Honda HR-V 2019 Auto High-Beam User Manual
Introduction
The Honda HR-V’s Auto High-Beam function is an amazing invention that enhances vision while driving at night. It works by strategically positioning a number of cutting-edge sensors and cameras on the car, which are continually scanning the road ahead for approaching traffic and changing lighting conditions.
The technology automatically switches from high-beam to low-beam mode when it detects approaching vehicles or well-lit locations, reducing glare and ensuring that other drivers are not adversely affected by excessive brightness. This clever functionality guarantees a safe and enjoyable driving experience for you and other road users, lowering the chance of accidents and improving all-around road safety. The Honda HR-V 2019 Auto High-Beam sets a new standard for nighttime driving, ensuring a well-lit journey for you and a courteous one for others.
How to Turn Off the Auto High-Beam
Using a camera mounted to the inside of the windshield, this system detects light sources ahead of the vehicle. Depending on the light source, the system automatically switches the headlights to high beam for optimal visibility at night.
The system operates when:
- The headlight switch is in AUTO.
The lever is in the low beam position.
The low beams are on and the system recognizes that you are driving at night.
The vehicle speed is above 45 mph (72 km/h).
How it works
When the camera detects lights coming from a preceding or oncoming vehicle, the headlights remain in low beam.
When the camera detects no lights coming from a preceding or oncoming vehicle, the headlights change to high beam.
The view angle or distance that the camera can detect lights ahead differs depending on conditions, such as the brightness of the lights and the weather.
The auto high-beam determines when to change the headlight beams by responding to the brightness of the lights ahead of your vehicle. In the following cases, the system may not respond to the lights properly:
- The brightness of the lights from the preceding or oncoming vehicle is intense or poor.
Visibility is poor due to the weather (rain, snow, fog, windshield frost, etc.).
Other light sources, such as streetlights and electric billboards are illuminating the road ahead.
The brightness level of the road ahead constantly changes.
The road is bumpy or with many curves.
A vehicle cuts in front of you, or a vehicle in front of you is not in the preceding or oncoming direction. - Your vehicle is tilted with a heavy load in the rear.
If you find the timing of beam changes inconvenient for driving, change the headlight beams manually.
If you do not want the system to be activated at any time when the headlight switch is in AUTO, consult a dealer or disable the system.
Operating the System
To activate the system, turn the headlight switch to AUTO and then set the headlights to low beam. The auto high-beam indicator will come on.
The high beams remain on unless:
- You have been driving below 30 mph (48 km/h) for an extended amount of time.
The windshield wipers have been running at a high speed for more than a few seconds.
You enter a well lit location.
The high beams come back on once the condition that caused them to turn off no longer exists.
If needed, you can temporarily turn the system off manually. Turn on the high beams by pushing the lever forward until you hear a click, or flash the high beams once by pulling the lever toward you. To turn the system back on, pull and hold the lever toward you for a few seconds.
For the auto high-beam to work properly:
- Do not place an object that reflects light on the dashboard.
Keep the windshield around the camera clean.
Do not attach an object or film to the area around the camera.
If the camera receives a strong impact, or repairing of the area near the camera is required, consult a dealer.
If the Some Driver Assist Systems Cannot Operate: Camera Temperature Too High message appears:
- Use the climate control system to cool down the interior and, if necessary, also use defroster mode with the air flow directed toward the camera.
Start driving the vehicle to lower the windshield temperature, which cools down the area around the camera.
If the Auto High-Beam Cannot Operate: Clean Windshield message appears:
- Park your vehicle in a safe place, and clean the windshield. If the message does not disappear after you have cleaned the windshield and driven for a while, have your vehicle checked by a dealer.
Disabling or Re-enabling the System
Disable or re-enable the system when the vehicle is parked and the ignition switch is in ON (w*1 and the light switch is in the AUTO position.
Disabling the system: Pull the light switch lever toward you and hold it for at least 40 seconds. The auto high-beam indicator in the meter will blink twice.
Re-enabling the system: Pull the light switch lever toward you and hold it for at least 30 seconds. The auto high-beam indicator in the meter will blink once.
The auto high-beam is in the previously selected disabled or re-enabled setting each time you start the engine.
Daytime Running Lights
The headlights come on slightly dimmer than normal when the following conditions have been met:
- The ignition switch is in ON
.
U.S. models
- The headlight switch is off, or in
Canadian models
- The headlight switch is AUTO, or in
All models
The parking brake is released
The lights remain on even if you set the parking brake. Turning off the ignition switch or setting the power mode to VEHICLE OFF will turn off the daytime running lights.
The daytime running lights are off once the headlight switch is turned on, or when the head light switch is in AUTO* and it is getting darker outside.
The daytime running lights come on dimmer when the headlight switch is in than when it is in AUTO*. In AUTO*, if the ambient brightness is dark, the low beam headlights come on.
Wipers and Washers
Windshield Wiper/Washer
The windshield wipers and washers can be used when the ignition switch is in ON
MIST
The wipers run at high speed until you release the lever.
