2022 Ducati Supersport 950 Seat Setup Instructions
Sportbike model year 2022, the Ducati Supersport 950 features a versatile and pleasant seating arrangement in addition to its exceptional performance. Designed by the renowned Italian motorcycle manufacturer Ducati, this model is intended to provide an exhilarating riding experience without sacrificing the rider’s convenience. The 2022 Ducati Supersport 950 features a seat configuration that harmonises athletic ergonomics with all-day comfort, rendering it an optimal selection for vigorous weekend excursions as well as routine commuting. This introduction will examine the primary characteristics of the seat configuration on the 2022 Ducati Supersport 950, emphasising its capacity to provide motorcyclists who require the utmost in comfort and performance with an optimal balance. Whether you ride on a daily basis or are an avid devotee, the seat configuration of this Ducati model is certain to enhance your riding experience and make a lasting impression.
Main Components and Devices
Position on the vehicle
- Tank filler plug.
- Seat lock.
- Side stand.
- Rear-view mirrors.
- Front fork adjusters.
- Rear shock absorber adjusters.
- Catalytic converter.
- Exhaust silencer.
Tank filler plug Opening
- Lift flap (1) and insert the key in the lock;
- Turn the key clockwise by 1/4 of a turn to release the lock;
- Lift the fuel tank plug (2).
Closing
- Close the plug (2) with the key inserted and push it down into its seat;
- Remove the key and close flap (1) protecting the lock.
Note
Plug can only be closed when key is inserted.
Attention
After refuelling, always make sure that the plug is perfectly in place and closed.
Seat lock
Removing the seat
Insert the key in lock (1), turn clockwise while pressing down at the latch (3) to help release the pin. Slide the seat (2) to the rear after removing the front retaining tabs (A) from the tank su pport bracket (B).
After removing the seat, you can reach the battery maintainer connector (C).
To use it, remove the cover and connect the connector (C) to maintainer (4), as described in chapter “Maintaining the battery charge”.
Refitting the seat
Make sure that all elements are correctly positioned and fastened to the compartment under the seat (2). Insert the retaining tabs (A), at the front end of the seat, into the tank support bracket (B) fixed to the rear subframe.
By keeping the rear part of the seat raised, insert the latch (3) into the lock (4), by pressing on the seat: push the seat rear end until you hear the lock (4) click into place.
Make sure the seat is safely secured to the frame and remove the key from the lock.
Maintaining the Battery Charge
Your motorcycle is equipped with a connector (1) to which you can connect a special battery charger (2)(Battery maintainer kit part no. 69924601A – various countries; Battery maintainer kit part no. 69924601AX – for Japan, China and Australia only) available from our sales network.
To access it, remove the rider seat as described in chapter “Removing and refitting the seats”.
Note
The electric system of this model is designed so as to ensure there is a very low power drain when the motorcycle is OFF. Nevertheless, the battery features a certain self-discharge rate that is normal and depends on ambient conditions as well as on “non-use” time.
Attention
The electric system of this motorcycle is designed so as to ensure there is a very low power drain when the motorcycle is OFF. Nevertheless, the battery features a certain self-discharge rate that is normal and depends on ambient conditions as well as on vehicle “non-use” time.
Important
If battery is not kept at a minimum charge level by a suitable battery charge maintainer, sulphation may occur and this is an irreversible phenomenon causing decreasing battery performance.
When the motorcycle is left unused (approximately for more than 30 days). We recommend owners to use the Ducati battery charge maintainer (Battery maintenance kit) since its electronics monitors the battery voltage and features a maximum charge current of 1.5 Ah. Connect the battery maintainer to the diagnostic socket.
Helmet cable
The helmet cable (1) is inside the tool box, refer to “Tool kit and accessories”. Route cable through helmet and engage cable end into pin (2).
Leave the helmet hanging and refit the seat to hold it in place.
Attention
This device protects the helmet against theft when the motorcycle is parked. Do not leave the helmet attached when riding the motorcycle; it could interfere with your movements and cause loss of control of the motorcycle.
Side Stand
Important
The position of the side stand is identified on the instrument panel by the warning light (A). When the warning light is on, the side stand is lowered (and the engine start is inhibited).
Attention
Before lowering the side stand, make sure that the bearing surface is hard and flat.
Do not park on soft or pebbled ground or on asphalt melt by the sun heat and similar or the motorcycle may fall over.
When parking downhill, always position the motorcycle with the rear wheel facing downhill. To pull down the side stand, hold the motorcycle handlebars with both hands and push down on the side stand (1) with your foot until it is fully extended. Tilt the motorcycle until the side stand is resting on the ground.
Attention
Do not sit on the motorcycle when it is supported on the side stand.
To move the side stand to its resting position
(horizontal position), lean the motorcycle to the right while lifting the side stand (1) with your foot.
To ensure trouble-free operation of the side stand joint, thoroughly clean it and then use SHELL Alvania R3 grease to lubricate all friction points.
Note
The engine can be started with the side stand down and the gearbox in neutral. If starting with a gear engaged, pull in the clutch lever (in this case the side stand must be up before engaging the gear).
FAQs
A two-up seat that is both agile and comfortable, accommodating both the rider and passenger.
Is the seat height adjustable on the Supersport 950?
Seat height adjustment is not possible. It maintains a constant height.
Although the seat is constructed to adequately support riders of varying heights, this is indeed the case.
Indeed, the seat configuration has been thoughtfully engineered to deliver optimal comfort during extended journeys, rendering it well-suited for touring purposes.
Concerning the material of the seat cover, it is constructed from resilient, long-lasting materials to ensure both comfort and longevity.
Its primary objective is to provide the passenger with a secure and comfortable travelling experience.
Indeed, the passenger seat can be removed to achieve a solo rider appearance of the bicycle.
Additionally, the seat is padded to a high standard to ensure the convenience of both the rider and the passenger.
The Supersport 950 seat material is constructed with water resistance in mind, safeguarding it against mild precipitation or moisture.
Indeed, the seat’s design prioritises comfort while ensuring sufficient capacity for both the rider and passenger.
Useful link
View full PDF : Ducati Supersport 950 2022| Auto User Guide
2022 Ducati Supersport 950 Warning and Indicators Guide