Jayco Eagle Fifth Wheels 2023 Linc Remote Control User Manual
Linc Remote Control
Configuring the remote to sync with the OneControl Touch panel:
- Press the chrome button on the bottom of the remote to turn it on. Enter the PIN (default is 0,0,0,0). The PIN can be changed after entering the default PIN. A menu will appear, choose Leveler from that menu.
- Turn the OneControl Touch Panel ON inside the RV.
- At the top of the Touch Panel screen press the “CONNECTED” icon quickly (6) times.
- A GEAR icon will appear at the top of the screen that says “OPTIONS”. Press the GEAR icon.
- Screen display changes to “Select Operation” with arrows on the left side of the screen. Use to arrows on left side of screen. Scroll to “WIRELESS CONFIG”.
- Press the ENTER button at the bottom of the screen.
- The screen will display “Wireless Configuration Press any Linc button to sync”.
- Press any button on the remote control while in Leveler mode and the remote will be connected.
Pressing the ABORT button on the touch screen will cancel the configuration sequence.
The following functions can be operated using the Linc Remote Control. Refer to the manufacturer’s manual for complete instructions.
- Basic Jack operation
- Unhitching Instructions
- Auto Leveling
Troubleshooting
Refer to the manufacturer’s manual for troubleshooting information which includes the following:
- OneControl Touch Panel Error Codes
- Special Jack Error Codes on the OneControl Touch Panel
- How to manually override the jack motor
- Setting Zero Point Calibration
- Zero point is the programmed point that the RV will return to each time the Auto Level feature is used. Zero Point is only available on the OneControl Touch Panel.
- Preventative Maintenance tips
Stabilizer Jacks
Warning
- DO NOT USE THE STABILIZER JACKS TO LEVEL THE RV. It is important to remember that the stabilizer jacks are to be used only for support while occupying and moving around the RV. They are not designed to support the weight of the RV.
- The stabilizer jacks must be fully retracted before moving or towing the RV to prevent stabilizer jack damage.
Each stabilizer jack can be individually adjusted to stabilize the RV for use. When setting up on the soft ground, you may wish to place a wood pad or the equivalent under each stabilizer jack foot to help keep the jack from sinking into the ground.
Manual Stabilizer Jacks (if so equipped)
- To lower each jack, insert the jack crank onto the applicable stabilizer jackshaft.
- Turn the crank clockwise to lower each leg until it contacts the ground and stabilizes the RV.
To raise each jack, insert the jack crank onto the applicable stabilizer jack shaft and turn the crank counter-clockwise.
Electric Stabilizer Jacks (if so equipped)
Control switches for the stabilizer jacks are typically located on the (door) side of the unit above the stabilizer jack(s). To lower each jack, press the control switch until each leg contacts the ground and stabilizes the unit. To raise the jack, press the control switch until the jack is returned to the retracted position.
Manual Override
The electric stabilizer jacks may have a built-in manual override system. The override coupler is located on the end of the stabilizer jack opposite the electric motor. One of the wire motor leads must be disconnected to prevent backloading the motor and causing more damage. Disconnect the battery from the system prior to manual operation. Insert the 1/2” diameter crank handle inside the coupler. The slot in the end of the crank handle accommodates the pin inside the coupler to allow manual extension/retraction of the stabilizer jack. Rotate the handle clockwise to retract and counter clockwise to extend the jack.
NOTE:
The gears can be stripped out if the stab jack is manually retracted/ extended to its fullest extent and the operator continues to rotate the manual override.
The following functions can be operated using the Linc Remote Control. Refer to the manufacturer’s manual for complete instructions. One of the wire motor leads must be disconnected to prevent backloading the motor and causing more damage. Disconnect the battery from the system prior to manual operation. Insert the 1/2” diameter crank handle inside the coupler. The slot in the end of the crank handle accommodates the pin inside the coupler to allow manual extension/retraction of the stabilizer jack. Rotate the handle clockwise to retract and counter clockwise to extend the jack.
[amalinkspro_table id=”32452″ new-window=”on” nofollow=”on” addtocart=”off” /]
Reference Links
View Full User Guide: Jayco Eagle Fifth Wheels 2023 User Manual
Download Manuals: https://www.jayco.com/manuals/