Auto User Guide

2016-2023 Harley Davidson Street Headlamps Guide

Harley Devidson logo2016-2023 Harley Davidson Street Headlamps Guide

A remarkable innovation in headlight design was debuted with the 2016–2023 Harley Davidson Street series, fusing vintage Harley styling with cutting-edge lighting technology. These headlamps had a distinctive, outlandish design that made them part of the Street series and made them easily visible on the road.

These headlamps focused on both form and function, illuminating the road ahead while bringing a bit of Harley’s recognizable personality to every ride. These headlamps became a crucial component of the Harley Davidson Street’s timeless appeal, whether riding on city streets or the open road.

HEADLAMP

Checking Headlamp Alignment

  1. Check tire pressure. Refer to Table 20.
  2. Adjust rear shocks for the rider and intended load. See BEFORE RIDING.
  3. Fill fuel tank or add an equal amount of ballast.
    NOTE
    Choose a wall in minimum light.
  4. See Figure 39. Park the motorcycle in a line (1) perpendicular to the wall.
  5. Position motorcycle with front axle 7.6 m (25 ft) from wall.
  6. Draw a vertical line (2) on the wall.
  7. Point the front wheel straight forward at the wall.
  8. Measure the distance (4) from the floor to the center of the high beam bulb.
  9. Activate high beam. Verify headlamp alignment.
  10. Adjust if necessary.

 

2016-2023 Harley Davidson Street Headlamps Guide (1)

  1. Perpendicular line
  2. Vertical line
  3. 7.6 m (25 ft)
  4. High beam bulb centerline
  5. Horizontal line 53.3 mm (2.1 in) lower than bulb centerline

Figure 39. Checking Headlamp Alignment

Adjusting Headlamp
Set Horizontal Adjustment

  1. See Figure 40. Remove speed screen screws (1) and washers (2).
  2. Pull speed screen away from upper speed screen bracket (4).
  3. Pull speed screen way from lower speed screen bracket (5) to remove posts (6) from grommets.
  4. See Figure 41. Loosen horizontal adjustment locknut (1).
  5. Direct light beam straight ahead.
  6. Tighten horizontal adjustment locknut to 27.5-32.5 Nm (20.3-32.5 ft-lbs).
    NOTE
    Perform all adjustments before installing speed screen.
  7. See Figure 40. Align posts of speed screen (3) with grommets.
  8. Install speed screen onto lower speed screen bracket (5).
  9. Align speed screen to upper speed screen bracket (4).
  10. Install washers (2) and screws (1). Tighten to 2.3-3.3 Nm (21-29 in-lbs).

Set Vertical Adjustment

  1. See Figure 41. Loosen locknut (1) for vertical adjustment bolt (2)
  2. Aim headlamp at horizontal line on wall.
  3. Tighten vertical adjustment locknut to 20.6-25.5 Nm (16-18 ft-lbs).

2016-2023 Harley Davidson Street Headlamps Guide (2)

  1. Screw (2)
  2. Washer (2)
  3. Speed screen
  4. Upper speed screen bracket
  5. Lower speed screen bracket
  6. Post (2)

Figure 40. Headlamp Speed Screen

2016-2023 Harley Davidson Street Headlamps Guide (3)

  1. Vertical adjustment locknut
  2. Vertical adjustment bolt
  3. Horizontal adjustment locknut

Figure 41. Headlamp Adjustment

Replacing Headlamp or Position Bulb
The automatic-on headlamp feature provides increased visibility of the rider to other motorists. Be sure headlamp is on at all times. Poor visibility of rider to other motorists can result in death or serious injury. (00030b)

