2021 Honda Insight Fuses and Fuse Box Instructions
Introduction
Every modern marvel contains a secret realm of electricity where the technology symphony orchestrates the flawless operation of every component. Welcome to the world of fuses and the fuse box in the 2021 Honda Insight, where protection and accuracy join together to guarantee an unparalleled driving experience. Meet the fuses, the unsung warriors that protect the sophisticated electrical system of your Insight. These tiny but powerful machines serve as gatekeepers, vigilantly observing the movement of electric current. Fuse bravely sacrifice themselves to shield your car from potential injury when sudden surges threaten to upset the harmony.
A technology hub emerges from within the fuse box’s boundaries. In this case, a variety of fuses work together to control power distribution, making it possible for everything from the slick infotainment system to the lights that directs you to operate. Every circuit finds its conductor in the fuse box, which serves as the control hub and ensures that every function operates precisely and consistently. The fuse box is your entrance to the brain of your Insight’s electrical design, and it is situated in a convenient yet modest location. You can reach this hub of technology with the power of comprehending, identifying problems and skillfully regaining functionality. The fuse box is a gateway to a world of educated control, not just a physical object.
Fuses
Fuse Locations
If any electrical devices are not working, set the power mode to VEHICLE OFF and check to see if any applicable fuse is blown.
Engine Compartment Fuse Box Type A
Located near the washer fluid. Push the tabs to open the box.
Fuse locations are shown on the fuse box cover. Locate the fuse in question by the fuse number and box cover number.
Circuit Protected and Fuse Rating
|
1 |
MAIN FUSE |
150 A |
|
IG MAIN 1 |
30 A |
|
|
SUB FAN MTR |
30 A |
|
|
IG MAIN 2 |
30 A |
|
|
OP FUSE MAIN |
30 A |
|
|
ESB |
40 A |
|
|
ENG EWP |
30 A |
|
|
|
FUSE BOX 2 |
40 A |
|
5 |
IGPS |
7.5 A |
|
|
6 |
VBU |
10 A |
|
|
7 |
IG HOLD1 |
10 A |
|
|
8 |
PCU EWP |
10 A |
|
|
9 |
IGP |
15 A |
|
|
10 |
BACK UP |
10 A |
|
|
11 |
IGPS (LAF) |
7.5 A |
|
|
12 |
EVTC |
20 A |
|
|
13 |
HAZARD |
10 A |
|
|
14 |
IG COIL |
15 A |
|
|
15 |
DBW |
15 A |
|
|
16 |
STOP LIGHTS |
10 A |
|
|
17 |
− |
− |
|
|
18 |
− |
− |
|
|
19 |
AUDIO |
15 A |
|
|
|
20 |
FR FOG LIGHT* |
(15 A) |
Engine Compartment Fuse Box Type B
Fuse locations are shown on the fuse box cover. Locate the fuse in question by the fuse number and box cover number. Push the tabs to open the box.
Circuit Protected and Fuse Rating
|
1 |
PTC2 |
40 A |
|
PTC4 |
40 A |
|
|
− |
40 A |
|
|
− |
40 A |
|
|
− |
40 A
|
|
|
− |
30 A |
Interior Fuse Box Type A
Located on 12-volt battery in the center console.
Replacement of this fuse should be done by a dealer.
Circuit Protected and Fuse Rating
Interior Fuse Box Type B
Located under the dashboard.
Fuse locations are shown on the label on the side panel.
Locate the fuse in question by the fuse number and label number.
Circuit Protected and Fuse Rating
Inspecting and Changing Fuses
- Set the power mode to VEHICLE OFF. Turn headlights and all accessories off.
- Remove the fuse box cover.
- Check the large fuse in the engine compartment.
- If the fuse is blown, use a Phillips-head screwdriver to remove the screw and replace it with a new one.
- Inspect the small fuses in the engine compartment and the vehicle interior.
- If there is a blown fuse, remove it with the fuse puller and replace it with a new one.
- Check the large fuse in the vehicle interior.
- If the fuse is blown, use a phillips-head screwdriver to remove the screw and replace it with a new one.
- Inspect the small fuses in the vehicle interior.
- If there is a burned out fuse, remove it with the fuse puller and replace it with a new one.
- Replacing a fuse with one that has a higher rating greatly increases the chances of damaging the electrical system.
NOTICE
Replace fuse with a spare fuse of the same specified amperage.
Use the charts to locate the fuse in question and confirm the specified amperage on the fuse label.
Fuse Locations
There is a fuse puller on the back of the cover of the engine compartment fuse box type A.
FAQs
A fuse is a safety feature that stops the flow of electricity if a circuit experiences overload or a fault, preventing harm to the car’s electrical systems.
The fuse box in the 2021 Honda Insight is usually found within the vehicle, usually next to the dashboard or on the driver’s side.
To reach the fuse box, remove the lid from the relevant compartment, which is typically labeled “FUSE” or “FUSE BOX,” and follow the directions in your owner’s handbook.
Blade-type fuses and tiny fuses, each created to protect a separate electrical component, may be used in the 2021 Honda Insight.
You could notice that the associated electrical component (such as the lights or radio) is not working if a fuse blows. The fuse can be examined visually or its continuity tested using a multimeter.
Yes, you can do it yourself if a fuse blows. Use the included fuse remover to remove the old fuse, then put in a new fuse with the same rating after consulting your owner’s manual to determine the right fuse.
The proper fuse rating is typically stated in your owner’s manual or on the fuse box cover. It’s crucial to match the exact rating since using a fuse with the incorrect rating can cause electrical problems or possibly a fire.
Yes, changing a blown fuse often solves an electrical problem. But if the fuse keeps blowing, it can be an indication of a bigger issue that has to be diagnosed by a professional.
Some cars come with extra fuses that are kept within the fuse box lid or in a special place inside the car. The information about extra fuses can be found in your owner’s manual.
No, it is not advised to use a higher-rated fuse because doing so could harm the car’s electrical system or even be dangerous. Use the proper fuse rating at all times.
It’s possible that the 2021 Honda Insight may use specialized fuses to protect various electrical systems and components. For information on the precise fuse positions, consult your owner’s manual or the fuse box lid.
In general, it is not advised to install more electrical components by tapping into existing fuses because this could overload the circuit. If you want to include additional components, it is preferable to get professional advice.
It’s recommended to have your vehicle checked out by a trained mechanic if fuses are blowing often. The failures can be the result of an underlying problem.
It is safest to fix the problem before driving, especially at night or in bad weather, if a fuse for a crucial component (such as the headlights or brake lights) has blown.
Check your fuses frequently for signs of wear or damage. Keep the fuse box clear of clutter and clean. If you’re unsure about any electrical matters, seek advice from your owner’s manual or a qualified mechanic.
Useful Links
Download Manual: Manuals and Warranty | MyGarage | Honda
View Full Manual: 2021 Honda Insight User Manual | Auto User Guide