2022 Chrysler Voyager Instrument Panel Information

The instrument panel of the 2022 Chrysler Voyager is a focal point within this elegant and family-friendly minivan. It functions as the command center for the vehicle’s sophisticated technology, providing drivers and passengers with easy-to-use access to vital information and controls. The instrument panel enhances the overall driving experience and reflects the Voyager’s commitment to safety, connectivity, and convenience with its contemporary design and user-friendly interface. In this introduction, we will examine the instrument panel of the 2022 Chrysler Voyager, highlighting how it contributes to the overall appeal and convenience of the vehicle.

BASE INSTRUMENT CLUSTER

BASE INSTRUMENT CLUSTER DESCRIPTIONS

Use this QR code to access your digital experience.

1. Tachometer
   1. Indicates the engine speed in revolutions per minute (RPM x 1000).
2. Instrument Cluster Display
   1. When the appropriate conditions exist, this display shows the instrument cluster display messages.
3. Speedometer
   1. Indicates vehicle speed.
4. Temperature Gauge
   1. The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.
   2. The gauge can indicate a higher temperature when driving in hot weather or up mountain grades. It should not be allowed to exceed the upper limits of the normal operating range.
      WARNING
      A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats.
      CAUTION
      Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reaches “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the gauge drops back into the normal range and is no longer red. If the gauge remains on the “H”, turn the engine off immediately and call an authorized dealer for service.
5. Fuel Gauge
   1. The gauge shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.
   2. The fuel pump symbol points to the side of the vehicle where the fuel door is located.

NOTE:
The warning/indicator lights will illuminate for a bulb check when the ignition is first cycled.

PREMIUM INSTRUMENT CLUSTER

PREMIUM INSTRUMENT CLUSTER DESCRIPTIONS

1. Tachometer
   1. Indicates the engine speed in revolutions per minute (RPM x 1000).
2. Instrument Cluster Display
   1. When the appropriate conditions exist, this display shows the instrument cluster display messages
3. Speedometer
   1. Indicates vehicle speed.
4. Temperature Gauge
   1. The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.
   2. The gauge can indicate a higher temperature when driving in hot weather or up mountain grades. It should not be allowed to exceed the upper limits of the normal operating range.
      WARNING
      A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats.
      CAUTION
      Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reaches “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the gauge drops back into the normal range and is no longer red. If the gauge remains on the “H”, turn the engine off immediately and call an authorized dealer for service.
5. Fuel Gauge
   1. The gauge shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.
   2. The fuel pump symbol points to the side of the vehicle where the fuel door is located.

INSTRUMENT CLUSTER DISPLAY

Your vehicle is equipped with an instrument cluster display, which offers useful information to the driver. With the ignition in the OFF position (and the key removed, for vehicles with mechanical key), opening/closing of a door will activate the display for viewing, and display the total miles or kilometres in the odometer. Your instrument cluster display is designed to display important information about your vehicle’s systems and features. Using a driver interactive display located on the instrument panel, your instrument cluster display can show you how systems are working and give you warnings when they are not. The steering wheel-mounted controls allow you to scroll through and enter the main menus and submenus. You can access the specific information you want and make selections and adjustments.

INSTRUMENT CLUSTER DISPLAY LOCATION AND CONTROLS

The vehicle’s instrument cluster is equipped with an instrument cluster display (base or premium cluster), which offers useful information to the driver.

1. Instrument Cluster Display Controls
2. Instrument Cluster Display Screen

The instrument cluster display controls allows the driver to select information by pushing the directional buttons mounted on the steering wheel:

Instrument Cluster Display Controls

1. Left Arrow Button
2. Up Arrow Button
3. Right Arrow Button
4. Down Arrow Button
5. OK Button

Back / Left Arrow Button
Push and release the left arrow button to access the information screens or submenu screens of a main menu item.

Up Arrow Button
Push and release the up arrow button to scroll upward through the Main Menu items.

Right Arrow Button
Push and release the right arrow button to access the information screens or submenu screens of a main menu item.

