Chevrolet Blazer 2023 Universal Remote System User Guide
Universal Remote System
Messages displayed on the Driver Information Center (DIC) indicate the status of the vehicle or some action that may be needed to correct a condition. Multiple messages may appear one after another. The messages that do not require immediate action can be acknowledged and cleared by pressing the thumbwheel. The messages that require immediate action cannot be cleared until that action is performed. All messages should be taken seriously; clearing the message does not correct the problem. If a SERVICE message appears, see your dealer. Follow the instructions given in the messages. The system displays messages regarding the following topics.
- Service Messages
- Fluid Levels
- Vehicle Security
- Brakes
- Steering
- Ride Control Systems
- Driver Assistance Systems
- Cruise Control
- Lighting and Bulb Replacement . Wiper/Washer Systems
- Doors and Windows
- Seat Belts
- Airbag Systems
- Engine and Transmission
- Tire Pressure
- Battery
Engine Power Messages
ENGINE POWER IS REDUCED
This message displays when the vehicle’s propulsion power is reduced. A reduction in propulsion power can affect the vehicle’s ability to accelerate. If this message is on, but there is no observed reduction in performance, proceed to your destination. Under certain conditions, the performance may be reduced the next time the vehicle is driven. The vehicle may be driven while this message is on, but maximum acceleration and speed may be reduced. Anytime this message stays on, or displays repeatedly, the vehicle should be taken to your dealer for service as soon as possible. Under certain operating conditions, propulsion will be disabled. Try restarting after the ignition has been off for 30 seconds.
Vehicle Speed Messages
SPEED LIMITED TO XXX KM/H (MPH)
This message shows that the vehicle speed has been limited to the speed displayed. The limited speed is protection for various propulsion and vehicle systems, such as lubrication, thermal, brakes, suspension, Teen Driver if equipped, or tires.
Universal Remote System
See Radio Frequency Statement 0 337.
Universal Remote System
Programming
If equipped, these buttons are in the overhead console.
This system can replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. These instructions refer to a garage door opener, but can be used for other devices. Do not use the Universal Remote system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982.
Read these instructions completely before programming the Universal Remote system. It may help to have another person assist with the programming process.
Keep the original hand-held transmitter for use in other vehicles as well as for future programming. Erase the programming when vehicle ownership is terminated. See “Erasing Universal Remote System Buttons” later in this section. To program a garage door opener, park outside directly in line with and facing the garage door opener receiver. Clear all people and objects near the garage door. Make sure the hand-held transmitter has a new battery for quicker and more accurate transmission of the radio-frequency signal.
Programming the Universal Remote System
For questions or programming help, see www.homelink.com/gm or call 1-800-355-3515. For calls placed outside the U.S., Canada, or Puerto Rico, international rates will apply and may differ based on landline or mobile phone.
Programming involves time-sensitive actions and may time out causing the procedure to be repeated.
- Hold the end of the hand-held transmitter about 3 to 8 cm (1 to 3 in) away from the Universal Remote system buttons with the indicator light in view. The hand-held transmitter was supplied by the manufacturer of the garage door opener receiver.
- Press and release one of the three Universal Remote system buttons to be programmed. Press and hold the hand-held transmitter button. Do not release the hand-held transmitter button until the indicator light changes from a slow to a rapid flash or continuous light. Then release the hand-held transmitter button.
Some garage door openers may require the substitution of Step 2 with the procedure under “Radio Signals for Some Gate Operators” later in this section. - Press and hold the newly programmed Universal Remote system button for five seconds while watching the indicator light and garage door activation.
- If the indicator light stays on continuously or the garage door moves when the button is pressed, then programming is complete. There is no need to complete Steps 4–6.
- If the indicator light does not come on or the garage door does not move, a second button press may be required. For a second time, press and hold the newly programmed button for five seconds. If the indicator light is continuously lit, or the garage door moves, programming is complete.
- If the indicator light flashes rapidly and the garage door does not move, continue with programming
Steps 4–6.
Learn or Smart Button
- After completing Steps 1–3, locate the Learn or Smart button inside the garage on the garage door opener receiver. The name and color of the button may vary by manufacturer.
- Press and release the Learn or Smart button. Step 6 must be completed within 30 seconds of pressing this button.
