2024 Indian Motorcycle Challenger User Manual
The Indian Motorcycle Challenger of 2024 is a powerful two-wheeled representation of power and accuracy. Easily conquer the open road with this touring motorcycle’s powerful presence and bold appearance. Equipped with a sturdy V-twin engine, the Challenger offers both thrilling performance and comfortable long-distance travel. This bike redefines traveling with its cutting-edge technology, which includes rider-assist functions and superior infotainment. The 2024 Indian Motorcycle Challenger promises an unrivaled blend of style, performance, and touring potential, setting a new standard in the world of American touring bikes, whether you’re going on a cross-country trip or just enjoying the thrill of the ride.
TOGGLE SWITCHES
All models are equipped with toggle switches on the front side of the left q and right handlebar controls.
The power switch must be ON for the toggle switches to function. Use the right-hand switch to navigate through menus or accept dialog boxes on the Ride Command display. Use the left-hand switch to back out of menus, decline dialog boxes, hang up phone calls, and toggle through display screens.
SWITCHES
POWER SWITCH
The power switch is located on the right control q. Press and release the power switch to enable or disable all electrical power to the vehicle.
To disable all electrical power if the motorcycle is moving and the engine is running, press and hold the power switch for more than three seconds. This will also turn the engine off.
NOTICE
The headlights and any accessories plugged into power ports will remain on until the power switch is turned off. To save battery power, the vehicle will automatically power off after five minutes of inactivity. Automatic power down can be overridden on bikes equipped with an INDIAN MOTORCYCLE Ride Command display through the Vehicle Settings menu.
ENGINE STOP/RUN SWITCH
Use the engine stop/run switch to turn the engine off quickly. Press the top of the switch (STOP) q to interrupt the circuits and stop the engine. The engine should not start or run when the switch is in the STOP position. Press the bottom of the switch (RUN) w to complete the circuits and allow the engine to start and run. Press and Release the
bottom switch (RUN) w to start the engine.
CRUISE CONTROL SWITCH
Cruise control can be activated and adjusted from the right control using the Cruise Control Switch q. For more information about Cruise Control.
WINDSHIELD SWITCH
Use the windshield switch q to adjust windshield height for the best wind deflection. Press up on the switch to adjust the windshield upward. Press down on the switch to adjust the windshield downward. Double tap up or down on the switch to auto-adjust the windshield all the way up or down. If the windshield is traveling and the opposite direction is briefly pressed, the auto travel is canceled.
HIGH/LOW HEADLIGHT BEAM SWITCH
The headlights automatically come on when the engine is started. The high/low headlight beam switch toggles the headlight between high beam and low beam. To activate the high beam, press the upper portion of the switch. To activate the low beam, press the lower portion of the switch. To momentarily flash headlights (Flash to Pass), press and hold the lower portion of the switch.
HORN SWITCH
Press the horn switch q to sound the horn.
HAZARD SWITCH
The power switch must be ON to activate the flashers, but once activated, the flashers will continue to flash when the power switch is turned off. When the flashers are active, all four turn signals flash.
To activate the hazard switch, press on the center of the turn signal switch q.
- Press and hold the switch to activate the flashers.
- Press the switch again to cancel the flashers.
TURN SIGNAL
Move the switch q to the left to activate the left turn signals. Move the switch q to the right to activate the right turn signals. A signal will deactivate automatically when speed or distance reach predetermined levels. To cancel a signal manually, move the switch to the center position and push it inward. Momentary Feature: Move the turn signal switch left or right and hold it in that position for at least one second. The momentary feature will activate and the signal will then cancel when the switch is released. One arrow flashes when the corresponding turn signal is activated. Both arrows flash when the hazard signal is activated. If there is a problem in the signal system, the lamps will flash at twice the normal rate.
AUDIO CONTROL SWITCH (IF EQUIPPED)
The Audio Control Switch q allows users to control the audio system features from the left control block.
VOLUME
To increase volume, press up on the audio control switch. To decrease the volume, press down on the audio control switch. To mute the volume, push in on the audio control switch.
NOTICE
When using a Bluetooth® audio device, pushing down on the audio control switch will pause the audio. To resume, press down on the audio control switch again.
TUNER
When the audio source is set to Tuner, press left or right to navigate through preset stations. Press and hold to seek.
PERSONAL AUDIO
When audio source is set to Bluetooth® Audio or USB, press left or right to navigate through audio tracks.
AUXILIARY LIGHT SWITCH (IF EQUIPPED)
The auxiliary lights provide additional lighting on each side of the headlight. Some drivers prefer using the auxiliary lights when operating in foggy conditions or when passing a vehicle to help improve visibility to other motorists. Press the auxiliary light switch or use the Ride Command Control Panel to turn the auxiliary lights on or off. The switch background light changes color to indicate whether lights are on or off.
- OFF: Black Light
- ON: Green Light
A green icon will show along the top bar when the auxiliary lights are on. The auxiliary lights turn off when the power switch is turned off. The auxiliary lights automatically turn on when the engine starts if they were on when the engine was shut down. To control when the fog light is enabled / disabled, use the fog light settings page.