Down Arrow Button
Push and release the down arrow button to scroll downward through the Main Menu items.

OK Button
Push the OK button to access/select the information screens or submenu screens of a Main Menu item. Push and hold the OK button for two seconds to reset displayed/selected features that can be reset.

OIL LIFE RESET

Use this QR code to access your digital experience.

1. Your vehicle is equipped with an engine oil change indicator system. The “Oil Change Required” message will display for approximately five seconds after a single chime has sounded, to indicate it is time to change the engine oil. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.
2. Unless reset, this message will continue to display each time the ignition is cycled to the ON/RUN position.
3. To reset the oil change indicator after performing the scheduled maintenance, refer to the following procedure.

NOTE:
This procedure should only be performed after scheduled maintenance is completed. Resetting oil life other than when associated with a scheduled maintenance may result in damage due to not properly maintaining the engine oil.

Oil Life Reset

1. Without pressing the brake pedal, push the ENGINE START/STOP button and place the ignition in the ON/RUN position (do not start the vehicle.)
2. Push the OK button to enter the instrument cluster display menu screen.
3. Push and release the down arrow button to access the ”Vehicle Info” menu screen.
4. Push the left arrow button or right arrow button to access the “Oil Life” submenu.
5. Hold the OK button to reset the “Oil Life” to 100%.
6. Push the up arrow button to exit the instrument cluster display menu screen.

Secondary Method For Oil Life Reset Procedure

1. Without pushing the brake pedal, place the ignition in the ON/RUN position (do not start the engine).
2. Fully press the accelerator pedal, slowly, three times within 10 seconds.
3. Without pushing the brake pedal, place the ignition in the OFF position.

NOTE:
If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure.

KEYSENSE CLUSTER MESSAGES — IF EQUIPPED

When the KeySense key is in use there will be:

1. Continuous, dedicated telltale
2. Unique Display Splash Screen

With KeySense in use there will be multiple associated messages shown in the following table:

Setting	Instrument Cluster Display Message
None – With vehicle ignition ON	“KeySense in use. Max vehicle speed set to xx MPH/or km/h”
Max Vehicle Speed	“Max speed reached. KeySense in use” supported by a chime “Approaching max speed xx MPH/km/h” supported by a chime
Start Up Fuel Alert message	“Range to empty xxx miles or km”
Early Low Fuel Alert Message	“Fuel Low”
ParkSense	“Feature cannot be disabled .KeySense in use”

Setting	Instrument Cluster Display Message
Blind Spot	“Feature cannot be disabled .KeySense in use”
Forward Collision Warning	“Feature cannot be disabled. KeySense in use”

INSTRUMENT CLUSTER DISPLAY MENU ITEMS

The instrument cluster display can be used to view the main menu items for several features. Use the up and down arrow buttons to scroll through the driver interactive display menu options until the desired menu is reached.

NOTE
The instrument cluster displays menu items display in the centre of the instrument cluster. Menu items may vary depending on your vehicle’s features.

Speedometer
Push and release the up or down arrow button until the Speedometer is highlighted in the instrument cluster display. Push and release the OK button to toggle between MPH and km/h.

Vehicle Info

Push and release the up or down arrow button until Vehicle Info is highlighted in the instrument cluster display. Push the left or right arrow button to scroll through the following information submenus:

Tire Pressure
If tire pressure is OK for all tires, a vehicle ICON is displayed with tire pressure values in each corner of the ICON.
If one or more tires have low pressure, “Inflate Tire To XX” is displayed with the vehicle ICON, and the tire pressure values in each corner of the ICON with the pressure value of the low tire are displayed in a different color than the other tire pressure value. If the Tire Pressure system requires service, “Service Tire Pressure System” is displayed. Tire PSI is an information only function and cannot be reset.

Coolant Temp
Displays the actual coolant temperature.

Transmission Temp
Displays the actual transmission temperature.

Oil Temp
Displays the actual oil temperature.

Oil Pressure
Displays the actual oil pressure.

