Hyundai Nexo 2020

The Hyundai Nexo 2020 is a state-of-the-art fuel cell vehicle (FCV) that runs on hydrogen. It shows how committed Hyundai is to green and sustainable transportation. As a car that doesn’t put out any pollution, the Nexo is an innovative alternative to standard gasoline-powered cars. It uses hydrogen to make electricity and move forward. The outside of the Nexo has a modern and aerodynamic look to it. It has smooth lines, a bold front grille, and LED lights that make it look modern and energetic. The Nexo’s design is not only nice to look at, but it also helps it work better as a whole. Inside the Nexo, there is a large, cosy cabin that can fit up to five people. The inside is made of high-quality materials and has a lot of facilities and new technology. It has a touchscreen infotainment system that works with smartphones, Bluetooth, navigation, and extra features like a luxury audio system, leather seats, and a panoramic sunroof that can be added as options. The Nexo is a sophisticated and comfortable car to drive.

The fuel cell engine is at the heart of the Nexo. It turns hydrogen into electricity to power the electric motor. This process has no harmful pollutants because it only makes water vapour as a byproduct. The Nexo has a long range and is easy to fill up, which makes it a good choice for long-distance driving.
In terms of safety, the Nexo has improved safety features and technologies that help the driver. Some of these are forward collision warning, automatic emergency braking, blind-spot monitoring, lane-keeping assist, adaptive cruise control, and a camera system that lets you see everything around the car. Hyundai puts safety first in the Nexo so that the driver and other people in the car can feel at ease.
The Hyundai Nexo 2020 is a quiet and smooth car to drive. It accelerates quickly, handles well, and is easy to ride in. The Nexo’s fuel cell technology makes it easy on the environment and keeps it running well.
Overall, the Hyundai Nexo 2020 is a forward-looking and highly advanced car that shows how committed Hyundai is to making transportation more environmentally friendly. It has a modern look, high-tech features, and zero emissions, which makes it a great choice for drivers who care about the environment.

Programming HomeLink®

Please note the following:

• When programming a garage door opener, it is advised to park the vehicle outside of the garage.
• It is recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink® for quicker training and accurate transmission of the radio-frequency signal.
• Some vehicles may require the POWER button to be placed in the ACC (or “Accessories”) position for programming and/or operation of HomeLink®.
• In the event that there are still programming difficulties or questions after following the programming steps listed below, contact HomeLink® at: www.homelink.com or by calling 1-800-355-3515.

Rolling code programming
Rolling code devices that are “code-protected” and manufactured after 1996 may be determined by the following:

• Reference the device owner’s manual for verification.
• The handheld transmitter appears to program the HomeLink® Universal Transceiver but does not activate the device.
• Press and hold the trained HomeLink button. The device has the rolling code feature if the indicator light flashes rapidly and then turns solid after 2 seconds.

To train rolling code devices, follow these instructions:

1. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. The exact location and color of the button may vary by garage door opener brand. If there is difficulty locating the training button, reference the device owner’s manual or please visit our Web site at www.homelink.com.
2. Firmly press and release the “learn” or “smart” button (which activates the “training light”). You will have 30 seconds to initiate step 3.
3. Return to the vehicle and firmly press, hold for two seconds, and then release the desired HomeLink® button. Repeat the “press/hold/release” sequence a second time to complete the programming. (Some devices may require you to repeat this sequence a third time to complete the programming.)
4. Press and hold the just-trained HomeLink® button and observe the red Status Indicator LED. If the indicator light stays on constantly, programming is complete and your device should activate.
5. To program the remaining two HomeLink® buttons, follow either steps 1 through 4 above for other Rolling Code devices or steps 2 through 5 in Standard Programming for standard devices. Standard programming

To train most devices, follow these instructions:

1. For first-time programming, press and hold the two outside buttons, HomeLink® Channel 1 and Channel 3 Buttons, until the indicator light begins to flash (after 20 seconds). Release both buttons. Do not hold the buttons for longer than 30 seconds.
2. Position the end of your hand-held transmitter 1-3 inches (2-8 cm) away from the HomeLink® buttons while keeping the indicator light in view.
3. Simultaneously press and hold both the HomeLink® and hand-held transmitter buttons. DO NOT release the buttons until step 4 has been completed.
4. While continuing to hold the buttons the red Indicator Status LED will flash slowly and then rapidly after HomeLink® successfully trains to the frequency signal from the hand-held transmitter. Release both buttons
5. Press and hold the just-trained HomeLink® button and observe the red Status Indicator LED. If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink® button is pressed and released.
6. To program the remaining two HomeLink® buttons, follow steps 2 through 5.

Gate operator & Canadian programming
During programming, your handheld transmitter may automatically stop transmitting. Continue to press the Integrated HomeLink® Wireless Control System button (note steps 2 through 4 in the Standard Programming portion of this document) while you press and re-press (“cycle”) your handheld transmitter every two seconds until the frequency signal has been learned. The indicator light will flash slowly and then rapidly after several seconds upon successful training.

Operating HomeLink®
To operate, simply press and release the programmed HomeLink® button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.). For convenience, the hand-held transmitter of the device may also be used at any time.

Reprogramming a single HomeLink® button
To program a new device to a previously trained HomeLink® button, follow these steps:

1. Press and hold the desired HomeLink® button. Do NOT release until step 4 has been completed.
2. When the indicator light begins to flash slowly (after 20 seconds), position the handheld transmitter 1 to 3 inches away from the HomeLink® surface.
3. Press and hold the handheld transmitter button. The HomeLink® indicator light will flash, first slowly and then rapidly.
4. When the indicator light begins to flash rapidly, release both buttons.
5. Press and hold the just-trained HomeLink® button and observe the red Status Indicator LED. If the indicator light stays on constantly, programming is complete and your new device should activate.

Erasing HomeLink® buttons
Individual buttons cannot be erased. However, to erase all three program buttons:

1. Press and hold the two outer HomeLink® buttons until the indicator light begins to flash after 20 seconds.
2. Release both buttons. Do not hold for longer than 30 seconds.
   The Integrated HomeLink® Wireless Control System is now in the training (learn) mode and can be programmed at any time following the appropriate steps in the Programming chapters above. NVS® is a registered trademark and Z-Nav™ is a trademark of the Gentex Corporation, Zeeland, Michigan. HomeLink® is a registered trademark owned by Johnson Controls, Incorporated, Milwaukee, Wisconsin.

FCC ID: NZLHFCHL4
IC: 4112A-HFCHL4

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following three conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
3. The transceiver has been tested and complies with FCC and Industry Canada rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device.

FOR CANADA
This device complies with Industry Canada Standard RSS-210.
Operation is subject to the following three conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
3. The transceiver has been tested and complies with FCC and Industry Canada rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device.

2023 Hyundai Nexo Specs, Price, Features, Mileage (Brochure)

Reference Link

Download Link: https://owners.hyundaiusa.com/us/en/resources/manuals-warranties.html