KEYLESS IGNITION
WARNING
Keep the key fob and key fob battery out of reach of children. Swallowing can lead to chemical burns, perforation of soft tissue, and death. Severe burns can occur within 2 hours of ingestion. Seek medical attention immediately.
STARTING KEY FOB OPERATION:
When the electrical system is activated with the power switch, the key fob must be within range. If the key fob is not detected, the security light will flash. The electrical system will automatically shut down.
The starter motor will not engage during this time. If a key fob is not available, your personal identification number (PIN) can be entered using the turn signal switches, or on the Ride Command display screen (if equipped), to unlock the security system.
DRIVING KEY FOB OPERATION:
After starting the engine, the Vehicle Control Module (VCM) will verify that the key fob is within range again when shifting from neutral into gear. The security light may turn on during this check. The VCM will not search for the key fob again after the vehicle has moved. If the key fob is lost during riding, the PIN will be needed to restart the vehicle.
If the key fob is not detected when shifting into gear:
- The horn will sound and the security light will flash.
- The engine will then turn off.
- The electrical system will then automatically shut down.
KEY FOB STORAGE:
The key fob should not be stored in the phone storage compartment, or near devices that can interfere with radio waves, such as cell phones, power supplies, or magnets, during operation.
SADDLEBAG LOCK SWITCH (IF EQUIPPED)
Use the key fob or the lock switch on the console to lock and unlock the electric saddlebag locks. When using the console lock switch, the key fob must be within range. If the key fob is not detected, the security light and/or power switch will flash. The system will not perform the lock or unlock command.
HEATED SEAT SWITCHES (IIFF EQUIPPED)
Use the seat switches located on the lower left edge of the seat to
adjust heating settings. The front switch q controls the settings for the driver seat, and the rear switch (if equipped) w controls the passenger seat setting. The heated seat will only operate if the engine is on. For models equipped with Ride Command, a brief pop-up will appear on the touchscreen display when the heat level is changed.
SPEEDOMETER
The speedometer displays forward vehicle speed in either miles per hour or kilometers per hour.
TACHOMETER
The tachometer displays engine speed in revolutions per minute (RPM). A red line on the face of the gauge indicates the maximum safe engine speed. Excessive engine speed can cause engine damage or failure, which could result in serious injury or death. Do not allow engine speed to exceed the red line.
FUEL GAUGE DISPLAY
The fuel gauge displays the fuel level. For the most accurate reading, sit on the motorcycle and bring it to the upright position. The segments of the fuel gauge show the level of fuel in the fuel tank. When the last segment clears, a low fuel warning is activated. All segments including the fuel icon will flash. Refuel promptly.
REAR CYLINDER DEACTIVATION
Designed as an aid to reduce engine and exhaust heat to the rider, Rear Cylinder Deactivation turns off the rear cylinder when the engine gets hot. The following conditions must be met for Rear Cylinder Deactivation to be enabled.
- The engine must be up to operating temperature
- Ambient Temperature must exceed 59 °F (15 °C)
- Engine speed must remain below 1000 rpm
- The throttle must be in the closed position (0% throttle)
- Exhaust catalyst temperature must be sufficiently high for tailpipe emissions compliance.
NOTICE
If the catalyst temperature drops below the emissions threshold the rear cylinder will re-engage until the catalyst temperature rises above the threshold at which point the rear will deactivate again.
Cylinder Deactivation can be turned off by accessing the settings menu in the drop-down from the top of the screen. Cylinder Deactivation controls are in the Vehicle menu. When Rear Cylinder Deactivation is functioning, an icon will illuminate at the top of the Ride Command display screen.
FAQs
The 2024 Indian Motorcycle Challenger is a touring motorcycle designed for long-distance journeys with a blend of power and comfort.
The Challenger is distinguished by its touring-focused design, advanced technology, and powerful engine.
It features a robust V-twin engine known for its power and smooth performance.
Exact figures may vary by model, but it typically produces around 120-130 horsepower and ample torque for touring.
Yes, it’s specifically designed for comfortable and extended rides, making it an ideal choice for touring enthusiasts.
The Challenger is aimed at riders who value touring comfort, advanced technology, and powerful performance.
Indian Motorcycle offers a range of touring accessories, and there’s a growing aftermarket community for customization.
Indian Motorcycle typically offers various classic and contemporary colors, though availability may vary by region.
It typically features a comfortable two-up seat with ample passenger accommodations.
Yes, it often includes modern features such as advanced infotainment systems, rider-assist features, and connectivity options.
Despite its size, the Challenger is designed for excellent stability and control, even during long rides.
Specific mileage may vary, but the Challenger typically offers reasonable fuel efficiency for a touring motorcycle.
Yes, Indian Motorcycle typically provides warranty coverage for their motorcycles, but details may differ by region.
While it’s suitable for riders of all experience levels, it’s often favored by riders with touring experience.
The 2024 Dodge Challenger has a starting price of AED 129,900 and can go up to AED 409,900 in Dubai. In the Philippines, the 2024 Dodge Challenger starts at P5,150,000.
Useful Link
Download Manuals: https://www.indianmotorcycle.com/en-us/owners-manuals/