  1. See Figure 40. Remove screws (1) and washers (2).
  2. Pull speed screen away from upper speed screen bracket (4).
  3. Pull speed screen way from lower speed screen bracket (5) to remove posts (6) from grommets.
  4. Remove main fuse. See SERVICE PROCEDURES, Fuses and Relays.
  5. See Figure 42. Remove screws (6).
  6. Pull lens assembly (5) from headlamp housing.
  7. Disconnect electrical connectors from headlamp and position bulbs.
  8. Loosen screw (2).
  9. Remove retainer (3).
  10. Remove headlamp bulb (4).
  11. Remove position bulb (7).
  12. Install new headlamp or position bulb.
  13. Install retainer (3).
  14. Tighten screw (2).
  15. Connect electrical connectors to headlamp and position bulbs.
  16. Attach lens assembly (5) to headlamp housing.
  17. Install screws (6).
  18. See Figure 40. Align posts of speed screen (3) with grommets.
  19. Install speed screen onto lower speed screen bracket (5).
  20. Align speed screen to upper speed screen bracket (4).
  21. Install washers (2) and screws (1). Tighten to 2.3-3.3 Nm (21-29 in-lbs).
  22. Install main fuse. See SERVICE PROCEDURES, Fuses and Relays.

WAENING
Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a) 23. Check operation of all lamps.

2016-2023 Harley Davidson Street Headlamps Guide (4)

  1. Boot
  2. Screw
  3. Retainer
  4. Headlamp bulb
  5. Lens assembly
  6. Screw (2)
  7. Position bulb

Figure 42. Headlamp Bulb

FAQs

What type of headlamp does the 2016-2023 Harley Davidson Street come equipped with?

Halogen headlamps are the norm for the Harley Davidson Street from 2016 to 2023.

Can I upgrade the halogen headlamp to an LED one on my Harley Davidson Street?

Yes, you may change your headlamp to an LED to have better visibility and brightness. There are several aftermarket choices.

What is the purpose of the Daymaker LED headlamp available for some models?

The Daymaker LED headlight is made to enable nighttime riding with enhanced illumination that enhances visibility and safety.

How do I adjust the headlamp beam on my Harley Davidson Street?

Find the adjustment screws on the headlamp housing and turn them to change the headlamp beam. To correctly align the beam, turn them.

Are there different headlamp options for different Harley Davidson Street models within this period?

According to the particular model and trim level, headlight designs and features may vary.

What is the lifespan of a typical Harley Davidson Street headlamp bulb?

While LED lights can last far longer—often tens of thousands of hours—than halogen bulbs, which typically last between 500 and 1,000 hours.

Can I use LED headlamp bulbs in a Harley Davidson Street that originally came with halogen bulbs?

Yes, you can convert to LED headlamp bulbs, but for compatibility you might require other parts like an LED headlamp conversion kit.

Do Harley Davidson Street headlamps have a warranty?

Depending on the type and manufacturer, headlamp warranties can change. For precise warranty information, consult your owner’s manual or get in touch with the dealership

How do I replace a burnt-out headlamp bulb on my Harley Davidson Street?

For step-by-step directions on changing the headlamp bulb, go to your owner’s handbook. Typically, it entails taking off the headlight housing.

Are there any regulations regarding the brightness of aftermarket headlamp bulbs on motorcycles?

Yes, there are laws in many places that set limits on how bright headlight bulbs can be. Verify that your upgrades adhere to applicable local legislation.

What are the advantages of LED headlamps over halogen ones for Harley Davidson Street motorcycles?

LED headlamps are more energy-efficient, produce brighter illumination, and have a longer lifespan than halogen bulbs.

Can I customize the appearance of my Harley Davidson Street’s headlamp?

Yes, you can change the look of the headlamp by installing ornamental bezels, covers, or other aftermarket items.

What should I do if my headlamp lens is cracked or damaged?

To maintain visibility and safety on the road, replace the damaged headlamp lens as soon as possible.

Are there headlamp options that come with integrated auxiliary lights for improved visibility?

It’s true that some aftermarket headlamp alternatives have incorporated auxiliary lights that can improve vision, particularly in low light.

Is it necessary to have a professional install an upgraded headlamp on my Harley Davidson Street?

Although upgrading a headlight can be done on your own, having it professionally installed is advised to ensure appropriate wiring and alignment.

Useful Link

View Full PDF : Harley Davidson Street 2016-2023 User Manual |Auto User Guide
Specifications : 2016-2023 Harley Davidson Street Specifications

Leave a Reply

Your email address will not be published. Required fields are marked *