Wiper switch (OFF, INT*2/AUTO*3, LO, HI)
Change the wiper switch setting according to the amount of rain.
Adjusting wiper operation
Turn the adjustment ring to adjust the wiper delay.
Lower speed, fewer sweeps
Higher speed, more sweeps
Washer
Sprays while you pull the lever toward you. When you release the lever for more than one second, the spray stops, the wipers sweep two or three more times to clear the windshield, then stop.
- Models with the keyless access system have an ENGINE START/STOP button instead of an ignition switch.
- Models with manual intermittent operation
- Models with automatic intermittent operation
NOTICE
Do not use the wipers when the windshield is dry. The windshield will get scratched, or the rubber blades will get damaged.
NOTICE
In cold weather, the blades may freeze to the windshield.
Operating the wipers in this condition may damage the wipers. Use the defroster to warm the windshield, then turn the wipers on.
Models with intermittent time adjustment ring
If the vehicle speeds up while the wipers are operating intermittently, the length of the wipe interval shortens.
When the vehicle speeds up, the wiper operation’s shortest delay setting ( ) and the LO setting become the same.
All models
Turn the washers off if no washer fluid comes out. The pump may get damaged.
Automatic Intermittent Wipers
When you push the lever down to AUTO, the windshield wipers sweep once, and go into the automatic mode.
The wipers operate intermittently, at low speed, or at high speed and stops in accordance with the amount of rainfall the rainfall sensor detects.
Auto sensitivity adjustment
When in AUTO, you can also adjust the rainfall sensor sensitivity using the adjustment ring.
Sensor sensitivity
Low sensitivity
High sensitivity
If the wiper stops operating due to any obstacle such as the build-up of snow, park the vehicle in a safe place. Rotate the wiper switch to OFF, and turn the ignition switch to ACCESSORY (q or LOCK (0*1, then remove the obstacle.
The wiper motor may stop motor operation temporarily to prevent an overload.
Wiper operation will return to normal within a few minutes, once the circuit has returned to normal.
The rainfall sensor is in the location shown below.
NOTICE
AUTO should always be turned OFF before the following situations in order to prevent severe damage to the wiper system:
- Cleaning the windshield
Driving through a car wash
No rain present
Rear Wiper/Washer
- ON
- INT: Intermittent OFF
- Washer
The rear wiper and washer can be used when the ignition switch is in ON
Wiper switch (OFF, INT, ON)
Change the wiper switch setting according to the amount of rain.
Washer
Sprays while you rotate the switch to this position.
Hold it to activate the wiper and to spray the washer. Once released, it stops operating after a few more sweeps.
Operating in reverse
When you shift the transmission to (R with the windshield wiper activated, the rear wiper operates automatically as follows even if its switch is off.
| Front Wiper Position | Rear Wiper Operation |
| INT* (Intermittent)
AUTO* (Intermittent) |
Intermittent |
| LO (Low speed wipe)
HI (High speed wipe) |
Continuous |
FAQs
What is the Honda HR-V 2019 Auto High-Beam feature?
According to detected road conditions and approaching traffic, the Honda HR-V 2019 Auto High-Beam feature automatically switches the vehicle’s headlights between high-beam and low-beam mode.
To monitor the road and identify other vehicles or ambient lighting conditions, the system uses sensors and cameras. It automatically changes from high to low beam when it notices approaching traffic or well-lit areas.
Using the headlight control stalk on the steering column, you can manually override the system and switch between high-beam and low-beam headlights.
No, the Auto High-Beam feature is intended to function in low-light situations, such as at night or in dimly lit areas.
Using the vehicle’s settings or preferences, you can permanently turn off the Auto High-Beam option.
Depending on the Honda HR-V 2019’s particular trim and option set, the Auto High-Beam feature may or may not be available. Usually, higher trim levels are offered.
It might not be able to retrofit the Auto High-Beam function to previous HR-V models because it needs specialized hardware and electrical system integration.
The Auto High-Beam feature is intended to be effective and only activates when necessary, so power consumption shouldn’t be greatly increased.
It is advised to have an authorized Honda service center check out and fix any issues with the Auto High-Beam feature.
No, using the Auto High-Beam feature in foggy circumstances is not advised because it might result in glare and reduce visibility.
Yes, the system is built to recognize different illumination conditions, including streetlights, and to change the headlights accordingly.
The Auto High-Beam feature’s sensitivity is normally pre-set by Honda and cannot be changed manually.
The Auto High-Beam feature may not work as well on winding or curving roads because it is primarily intended for usage on straight roads.
The Auto High-Beam feature does not conflict with the fog lights and acts independently of them.
While the Auto High-Beam feature is intended to work in a variety of weather conditions, its performance may be diminished by extreme weather such heavy rain or snow.
Reference Links
View Full User Guide: Honda HR-V 2019 Honda
Download Link: https://mygarage.honda.com/s/find-honda