2022 Jeep Wrangler Cluster Warning Lights Guide
The cluster warning lights on the 2022 Jeep Wrangler serve as a visual guide to keep you informed about the status of your vehicle and any potential concerns that may develop throughout your journey. These lights provide a complete system to guarantee you’re informed of everything going on with your Wrangler, from crucial indicators to alarms for potential problems. Understanding these warning lights not only promotes safe driving but also aids in the maintenance of your vehicle’s performance.
WARNING LIGHTS AND MESSAGES
The warning/indicator lights will illuminate the instrument panel together with a dedicated message and/or acoustic signal when applicable. These indications are indicative and precautionary and as such must not be considered as exhaustive and/or alternative to the information contained in the Owner’s Manual, which you are advised to read carefully in all cases. Always refer to the information in this chapter in the event of a failure indication. All active telltales will display first if applicable. The system check menu may appear differently based on equipment options and current vehicle status. Some telltales are optional and may not appear.
RED WARNING LIGHTS
Air Bag Warning Light
This warning light will illuminate to indicate a fault with the airbag and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ ON/RUN position. This light will illuminate with a single chime when a fault with the airbag has been detected, it will stay on until the fault is cleared. If the light is not on during startup, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.
Brake Warning Light
This warning light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capacity in the event of a failure of a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.
The light will remain on until the cause is corrected.
NOTE:
The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is necessary.
WARNING!
Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately.
Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.
NOTE:
This light shows only that the parking brake is applied. It does not show the degree of brake application.
Battery Charge Warning Light
This warning light will illuminate when the battery is not charging properly. If it stays on while the engine is running, there may be a malfunction with the charging system. Contact an authorized dealer as soon as possible. This indicates a possible problem with the electrical system or a related component.
Door Open Warning Light
This indicator will illuminate when a door is ajar/open and not fully closed.
NOTE:
If the vehicle is moving, there will also be a single chime.
Electric Power Steering (EPS) Fault Warning Light
This warning light will turn on when there’s a fault with the EPS system
WARNING!
Continued operation with reduced assistance could pose a safety risk to yourself and others. Service should be obtained as soon as possible.
Electronic Throttle Control (ETC) Warning Light
This warning light will illuminate to indicate a problem with the ETC system. If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem. Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK (P) position. The light should turn off. If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.
NOTE:
This light may turn on if the accelerator and brake pedals are pressed at the same time. If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall, and your vehicle may require towing. The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer.
Engine Coolant Temperature Warning Light
This warning light warns of an overheated engine condition. If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound. If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool, whichever comes first. If the light turns on while driving, safely pull over and stop the vehicle. If the Air Conditioning (A/C) system is on, turn it off. Also, shift the transmission into NEUTRAL (N) and idle the vehicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service
Hood Open Warning Light
This indicator will illuminate when the hood is ajar/open and not fully closed.
NOTE:
If the vehicle is moving, there will also be a single chime.
Oil Pressure Warning Light
This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure. If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible. After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light. If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance. Do not operate the vehicle until the cause is corrected. If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible. Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine. The engine oil level must be checked under the hood.
Oil Temperature Warning Light
This warning light will illuminate to indicate the engine oil temperature is high. If the light turns on 
while driving, stop the vehicle and shut off the engine as soon as possible. Wait for the oil temperature to return to normal levels.
Seat Belt Reminder Warning Light
This warning light indicates when the driver or passenger seat belt is unbuckled. When the ignition is first placed in the ON/RUN or ACC/ON/RUN position and if the driver’s belt is unbuckled, a chime will sound and the light will turn on. When driving, if the driver or front passenger seat belt remains unbuckled, the Seat Belt Reminder Light will flash or remain on continuously and a chime will sound.
Swing Gate Open Warning Light
This warning light will illuminate when the swing gate is open.
NOTE:
If the vehicle is moving, there will also be a single chime.
Transmission Temperature Warning Light
This warning light will illuminate to warn of a high transmission fluid temperature. This may occur with strenuous usage such as trailer towing. If this light turns on, stop the vehicle and run the engine at idle or slightly faster, with the transmission in PARK (P) or NEUTRAL (N), until the light turns off. Once the light turns off, you may continue to drive normally.
WARNING!
If you continue operating the vehicle when the Trans-mission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components, and cause a fire. If you continue to operate the vehicle when the “CLUTCH HOT” message is displayed, or the Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.
CAUTION!
Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure. If you continue to operate the vehicle when the
“CLUTCH HOT” message is displayed, or the Transmission Temperate Warning Light is illuminated, you could cause the clutch to overheat and cause severe clutch damage, transmission damage, or failure.
Vehicle Security Warning Light —If Equipped
This light will flash at a fast rate for approximately 15 seconds when the Vehicle Security system is arming and then will flash slowly until the vehicle is disarmed.