Oil Life
Displays the remaining engine oil life as a percentage. To reset the Oil Life, you must hold the OK button.
The “Hold OK to Reset” instruction will be displayed at all times, but the following conditions will need to be met in order to reset Oil Life:

1. The ignition must be in the ON/RUN position

If the conditions are met, holding the OK button will reset the gauge and the numeric display will return to 100%.
If the conditions are not met, a pop-up message will display for five seconds, describing the required conditions, and then the Oil Life screen will reappear.

Battery Voltage
Displays the actual battery voltage.

Engine Hours
Displays the number of hours of engine operation.

Driver Assist
Push and release the up or down arrow button until the Driver Assist display icon is highlighted in the instrument cluster display.

Fuel Economy

Push and release the up or down arrow button until the Fuel Economy Menu item is highlighted in the instrument cluster display. The Fuel Economy Menu will display the following:

1. Two submenu pages that can be toggled between using the left and right arrow buttons; one with Current Value displayed and one without the Current Value displayed:
   1. Average Fuel Economy (MPG, L/100 km, or km/L)
   2. Range To Empty (miles or km)
   3. Current Fuel Economy (MPG, L/100 km, or km/L)
   4. The Max and Min values will correspond to the particular engine requirements
2. Hold OK to reset average fuel economy information.

Trip Info
Push and release the up or down arrow button until the Trip Menu item is highlighted in the instrument cluster display. Push the left or right arrow button to scroll through the Trip A and Trip B submenus. The Trip information will display the following:

1. Distance
2. Average Fuel Economy
3. Elapsed Time
   Hold the OK button to reset feature information.

Stop / Start
Push and release the up or down arrow button until the Stop/Start menu title is displayed in the instrument cluster display.

Audio
Push and release the up or down arrow button until the Audio Menu displays in the instrument cluster display.

Messages
Push and release the up or down arrow button until Messages is highlighted in the instrument cluster display. This feature shows the number of stored warning messages. Pushing the right arrow button will allow you to see what the stored messages are.

NOTE
The pop-up messages indicate the status of the system and/or the conditions that need to be met. Messages remain in the stored stack until condition is cleared.

Screen Setup
Push and release the up or down arrow button until the Screen Setup Menu displays in the instrument cluster display. Push and release the OK button to enter the submenus. The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location that information is displayed.

Base Instrument Cluster Display Screen Setup Options:
1 — Upper Left	None Compass Outside Temp Time Range Current (MPG, L/100km, or km/L) Average (MPG, L/100km, or km/L)
2 — Upper Right	None Compass Outside Temp Time Range Current (MPG, L/100km, or km/L) Average (MPG, L/100km, or km/L)

Base Instrument Cluster Display Screen Setup Options:
3 — Center	None Compass Outside Temp Time Range Average (MPG, L/100km, or km/L) Current (MPG, L/100km, or km/L) Trip A Distance Trip B Distance Audio Menu Title Menu Title Digital Speed
4 — Defaults	Restore Cancel

Speed Warning — If Equipped

Push and release the up or down arrow button until the Speed Warning is highlighted in the instrument cluster display. Push and release the OK button to enter Speed Warning. Use the up  or down arrow button to turn the Speed Warning ON or OFF, then push and release the OK button to confirm the selection. If the ON  status is selected, use the up or down arrow button to set the desired speed, then push the OK button to set the speed for the Speed Warning. A Speed Warning telltale will illuminate in the instrument cluster, with a number matching the set speed, with a pop-up message to inform the driver that the Speed Warning has been set to the desired speed. Each time the set speed is exceeded, a single chime will sound and a pop-up warning message will display. If the set speed is exceeded more than 2 mph (3 km/h), a continuous chime will sound for up to 10 seconds, or until the speed is no longer exceeded. The telltale in the instrument cluster will also change from white to yellow, and a pop-up warning message will pop-up on the instrument cluster display.

NOTE
Speed Warning is unavailable while KeySense is in use.

FAQs

Useful Link

View Full PDF: 2022 Chrysler Voyager Owner’s Manual| Auto User Guide
2022 Chrysler Voyager Seat Setup Guide