2022 Honda Insight Engine Oil and Fluids

Introduction

The engine oil and fluids system on the 2022 Honda Insight has been precisely constructed to guarantee peak performance and lifespan. The engine oil in the 2022 Insight is designed with an emphasis on efficiency and environmental awareness to offer superior lubrication, heat dissipation, and protection for the engine’s complicated components. Beyond just the engine oil, the vehicle’s sophisticated fluid technology also includes transmission fluid, brake fluid, and coolant, all of which are precisely calibrated to maintain top performance. These premium fluids help the Insight achieve great fuel efficiency and low emissions, combining innovation and environmental friendliness in a seamless way.

Engine Oil and Fluids

Recommended Engine Oil
Use a genuine engine oil or another commercial engine oil of suitable type and viscosity (for the ambient temperature) as shown in the image that follows.
Oil is a major contributor to your engine’s performance and longevity. If you drive the vehicle with insufficient or deteriorated oil, the engine may fail or be damaged.

Formulated to improve fuel economy

Synthetic Oil
You may also use synthetic motor oil if it is labeled with the API Certification Seal and is the specified viscosity grade.

Engine Oil Additives

• Your vehicle does not require oil additives. In fact, they may adversely affect the engine performance and durability.
  The following seal indicates the oil is energy conserving and that it meets the American Petroleum Institute’s latest requirements.

Oil Check

• We recommend that you check the engine oil level every time you refuel.
• Park the vehicle on level ground.

Turn off the power system. You can check the oil level without the engine having run beforehand. If the engine has been running, wait approximately three minutes before you check the oil.

1. Remove the dipstick (orange).
2. Wipe the dipstick with a clean cloth or paper towel.
3. Insert the dipstick back all the way into its hole.
4. Remove the dipstick again, and check the level. It should be between the upper and lower marks. Add oil if necessary.

Oil Check
If the oil level is near or below the lower mark, slowly add oil, being careful not to overfill.

Adding Engine Oil

1. Unscrew and remove the engine oil fill cap.
2. Add oil slowly.
3. Reinstall the engine oil fill cap, and tighten it securely.
4. Wait for three minutes and recheck the engine oil dipstick.

NOTICE

• Do not fill the engine oil above the upper mark. Overfilling the engine oil may result in leaks and engine damage.
• If any oil spills, wipe it away immediately. Spilled oil may damage the engine compartment components.

Changing the Engine Oil and Oil Filter

• You must change the engine oil and oil filter regularly in order to maintain the engine’s lubrication. The engine may be damaged if they are not changed regularly.
• Turning the power system on automatically starts the engine if the High Voltage battery charge level gauge shows two segments or less.
• Change the oil and filter in accordance with the maintenance message on the driver information interface.

1. Run the engine until it reaches normal operating temperature, and then turn the engine off.
2. Open the hood and remove the engine oil fill cap.
3. Remove the Phillips-head screws and slotted head screws by turning 90°counterclockwise on the undercarriage and remove the under cover.
4. Remove the drain bolt and washer from the bottom of the engine, and drain the oil into a suitable container.
   NOTICE
   You may damage the environment if you do not dispose of the oil in a suitable way. If you are changing the oil by yourself, appropriately dispose of the used oil. Put the oil in a sealed container and take it to a recycling center. Do not throw the oil away into a garbage can or onto the ground.
5. Remove the oil filter and dispose of the remaining oil.
6. Check that the filter gasket is not stuck to the engine contact surface.
   • If it is stuck, you must detach it.
7. Wipe away dirt and dust adhering to the contact surface of the engine block, and install a new oil filter.
   • Apply a light coat of new engine oil to the filter gasket.
8. Put a new washer on the drain bolt, then reinstall the drain bolt.
   • Tightening torque:
   • 30 lbf∙ ft (40 N∙ m, 4.0 kgf ∙m)
9. Pour the recommended engine oil into the engine.
   • Engine oil change capacity (including filter):
   • 3.5 US qt (3.3 L)
10. Reinstall the engine oil fill cap securely and start the engine.
11. Run the engine for a few minutes, and then check that there is no leak from the drain bolt or oil filter.
12.  Stop the engine, wait for three minutes, and then check the oil level on the dipstick.
    • If necessary, add more engine oil.

Changing the Engine Oil and Oil Filter

• You will need a special wrench to replace the oil filter. You can buy this wrench from a dealer.
• When installing the new oil filter, follow the instructions supplied with the oil filter.
• Reinstall the engine oil fill cap. Start the engine. The low oil pressure indicator should go off within five seconds. If it does not, turn off the engine, and check your work.

FAQs

Useful Links

View full PDF: 2022 Honda Insight |Auto User Guide