2020 Honda Insight Fuses and Fuse Box | Fix a Blown Fuse at your Home
The hybrid car Honda Insight 2020 is known for using little gas and having eco-friendly features. It has a complex electrical system that is controlled by many fuses. For the Honda Insight 2020, the fuse box is very important for protecting the car’s electrical parts by stopping overloads and short circuits. It is important to know how the fuse box is set up to keep and fix electrical problems. If a fuse blows, it is very important to find the bad fuse and change it so that the system works again. The fuse box usually has a map that shows what each fuse does, which helps owners figure out where the problem is coming from. If you know what you’re doing and are careful, replacing a blown fuse in your Honda Insight 2020 at home can be a simple task that will keep it running smoothly and reliably.
Fuse Locations
If any electrical devices are not working, set the power mode to VEHICLE OFF and check to see if any applicable fuse is blown.
Engine Compartment Fuse Box Type A
Located near the washer fluid. Push the tabs to open the box.
Fuse locations are shown on the fuse box cover. Locate the fuse in question by the fuse number and box cover number.
Circuit-protected and fuse rating
Circuit Protected | Amps | |
1 | MAIN FUSE | 150 A |
IG MAIN 1 | 30 A | |
SUB FAN MTR | 30 A | |
IG MAIN 2 | 30 A | |
OP FUSE MAIN | 30 A | |
ESB | 40 A | |
ENG EWP | 30 A | |
2 | WIPER MOTOR | 30 A |
R/M 2 | 30 A | |
P-ACT | 30 A | |
R/M 1 | 30 A | |
COOLING FAN | 30 A | |
EPS | 70 A | |
3 | BLOWER MOTOR | 40 A |
ABS/VSA MOTOR | 40 A | |
FUSE BOX OPTION* | (40 A) | |
ABS/VSA FSR | 40 A | |
PREMIUM AUDIO* | (30 A) | |
REAR DEFROSTER | 40 A | |
4 | − | 30 A |
− | 30 A | |
FUSE BOX 2 | 40 A | |
FUSE BOX 1 | 60 A | |
5 | IGPS | 7.5 A |
6 | VBU | 10 A |
7 | IG HOLD1 | 10 A |
8 | PCU EWP | 10 A |
9 | IGP | 15 A |
10 | BACK UP | 10 A |
11 | IGPS (LAF) | 7.5 A |
12 | EVTC | 20 A |
13 | HAZARD | 10 A |
14 | IG COIL | 15 A |
15 | DBW | 15 A |
16 | STOP LIGHTS | 10 A |
17 | − | − |
18 | − | − |
19 | AUDIO | 15 A |
20 | FR FOG LIGHT* | (15 A) |
21 | AS P/SEAT RECLINING* | 20 A |
22 | AS P/SEAT SLIDE* | 20 A |
23 | HORN | 10 A |
24 | WASHER | 15 A |
25 | SHIFTER | 10 A |
26 | SMART | 10 A |
27 | − | − |
28 | P-ACT UNIT | 10 A |
29 | IGB | 10 A |
30 | − | − |
Engine Compartment Fuse Box Type B
Fuse locations are shown on the fuse box cover. Locate the fuse in question by the fuse number and box cover number. Push the tabs to open the box.
Engine Compartment Fuse Box Type B
Circuit-protected and fuse rating
Circuit Protected | Amps | |
1 | PTC2 | 40 A |
PTC4 | 40 A | |
− | 40 A | |
− | 40 A | |
− | 40 A | |
− | 30 A | |
2 | BATT SNSR | 7.5 A |
3 | − | (7.5 A) |
4 | − | − |
5 | AUDIO SUB* | (7.5 A) |
6 | − | − |
7 | RR H/SEAT* | (15 A) |
Interior Fuse Box Type A
Located on a 12-volt battery in the center console.
Replacement of this fuse should be done by a dealer.
Circuit-protected and fuse rating
Circuit Protected | Amps | |
1 | BATTERY FUSE | 175 A |
Interior Fuse Box Type B
Located under the dashboard.
Fuse locations are shown on the label on the side panel.
