE Beta04 Car Battery Jump Starter is relatively straightforward. Here’s a step-by-step guide to help you use it effectively:
- Preparation
- Ensure that the jump starter is fully charged before use.
- Make sure your vehicle’s engine is turned off.
- Connecting the Jumper Cables
- Open the protective cover on the jump starter to reveal the jumper cable port.
- Connect the jumper cables to the jump starter. The cables are typically color-coded – red for positive (+) and black for negative (-).
- Attaching to the Car Battery
- Connect the red clamp to the positive (+) terminal of your car battery.
- Connect the black clamp to a grounded metal part of the car – this could be a bolt or a bracket, away from the battery and fuel system.
- Safety Check
- Ensure that the connections are secure.
- Stand back from the battery to avoid any sparks or hazardous fumes.
- Initiating the Jump Start
- Turn on the BUTURE Beta04 jump starter.
- If your model has a safety switch or button, ensure it’s in the correct position to initiate the jump start.
- Starting the Vehicle
- Go to your vehicle and start the engine. It should crank and start running.
- If the car doesn’t start immediately, wait a few minutes and try again. Avoid continuous cranking as it could harm the starter.
- Disconnecting the Jumper Cables
- Once the car engine starts, turn off the jump starter.
- Carefully disconnect the black clamp first from the car, followed by the red clamp.
- Disconnect the jumper cables from the jump starter.
- Post-Jump Procedures
- Let your vehicle’s engine run for a while to recharge the battery.
- Store the jump starter in a cool, dry place and recharge it if necessary.
- Regular Maintenance
- Regularly check and recharge the jump starter to ensure it’s ready for use.
Remember, safety is paramount when dealing with car batteries and electrical systems. If you’re unsure or uncomfortable with the process, it’s advisable to seek assistance from someone with experience or a professional. Always refer to the BUTURE Beta04’s user manual for specific instructions and safety information related to your particular model.
Product Overview
- Jumpstart Port
- Force Start Button
- Display
- USB Output 1 (18W)
- USB C Input/Output (PD 65W Max)
- DC Output
- USB Output 2 (18W)
- Power Button
- LED Light
- Power Level
- Quick Charging
- Ready to Work
- Force Start Mode
- Error Indicator
- Charging
- Discharging
Jump Start Your Car
- Insert the jumper cable into the jump starter and connect the
clamps to car battery (red to +, black to -). - The sign shows on the screen.
- Start your car engine.
ABOUT THE FORCE START FUNCTION
If the screen doesn’t display anything when you correctly connect the clamps to your car, you can use the Force Start Function to enter boost
mode.
3 steps to fix the problem:
- Press the force start button for 5 seconds.
- The 2 signs show on the screen.
- Start your car engine.
Warning: When using the Force Start Function, auto-detection and safety features will be disabled.
About the TroubleShoot
Recharge
- Insert the charging cable into the USB C port.
- Connect to the corresponding adaptor (adaptor not included).
CHARGE ELECTRONIC DEVIDES
- Plug the cable into the corresponding outport.
- Connect to electronic products like smartphones.
- Press the power button.
CHARGE 12V DC DIVIDES
- Plug the cigarette lighter into the DC outlet.
- Connect to 12V DC devices like tire pumps.
- Press the power button.
LED Lightning
PRECAUTIONS
- The product is for 12V vehicles only.
- Do not use the product with less than 10% power as this will damage the product.
- Recharge every 3 months to prolong the lifespan.
- Wait at least 30 minutes before recharging after starting the car.
- The 60s is recommended between starts, otherwise, it will overheat.
IMPORTANT SAFETY WARNING
- Store in a cool and well-ventilated place out of reach of children and pets.
- Do not place the product in a high-temperature environment for a long time. The operation temperature of this product is -20-60 C. The storage temperature should not exceed 50 C /122 F.
- Only start vehicles with the smart jumper cable supplied by the
manufacturer. - Do not use the product if the clamp or cable is damaged.
- Do not connect the red and black clamps when the product is outputting.
- Do not connect the red and black clamps to the same piece of metal.
- Do not disassemble or modify this product.
- Do not use detergent to clean this product.
- Do not abuse this product and avoid heavy dropping or repeatedly
hitting it. - Do not operate the product in explosive environments such as
flammable liquids, gases, or dust. - Do not immerse the product in water.
- Do not litter the product and it should be safely recycled.
- Do not incinerate the product or be exposed to high temperatures, as they may explode.
- Only use replacement parts or accessories provided or recommended by the manufacturer.
FAQs Of BUTURE Beta04
A: It is designed to jump-start 12V vehicles, including cars, trucks, motorcycles, boats, and RVs, especially suitable for gas engines up to 8.0L and diesel engines up to 6.5L.
A: It can perform up to 30 jump starts on a single charge, though this may vary depending on the battery condition and type.
A: The Beta04 offers a peak current of 2000 amps, making it powerful enough to jump-start most vehicles.
A: Yes, it includes over-current protection, short-circuit protection, overload protection, over-voltage protection, and over-charge protection for safe operation.
A: It typically takes about 4-6 hours to fully charge.
A: Yes, it features USB ports for charging devices like smartphones, tablets, and other USB-powered gadgets.
A: It has LED indicators that display the battery level and charging status.
A: While it’s sturdy, it’s not fully waterproof, so it’s best to use it in dry conditions and store it properly.
A: Yes, it comes with a built-in LED flashlight with multiple modes, including SOS and emergency strobe.
A: Store it in a cool, dry place and recharge it every three to six months to maintain battery health.
A: Yes, it’s designed to function effectively in various weather conditions, including cold weather.
A: It’s compact and portable, but the exact weight and dimensions should be checked in the product specifications.
A: Yes, it comes with its own set of jumper cables.
A: It can be used to power 12V appliances, as long as they fall within its output capacity.
A: The warranty period varies, so it’s best to consult the manufacturer or retailer for accurate information.
