BUTURE BR800 Car Battery Jump Starter User Manual

BUTURE BR800 Car Battery Jump Starter User Manual

For drivers, the BUTURE BR800 Car Battery Jump Starter is a very useful and durable emergency tool. It has a strong battery with a peak current of 800 amps, so it can jump-start most 12V vehicles, like cars, trucks, motorcycles, and boats, more than once on a single charge. The small size hides extra useful features like an LED flashlight with different modes, a built-in compass, and two USB ports that let you charge your devices while you’re on the go. This unit puts safety first by having over-current protection, short-circuit protection, overload protection, over-voltage protection, and overcharge protection. This makes it a reliable and safe choice for unexpected car emergencies and many outdoor activities.

How to Operate BUTURE BR800

Operating the BUTURE BR800 Car Battery Jump Starter is a simple process, but it is crucial to follow the correct steps to ensure safety and effectiveness. Here is a step-by-step guide:

1. Charge the Device: Before using the jump starter, make sure it is fully charged. Use the provided charging cable to charge it from a wall outlet or a USB port until the indicator light shows that the battery is full.
2. Prepare for Use: Ensure all electronics in the vehicle are turned off, and the vehicle’s ignition is in the OFF position.
3. Connecting the Clamps:
   • Open the vehicle’s hood and locate the battery.
   • Connect the red clamp to the positive (+) battery terminal.
   • Connect the black clamp to the negative (-) battery terminal or a metal ground on the vehicle’s frame.
4. Turn on the Jump Starter: Power on the BUTURE BR800. Some models might have a button or switch to initiate the jump-start mode.
5. Start the Vehicle
   • Try to start the vehicle. If it doesn’t start right away, wait for a few minutes and try again.
   • Don’t crank the engine for more than 3 seconds. If the car doesn’t start, wait at least 30 seconds before trying again to allow the jump starter to cool down.
6. Disconnecting
   • Once the vehicle has started, turn off the jump starter.
   • Disconnect the black clamp first, followed by the red clamp.
   • Safely secure the battery clamps to the jump starter to prevent accidental shorting.
7. After Use:
   • Recharge the jump starter as soon as possible to ensure it’s ready for the next use.
   • Store the BUTURE BR800 in a cool, dry place.
8. Regular Maintenance:
   • • Even if not in use, recharge the jump starter every 3-6 months to preserve battery life.

Always refer to the user manual provided with your BUTURE BR800 for any specific instructions related to your model. Proper care and regular maintenance will ensure the longevity and reliability of your jump starter.

Package Content

Know Your Product

1. ON/OFF Button
2. Battery Indicator
3. 5V/2.4A Output
4. Flashlight
5. Input
6. Jump Starting Port

Powerful Circuit Protection System – Smart Clamps

1. Red Jumper Cable (+)
2. Black Jumper Cable (-)
3. Smart Clamp Plug

Technical Details

Operation

Power indicator light
Press the power button to check the capacity of the Jump starter. Indicator Lights as below picture (25%,50%,75%, 100%)

Recharge the Jump starter
Note: The wall charger or car charger is not included in the package, you can use a universal USB charger to recharge the unit, such as your phone or pad charger ( 5V/2A is suggested).

At Home

1. Plug the charging cable into any USB wall adaptor (not included).
2. Connect the charging cable (included) to the unit.

In Car

1. Plug the USB car adapter (not included) into an available 12V socket.
2. Connect the charging cable (included) to the unit.

Note
It is recommended to recharge the Jump starter every 3-4 months to maintain the efficiency and prolong the service life of the internal battery even if the unit has not been used.

Charging your devices from the output
Use the original manufacturer’s charging cable that came with your device and plug it into one of the output ports. You can charge your phone or tablet via the output at 5V/2.4A. Press the power button once to begin charging your device. The power level indicator will show the battery level. To check the power capacity again simply press the power button once.

To Jump Start Your Car
To jump-start the vehicle battery, put the vehicle in park (neutral if the vehicle has a manual transmission) and engage the emergency brake. Locate the battery for the vehicle and follow the steps listed below. Jump cables are color-coded, RED for POSITIVE(+) and BLACK for NEGATIVE(-) Do not mix up the cables or allow the metal ends to touch together because this may damage the battery charging system and/or electronics on a vehicle.

NOTE: This product is for 12V cars only. Check to make sure that 3 or 4 indicator lights are illuminated (battery level is above 50%) before you use it to start your car.

1. Insert the plug of the smart battery clamp completely into the jump starter. If the green and red light indicators on the battery clamp are flashing alternately, you are safe to move on to the next step.
2. Connect the red clamp to the positive terminal(+) of the car battery and connect the black clamp to the negative-) of the car battery. If the indicator light of the smart clamp is solid green, you can move on to the next step. However, if the red indicator light is on:
   • The battery clamp may be connected in reverse. In this case, you need to
     disconnect the battery clamp from the vehicle and the jump starter.
   • Adjust the clamps for maximum contact with the battery terminals.
3. Start Your Car
   If you fail to start your car, you need to disconnect the battery clamp from the vehicle and the jump starter. Wait for at least 30 seconds, then try again.
4. Once your car is started, remove the battery clamp from the car battery and the jump starter within 30 seconds.

In any of the following situations, the smart clamp turns protection on:

Warnings

1. When jump-starting a vehicle, please ensure that the blue plug is securely fitted into the jump start socket on your jump starter.
2. Do not allow this product in water.
3. Do not operate the product in explosive atmospheres, such as in the presence of flammable liquid, gas, or dust.
4. Do not modify or disassemble the product.
5. If battery leakage occurs, take it to your local battery recycling center for disposal do not attempt to use it.
6. This car jump starter is for use with 12V vehicles only.

Battery Disposal
The battery is self-contained and not consumer-replaceable. The battery must be disposed of properly when it no longer holds a charge. Proper charging practices will increase the life of the product.

Warranty
Our company provides customers with a warranty of 24 months from the date of purchase.

Contact US
For additional assistance or warranty cover claim, please contact us:
E-Mail: support@ibuture.com

 

FAQs Of BUTURE BR800