YELLOW WARNING LIGHTS
Anti-lock brake System (ABS) Warning Light
This warning light monitors the ABS. The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible. However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on. If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.
Electronic Stability Control (ESC) Active Warning Light — If Equipped
This warning light will indicate when the Electronic Stability Control system is Active. The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated. It should go out with the engine running. If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system. If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.
- The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN or ACC/ON/RUN position.
- The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive.
- This light will come on when the vehicle is in an ESC event.
Electronic Stability Control (ESC) OFF Warning Light — If Equipped
This warning light indicates the ESC is off. Each time the ignition is turned to ON/RUN or ACC/ON/RUN, the ESC system will be on, even if it was turned off previously.
Fuel Level Sensor Failure Warning Light
This light illuminates when there is a fuel level sensor failure. If this light illuminates, take it to an authorized dealer and have them inspect it.
Low Fuel Warning Light
When the fuel level reaches approximately 2.0 gal (7.5 L), this light will turn on and a chime will sound. The light will remain on until fuel is added.
Engine Check/Malfunction Indicator Warning Light (MIL)
The MIL is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.
This warning light will illuminate when the ignition is in the ON/RUN position before the engine starts. If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition
checked promptly? Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after the engine starts. The vehicle should be serviced if the light stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not require towing. When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.
WARNING!
A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions. This can cause a fire if
WARNING!
you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants, or others.
CAUTION!
Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system. It also could affect fuel economy and drive-ability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required.
Service 4WD Warning Light 
This warning light will illuminate to signal a fault with the 4WD system. If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required. We recommend you drive to the nearest service center and have the vehicle serviced immediately.
Service Forward Collision Warning (FCW) Light — If Equipped
This warning light will illuminate to indicate a fault in the Forward Collision Warning System. Contact an authorized dealer for service.
Service Stop/Start System Warning Light — If Equipped
This warning light will illuminate when the Stop/Start system is not functioning properly and service is required. Contact an authorized dealer for service.
Cruise Control Fault Warning LightThis warning light will illuminate to indicate the Cruise Control system is not functioning properly and service is required. Contact an authorized dealer.
Sway Bar Fault Warning Light
This light will illuminate when there is a fault in the sway bar disconnect system.
Tire Pressure Monitoring System (TPMS) Warning LightThe warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tire duration and fuel consumption may not be guaranteed. Should one or more tires be in the condition previously mentioned, the display will show the indications corresponding to each tire.
CAUTION!
Do not continue driving with one or more flat tires as handling may be compromised. Stop the vehicle, avoiding sharp braking and steering. If a tire puncture occurs, repair immediately using the dedicated tire repair kit and contact an authorized dealer as soon as possible.
Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires. As an added safety feature, your vehicle has been equipped with a TPMS that illuminates a low tire pressure telltale when one or more of your tires is significantly underinflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Underinflation also reduces fuel efficiency and tire tread life and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if underinflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.
CAUTION!
The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Using aftermarket tire sealants may cause the Tire Pressure Monitoring System (TPMS) sensor to become inoperable. After using an aftermarket tire sealant it is recommended that you take your vehicle to an authorized dealer to have your sensor function checked.
YELLOW INDICATOR LIGHTS
4WD Indicator Light — If Equipped
This light alerts the driver that the vehicle is in the Four-Wheel Drive (4WD) mode, and the front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.
4WD Low Indicator Light — If Equipped
This light alerts the driver that the vehicle is in the 4WD Low mode. The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed. Low range provides a greater gear reduction ratio to provide increased torque at the wheels page 154.
4WD Part Time Indicator Light — If Equipped
This light alerts the driver that the vehicle is in the Four-Wheel Drive part-time mode, and the front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.
Axle Locker Fault Indicator Light
This light indicates when the front and/or rear axle locker fault has been detected.
Forward Collision Warning (FCW) OFF Indicator Light — If Equipped
This indicator light illuminates to indicate that the Forward Collision Warning is off
Front And Rear Axle Lock Indicator Light
This light indicates when the front, rear, or both axles have been locked. The telltale will display the lock icon on the front and rear axles to indicate the current lock status.
Neutral Indicator Light — If Equipped
This light alerts the driver that the vehicle is in Neutral mode.
Rear Axle Lock Indicator Light
This light indicates when the rear axle lock has been activated.
Sway Bar Indicator Light — If Equipped
This indicator light will illuminate when the front sway bar is disconnected.
GREEN INDICATOR LIGHTS
Adaptive Cruise Control (ACC) Set With No Target Detected Indicator Light —If Equipped
This light will turn on when the Adaptive Cruise Control is set and there is no vehicle in front detected
Adaptive Cruise Control (ACC) Set With Target Indicator Light
This will display when the ACC is set and a vehicle in front is detected.
