2022-2023 Ducati Panigale V2 Seat Setup Instructions
With its stunning design and exceptional engineering, the 2022-2023 Ducati Panigale V2 is a high-performance sportbike that continues to captivate the affections of motorcycle enthusiasts. Riders frequently fail to notice the importance of the saddle when it comes to sportbikes. In addition to serving as a practical element, the saddle of the Panigale V2 is of paramount importance in promoting rider comfort throughout lengthy journeys and elevating the overall riding encounter.
This introductory section will provide a detailed examination of the seat on the 2022-2023 Ducati Panigale V2, with an emphasis on its aesthetic qualities, comfort functions, and the effect it exerts on the rider’s rapport with this extraordinary motorcycle. Irrespective of one’s passion for Ducatis or motorcycles, the Panigale V2’s seat is an essential component that significantly contributes to its distinctive attributes and overall performance.
Main Components and Devices
Position on the vehicle
- Tank filler plug.
- Seat lock.
- Side stand.
- Rear-view mirrors.
- Front fork adjusters.
- Rear shock absorber adjusters.
- Catalytic converter.
- Exhaust silencer.
Tank filler plug Opening
- Lift flap (1) and insert the key in the lock;
- Turn the key clockwise by 1/4 of a turn to release the lock;
- Lift the fuel tank plug (2).
Closing
- Close the plug (2) with the key inserted and push it down into its seat;
- Remove the key and close flap (1) protecting the lock.
Note
Plug can only be closed when key is inserted. Attention
After refuelling, always make sure that the plug is perfectly in place and closed.
Removing and refitting the seats
Use lock (1) to remove the passenger seat (2) and reach the tail guard compartment
Removing the passenger seat
- Insert the key into the lock (1);
- Turn the key counter clockwise until the passenger seat (2) catch disengages with an audible click;
- Pull the passenger seat (2) towards the front end of the vehicle until releasing it.
Refitting the passenger seat
- Before refitting the passenger seat (2), make sure that passenger strap (3) is correctly positioned.
- Slide the passenger seat (2) from vehicle front
(A) end towards the rear end (B) until hearing the catch click into place.
Attention
To close the seat cover insert it from the motorcycle side and slide it towards the rear side until hearing the engagement click.
Removing the rider seat
- Using the Allen wrench present in the tail guard compartment, loosen the two screws (4) on both sides of the rider seat (5);
- Slide the seat towards the rear end of the vehicle.
Refitting the rider seat
- Refit the rider seat (5) by first engaging the front end and then the rear end;
- Lift the rear edges of the seat and fasten it by tightening screws (4).
- Check proper rider seat fastening by trying to raise its front end.
After removing the rider seat, you can reach the battery maintaining connector (6).
Maintaining the battery charge
Your motorcycle is equipped with a connector (1) to which you can connect a special battery charger (2)(Battery maintainer kit part no. 69924601A – various countries; Battery maintainer kit part no. 69924601AX – for Japan, China and Australia only) available from our sales network.
To access it, remove the rider seat as described in chapter “Removing and refitting the seats”.
Attention
The electric system of this motorcycle is designed so as to ensure there is a very low power drain when the motorcycle is OFF. Nevertheless, the battery features a certain self-discharge rate that is normal and depends on ambient conditions as well as on vehicle “non-use” time.
Important
If battery is not kept at a minimum charge level by a suitable battery charge maintainer, sulphation may occur and this is an irreversible phenomenon causing decreasing battery performance.
Note
When the motorcycle is left unused (approximately for more than 30 days). We recommend owners to use the Ducati battery charge maintainer (Battery maintainer kit part no. 69924601A – various countries; Battery maintainer kit part no. 69924601AX – for Japan, China and Australia only) since its electronics monitors the battery voltage and features a maximum charge current of 1.5 Ah. Connect the maintainer to the diagnostics socket located in the rear side of the motorcycle.
Note
Using charge maintainers not approved by Ducati could damage the electric system; motorcycle warranty does not cover the battery if damaged due to failure to comply with the above indications, since it is considered as wrong maintenance.