Locate the fuse in question by the fuse number and label number.
Circuit-protected and fuse rating
Circuit Protected | Amps | |
1 | ACC | 10 A |
2 | − | − |
3 | BATT ECU | 10 A |
4 | SHIFTER | 5A |
5 | OPTION | 10 A |
6 | P-ACT | 5A |
7 | METER | 10 A |
8 | FUEL PUMP | 15 A |
9 | AIRCON | 10 A |
10 | − | − |
11 | IG1 MON | 5 A |
12 | R-SIDE DOOR LOCK | 10 A |
13 | L SIDE DOOR UNLOCK | 10 A |
14 | RR L P/W | 20 A |
15 | AS P/W | 20A |
16 | DOOR LOCK | 20A |
17 | VBSOL | 7.5A |
18 | − | − |
19 | SUNROOF | 20 A |
20 | ESB | 5 A |
21 | ACG | 10 A |
22 | DRL | 7.5A |
23 | − | − |
24 | − | − |
25 | DR DOOR LOCK | 10 A |
26 | R SIDE DOOR UNLOCK | 10 A |
27 | RR R P/W | 20A |
28 | DR P/W | 20A |
29 | FR ACC SOCKET | 20 A |
30 | OPTION | 10 A |
31 | DR P/SEAT REC* | 20 A |
32 | FR SEAT HEATER* | 20 A |
33 | DR P/SEAT SLI* | 20 A |
34 | ABS/VSA | 10 A |
35 | SRS | 10 A |
36 | HAC OP | 20 A |
37 | BATT FAN | 15A |
38 | L SIDE DOOR LOCK | 10 A |
39 | DR DOOR UNLOCK | 10 A |
Inspecting and Changing Fuses
- Set the power mode to VEHICLE OFF. Turn headlights and all accessories off.
- Remove the fuse box cover.
- Check the large fuse in the engine compartment.
- If the fuse is blown, use a Phillips-head screwdriver to remove the screw and replace it with a new one.
- Inspect the small fuses in the engine compartment and the vehicle interior.
- If there is a blown fuse, remove it with the fuse puller and replace it with a new one.
- Check the large fuse in the vehicle interior.
- If the fuse is blown, use a Phillips-head screwdriver to remove the screw and replace it with a new one.
- Inspect the small fuses in the vehicle interior.
- If there is a burned-out fuse, remove it with the fuse puller and replace it with a new one.
NOTICE
Replacing a fuse with one that has a higher rating greatly increases the chances of damaging the electrical system.
Replace the fuse with a spare fuse of the same specified amperage.
Use the charts to locate the fuse in question and confirm the specified amperage on the fuse label. 2 Fuse Locations There is a fuse puller on the back of the cover of the engine compartment fuse box type A.
FAQs
The fuse box in the Honda Insight 2020 is typically located in the engine compartment.
Open the hood and look for the fuse box near the battery. There should be a cover that can be removed to access the fuses.
The colors of the fuses often indicate their amperage rating.
Visually inspect the fuses. If the metal strip inside the fuse is broken, it’s likely blown.
You usually only need a pair of needle-nose pliers or a fuse puller to remove the blown fuse.
It’s crucial to use a fuse with the correct amperage rating.
The amperage rating is often stamped on the top or end of the fuse.
Some vehicles come with spare fuses stored in the fuse box. Check for a compartment or storage area within the box.
Fuses protect various electrical components, including lights, radios, power windows, and other accessories.
No, using a higher amperage fuse can lead to electrical damage or fire. Always use the specified amperage rating.
There may be an underlying issue. Consult a mechanic or dealership for a professional diagnosis.
Yes, replacing a fuse is a relatively simple task. Follow the instructions.
Ensure the car is turned off, and wear protective gloves. Remove the negative battery cable before replacing the fuses for added safety.
If you’re unsure or the problem persists, it’s best to seek professional help from a certified mechanic or the dealership.
Inspect the fuses visually. If the metal strip inside the fuse is broken, it’s likely blown. You can also use a multimeter to check for continuity.
Useful Link:
View Full PDF: Honda Insight 2020 User Manual | Auto User Guide