Cruise Control SET Indicator Light With A Premium Instrument Cluster
This indicator light will illuminate when the Cruise Control is set to the desired speed.
Front Fog Indicator Light
This indicator light will illuminate when the front fog lights are on.
- Max Regeneration On” – appears when the feature
is turned on. - Max Regeneration Off” – appears when the feature
is turned off. - “Max Regeneration Unavailable” – appears when the feature is requested, but the vehicle is unable to comply. The LED will flash for five seconds to indicate unavailability
Parking/Headlights On Indicator Light
This indicator light will illuminate when the parking lights or headlights are turned on.
Turn Signal Indicator Lights
When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash. Turn signals can be activated when the multifunction lever is moved down (left) or up (right).
NOTE:
- A continuous chime will sound if the vehicle is
driven more than 1 mile (1.6 km) with either turn
signal on. - Check for an inoperative outside light bulb if either
indicator flashes at a rapid rate.
WHITE INDICATOR LIGHTS
Adaptive Cruise Control (ACC) Ready Indicator Light 
This light will turn on when the vehicle equipped with ACC has been turned on, but not set.
2WD High Indicator Light
With a Premium Instrument Cluster, This light alerts the driver that the vehicle is in the Two-Wheel Drive High mode.
Hill Descent Control (HDC) Indicator Light — If Equipped
This indicator shows when the HDC feature is turned on. The light will be on solid when HDC is armed. HDC can only be armed when the transfer case is in the 4WD Low position and the vehicle speed is less than 30 mph (48 km/h). If these conditions are not met while attempting to use the HDC feature, the HDC indicator light will flash on/off.
Selec-Speed Control Indicator Light — If Equipped
This light will turn on when “Selec-Speed Control” is activated. To activate “Selec-Speed Control”, ensure the vehicle is in 4WD Low and push the button on the Instrument Panel.
NOTE:
If the vehicle is not in 4WD Low, “To Enter Selec-Speed Shift to 4WD Low” will appear in the instrument cluster display.
Cruise Control Ready Indicator Light — If Equipped With A Premium Instrument Cluster
This light will turn on when the Cruise Control has been turned on, but not set.
Cruise Control SET Indicator Light — If Equipped With Base Instrument ClusterThis indicator light will illuminate when the Cruise Control is set.
BLUE INDICATOR LIGHTS
High Beam Indicator Light
This indicator light will illuminate to indicate that the high-beam headlights are on. With the low beams activated, push the multifunction lever forward (toward the front of the vehicle) to turn on the high beams. Pull the multifunction lever rearward (toward the rear of the vehicle) to turn off the high beams. If the high beams are off, pull the lever toward you for a temporary high beam on, “flash to pass” scenario.
GRAY INDICATOR LIGHTS
Cruise Control Ready Indicator Light — If Equipped With Base Instrument Cluster
This light will turn on when the Cruise Control has been turned on, but not set.
FAQs
The check engine light indicates a possible problem with the engine or emissions system. It is recommended that you have it checked by a specialist.
The battery light indicates a problem with the charging system. It could indicate a problem with the battery, alternator, or other associated components.
Check the engine oil level shortly after stopping the car. Low oil pressure can cause significant engine damage. Seek professional assistance if the oil level is adequate.
When the tire pressure in one or more tires is substantially low, the TPMS light illuminates. Check tire pressure and inflate to specified levels.
The ABS light shows that there is a problem with the Anti-Lock Braking System. It is safe to drive, but have it checked as soon as possible to guarantee adequate braking performance.
This light indicates that there is an issue with the traction control system. Driving is generally safe, although the system may not function properly, especially in wet circumstances.
The airbag light indicates a possible problem with the airbag system. For safety reasons, have it inspected by a technician as soon as feasible.
When the engine overheats, the coolant temperature light illuminates. Before continuing, pull over, let the engine cool down, and check the coolant level.
The gasoline cap light usually indicates that the fuel cap is not securely secured. To guarantee a proper seal, check and tighten the fuel cap until it clics.
The ESP/BAS light signifies that the Electronic Stability Program or Brake Assist System is malfunctioning. It is safe to drive, but it should be verified by a specialist.
This light simply indicates that the windshield washer fluid reservoir needs to be refilled.
The low tire tread indicator notifies you when one or more tires have worn to the point where they must be replaced. Inspect the tire(s) and replace them as needed.
The glow plug indicator light is unique to diesel-powered Wranglers and indicates that the glow plugs are actively heating prior to starting the engine.
A flashing cruise control light may indicate a system malfunction. Check the owner’s manual or have an expert inspect it.
When the system is activated, the hill descent control light glows, assisting in maintaining a safe speed when driving downhill.
Useful Link
View Full PDF : 2022 Jeep Wrangler Owner’s Manual| Auto User Guide 2022 Jeep Wrangler Alarm System Guide