Chevrolet Bolt EUV 2023 Cruise Control User Guide
Cruise Control
The cruise control lets the vehicle maintain a speed of about 40 km/h (25 mph) or more without keeping your foot on the accelerator. Cruise control does not work at speeds below 40 km/h (25 mph).
Warning
Cruise control can be dangerous where you cannot drive safely at a steady speed. Do not use cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads. With the Traction Control System (TCS) or StabiliTrak/Electronic Stability Control (ESC), the system may begin to limit wheel spin while you are using cruise control. If this happens, the cruise control will automatically disengage. See Traction Control/Electronic Stability Control 0 184. If a collision alert occurs when cruise control is activated, cruise control is disengaged. See Forward Collision Alert (FCA) System 0 215. When road conditions allow you to safely use it again, cruise control can be turned back on. If the brakes or the Regen on Demand paddle are applied, cruise control disengages. Cruise control will disengage if either TCS or StabiliTrak/ESC is turned off.
Press to turn the cruise control system on and off. A white indicator comes on in the instrument cluster when cruise is turned on. Press to disengage cruise control without erasing the set speed from memory.
+RES: If there is a set speed in memory, press briefly to resume that speed or press and hold to accelerate. If cruise control is already active, use to increase vehicle speed.
−SET: Press briefly to set the speed and activate cruise control. If cruise control is already active, use to decrease vehicle speed.
Setting Cruise Control
It is on when not in use, −SET or +RES could get bumped and go into cruise when not desired. Keep off when the cruise is not being used.If is on when not in use, −SET or +RES could get bumped and go into cruise when not desired. Keepoff when the cruise is not being used.
To set a speed:
- Press 5 to turn the cruise system on.
- Get up to the desired speed.
- Press and release −SET. The desired set speed briefly appears in the instrument cluster.
- Remove foot from the accelerator pedal.
The cruise control indicator on the instrument cluster turns green after the cruise control has been set to the desired speed. See Instrument Cluster 0 83.
Resuming a Set Speed
If the cruise control is set at a desired speed and then the brakes are applied or * is pressed, the cruise control is disengaged without erasing the set speed from memory. Once the vehicle speed reaches about 40 km/h (25 mph) or more, briefly press +RES. The vehicle returns to the previous set speed. Increasing Speed While Using Cruise Control If the cruise control system is already activated:
- Press and hold +RES until the vehicle accelerates to the desired speed, then release it.
- To increase the speed in small increments, briefly press +RES. For each press, the vehicle goes about 1 km/h (1 mph) faster.
- The speedometer reading can be displayed in either English or metric units. See Instrument Cluster 0 83. The increment value used depends on the units displayed.
Reducing Speed While Using Cruise Control
If the cruise control system is already activated:
- Press and hold −SET until the desired lower speed is reached, then release it.
- To slow down in small increments, briefly press −SET. For each press, the vehicle goes about 1 km/h (1 mph) slower.
- The speedometer reading can be displayed in either English or metric units. See Instrument Cluster 0 83. The increment value used depends on the units displayed.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase the vehicle speed. When you take your foot off the pedal, the vehicle will slow down to the previous set cruise speed. While pressing the accelerator pedal or shortly following the release to override cruise control, briefly pressing −SET will result in cruise control set to the current vehicle speed.
Using Cruise Control on Hills
How well the cruise control works on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle speed. When going downhill, you might have to brake to keep your speed down. If the brake pedal is applied, cruise control will disengage.
Ending Cruise Control
There are five ways to end cruise control:
- Step lightly on the brake pedal.
- Press.
- Shift the electric drive unit to N (Neutral).
- Press to turn the cruise control system off completely.
- Activate Regen on Demand. See “Regen on Demand” under Regenerative Braking 0 184.
Erasing Speed Memory
The cruise control set speed is erased from memory if is pressed or if the vehicle is turned off.
Chevrolet Bolt EUV 2023 Top Accessories
[amalinkspro_table id=”32452″ new-window=”on” nofollow=”on” addtocart=”off” /]
Reference Links
View Full User Guide: Chevrolet Bolt EUV 2023 User
Download Manuals: https://www.chevrolet.com/support/vehicle/manuals-guides