- Return to the vehicle and firmly press and hold the trained Universal Remote system button for two seconds and release. Repeat the “press/hold/release” sequence up to three times to complete the training process.
The Universal Remote system should now activate the garage door. Repeat the process for programming the two remaining buttons.
Radio Signals for Some Gate Operators
For questions or programming help, see www.homelink.com/gm or call 1-800-355-3515. For calls placed outside the U.S., Canada, or Puerto Rico, international rates will apply and may differ based on landline or mobile phone. Some radio-frequency laws and gate operators require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for the Universal Remote system to pick up the signal during programming.
If the programming did not work, replace Step 2 under “Programming the Universal.
Remote System” with the following:
Press and hold the Universal Remote system button while pressing and releasing the hand-held transmitter button every two seconds until the signal has been successfully accepted by the Universal. Remote system. The Universal Remote system indicator light will flash slowly at first and then change to a rapid flash or continuous solid light. Proceed with Step 3 under “Programming the Universal Remote System” to complete.
Universal Remote System Operation
Using the Universal Remote System
Press and hold the appropriate Universal Remote system button for at least one-half second. The indicator light will come on while the signal is being transmitted.
Erasing Universal Remote System Buttons
Erase all programmed buttons when vehicle ownership is terminated.
To erase:
- Press and hold the two outside buttons until the indicator light begins to flash.
This should take about 10 seconds. - Release both buttons.
Reprogramming a Single Universal
Remote System Button
To reprogram any of the system buttons:
- Press and hold any one of the buttons.
Do not release the button. - The indicator light will begin to flash after 20 seconds. Without releasing the button, proceed with Step 1 under
“Programming the Universal Remote System.”
Q &A
A1: The Universal Remote System in the Chevrolet Blazer 2023 is a feature that allows you to program and control various compatible devices, such as garage doors, home security systems, and lighting, using buttons integrated into the vehicle.
A2: The Universal Remote System works by using a radio frequency signal to communicate with compatible devices. You can program the system to recognize and control specific devices, enabling you to operate them conveniently from within your vehicle.
A3: Yes, you can program multiple devices with the universal remote system in the Chevrolet Blazer 2023.
A4: To program a device, you typically need to follow the instructions provided in the vehicle’s owner’s manual. The process usually involves pressing specific buttons on the remote system and the device you want to program.
A5: The universal remote system in the Chevrolet Blazer 2023 is compatible with a wide range of devices. However, there may be some limitations depending on the specific device and its compatibility with the system.
A6: No, the universal remote system is designed to be used within the range of the vehicle and cannot be controlled from outside.
A7: In most cases, the universal remote system in the Chevrolet Blazer 2023 does not require any additional accessories. However, for certain devices, you may need to purchase and install specific adapters or modules.
A8: The universal remote system can typically be programmed by the vehicle owner. The process is often straightforward and explained in the owner’s manual. However, if you encounter any difficulties, it is advisable to seek assistance from a professional.
A9: Yes, you can erase programmed devices from the universal remote system. The process for erasing devices is usually described in the vehicle’s owner’s manual.
A10: The number of devices that can be programmed into the universal remote system may vary. The specific limit, if any, will be mentioned in the vehicle’s owner’s manual.
A11: The universal remote system in the Chevrolet Blazer 2023 may have security features to prevent unauthorized access to your programmed devices. Consult the owner’s manual for specific information on the security features.
A12: For safety reasons, it is recommended not to use the universal remote system while driving. It is best to operate the system when the vehicle is stationary.
A13: Yes, the universal remote system in the Chevrolet Blazer 2023 can usually be programmed to work with devices from different brands, as long as they are compatible.
A14: The range of the universal remote system may vary, but it is typically within a certain distance from the vehicle, allowing you to control devices in close proximity to your car, such as in your garage or home.
A15: The specific features and functionalities of the universal remote system may vary depending on the vehicle’s trim level and optional packages. It is recommended to refer to the vehicle’s specifications or consult the owner’s manual for detailed information on additional features.
Useful Links
View Full User Guide: Chevrolet Blazer 2023 User Guide
Download Manuals: https://www.chevrolet.com/support/vehicle/manuals-guides