Side stand
Important
Place the motorcycle on the side stand only when you are not going to use it for short periods of time. Before lowering the side stand, make sure that the bearing surface is hard and flat.
Do not park on soft or pebbled ground or on asphalt melted by the sun, etc. or else the motorcycle may fall over. When parking downhill, always position the motorcycle with the rear wheel facing downhill. To pull down the side stand, hold the motorcycle handlebars with both hands and push down on the side stand (1) with your foot until it is fully extended. Tilt the motorcycle until the side stand is resting on the ground.
To move the side stand to its rest position (horizontal position), lean the motorcycle to the right while lifting the thrust arm (1) with your foot.
To ensure trouble-free operation of the side stand joint, thoroughly clean it and then use SHELL Alvania R3 grease to lubricate all friction points.
Attention
Do not sit on the motorcycle when it is supported on the side stand.
Note
Check for proper operation of the stand mechanism (two springs, one into the other) and the safety sensor (2) at regular intervals.
Note
It is possible to start the engine with stand unfolded and gearbox in neutral.
Bluetooth control unit
The motorcycle can be equipped with a Bluetooth control unit that works as a hub between the various supported electronic devices relying on a Bluetooth communication interface.
The Bluetooth control unit, which is not installed in this vehicle, can be purchased at a Ducati Dealer or Authorised Service Centre.
Attention
Smartphone and Bluetooth Headset device manufacturers may incorporate certain changes within the standard protocols over the course of the lifecycle of the device (Smartphones and Earphones).
Attention
These changes are outside the control of Ducati and may result in Bluetooth Headset devices functionality becoming impaired (sharing Music, multimedia player, etc.) and may equally affect some types of Smartphones (depending on supported Bluetooth profiles). This is why Ducati cannot guarantee multimedia player proper operation for:
- Any earphones not coming with the “Ducati Kit part no. 981029498”;
- Any Smartphones not supporting the required Bluetooth profiles (even though paired to earphones coming with the “Ducati Kit part no. 981029498”).
Attention
In case of interference or noise due to particular conditions of the external environment, the Ducati earphone kit part no. 981029498 also allows sharing the music being played directly from rider helmet to passenger helmet (for further details please refer to the manual of the earphones coming with the Ducati kit part no. 981029498).
Note
The Ducati kit part no. 981029498 can be purchased separately at a Ducati Dealer or Authorised Service Centre.
Check that your Smartphone supports the following profiles:
- MAP profile: for a correct display of SMS and MMS notifications;
- PBAP profile: for a correct display of the Smartphone contact list.
Attention
Ducati does not ensure a correct connection to the Ducati Multimedia System of Bluetooth navigators that are not provided in the following kits:
- Kit of Ducati Zumo satellite navigator 350
- Kit of Ducati Zumo satellite navigator 390
- Kit of Ducati Zumo satellite navigator 395
Note
The Ducati kits mentioned above can be purchased separately at a Ducati Dealer or Authorised Service Centre.
Steering damper
It is located before the handlebar and is secured to the steering head.
It provides stable and accurate steering, improving the motorcycle’s handling response under any conditions
FAQs
No, the Ducati Panigale V2 does not have an adjustable backrest. A fixed position is included to optimise performance and cycling comfort.
The saddle height of the Ducati Panigale V2 for the 2022-2023 model year is roughly 33.1 inches (840 mm).
Indeed, aftermarket seats for the Panigale V2 are available for those who desire to improve the seat’s comfort or aesthetic appeal.
Fabricated from resilient and long lasting materials, the saddle of the Panigale V2 is commonly constructed from synthetic leather and foam padding to ensure the comfort of the rider.
Although the Panigale V2 is predominantly a sportbike, the seat is constructed to strike a balance between sportiness and comfort, making it appropriate for journeys of moderate to short duration.
Indeed, the seat is equipped with foam padding to afford the passenger a satisfactory degree of comfort even when engaging in vigorous rides.
Utilise a soft cloth and a mild, nonabrasive cleanser to maintain and clean the seat. Prevent damage to the upholstery of the seat by avoiding abrasive or harsh substances.
Useful Link
View Full PDF :Ducati Panigale V2 2022-2023 User Manual| Auto User Guide