2024 Jeep Gladiator Keys and Smart Key Guide

2024 Jeep Gladiator Keys and Smart Key Owner’s Manual

Traditional and smart keys are both available on the 2024 Jeep Gladiator. While the smart key provides keyless entry and push-button start for increased convenience and security, the normal key permits manual entry and ignition. The Gladiator offers drivers current functionality and accessibility with these options.

2024 JEEP Wrangler Review, Price, Features And Mileage (Brochure)

Jeep KEYS Guide

KEY FOB
Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter ‘n Go™ (if equipped), and Remote Start (if equipped). The key fob allows you to lock or unlock the doors and tailgate from distances up to approxi-mately 66 ft (20 m). The key fob does not need to be pointed at the vehicle to activate the system. The key fob also contains a mechanical key.

NOTE:

• The key fob’s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device. This may result in poor performance.
• With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.

WARNING!
Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.

CAUTION!
The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks. To ensure the complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.
Key Fob

1. Mechanical Key Release Button
2. LED Indicator
3. Unlock Button
4. Lock Button
5. Remote Start Button (If Equipped)
6. Panic Button

NOTE:

• In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery. A low-key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob. If the LED key fob light no longer illuminates from the key fob button push, then the key fob battery requires replacement.
• Improper disposal of key fob batteries may be harmful to the environment. Please see an authorized dealer for proper battery disposal.

To Lock/Unlock The Doors And Tailgate

Push and release the unlock button on the key fob once to unlock the driver’s door, or twice to unlock all the doors. To lock all the doors, push the lock button once.
When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated. When the doors are locked, the turn signals will flash and the horn will chirp.

NOTE:

• All doors can be programmed to unlock on the first push of the unlock button through Uconnect Set-tings page 166.
• The mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartment (if equipped), and rear seatbacks.

Key Left Vehicle Feature
If a valid key fob is no longer detected inside the vehicle while the vehicle’s ignition system is in the ON/RUN or START position, the message “Key Fob Has Left The Vehicle” will be shown in the instrument cluster display along with an interior chime. An exterior audible and visual alert will also be activated to warn the driver.
The vehicle’s horn will rapidly chirp three times along with a single flash of the vehicle’s exterior lights.

NOTE:

• The doors have to be open and then closed for the vehicle to detect a key fob. The Key Left Vehicle feature will activate when the first door is closed and no key fob is detected in the vehicle. If the warning has been activated, and the other doors are closed, no other warnings will be issued.
• These alerts will not be activated in situations where the vehicle’s engine is left running with the key fob inside, or the key fob’s wireless signals are blocked.

Replacing The Battery In The Key Fob
The recommended replacement battery is CR2450.

NOTE:

• Customers are recommended to use a battery obtained from Mopar®. Aftermarket coin battery dimensions may not meet the original OEM coin battery dimensions.
• Perchlorate material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate for further information.
• Do not touch the battery terminals that are on the back housing or the printed circuit board.
• When a key fob battery is low, a warning will be indicated on the vehicle’s instrument cluster, and the fob LED will no longer illuminate with a button push.

1. Remove the back cover of the key fob by inserting a flat-blade screwdriver into the slot on the bottom of the fob. Apply light pressure until the cover unsnaps being careful not to damage the seal. Proceed counterclockwise (in the order shown in the following image) to loosen the remaining snaps until the bat-tery cover can be removed.
   
   
2. Remove the depleted battery by inserting a small flat-blade screwdriver into the battery removal slot and sliding the battery forward and upward being careful not to damage the electronic board underneath.
   
   
3. Install the new battery into the key fob, making sure the positive (+) side is facing up. Slide the battery until it is seated securely below the tabs.
4. Reassemble the back cover making sure it is properly aligned before snapping it back in place.

WARNING!

• The integrated key fob contains a coin cell battery. Do not ingest the battery; there is a chemical burn hazard. If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.
• If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.
• Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.

Programming And Requesting Additional Key Fobs

Programming the key fob may be performed by an authorized dealer.

NOTE:

• Once a key fob is programmed into a vehicle, it cannot be repurposed and reprogrammed into another vehicle.
• Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.

WARNING!

• Always remove the key fobs from the vehicle and lock all doors when leaving the vehicle unattended.
• For vehicles equipped with Keyless Enter ‘n Go™ Ignition, always remember to place the ignition in the OFF position when exiting the vehicle.

Duplication of key fobs may be performed at an authorized dealer. This procedure consists of programming a blank key fob to the vehicle electronics. A blank key fob has never been programmed.

NOTE:

• When having the Sentry Key Immobilizer system serviced, bring all vehicle keys with you to an authorized dealer.
• Keys must be ordered to the correct key cut to match the vehicle locks.

SENTRY KEY

The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine. The sys-tem does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.
The system uses a key fob, keyless push-button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation. Therefore, only key fobs that are programmed into the vehicle can be used to start and operate the vehicle. The system cannot reprogram a key fob obtained from another vehicle.
After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb checks, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob. If a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.
If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.

CAUTION!
The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics

NOTE:
A key fob that has not been programmed is also considered an invalid key.

IGNITION SWITCH

KEYLESS ENTER ‘N GO™ IGNITION
This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.
The START/STOP ignition button has several operating modes that are labelled and will illuminate when in position. These modes are OFF, ACC, RUN, and START.
START/STOP Ignition Button
The push-button ignition can be placed in the following modes:

OFF

• The engine is stopped.
• Some electrical devices (e.g. power locks, alarms, etc.) are available.

ACC

• The engine is not started.
• Some electrical devices are available (power windows, etc.).

RUN

• Driving position.
• All electrical devices are available.

START

• The engine will start.

NOTE:
In case the ignition switch does not change with the push of the START/STOP ignition button, the key fob may have a low or depleted battery. In this situation, a backup method can be used to operate the ignition switch. Put the nose side of the key fob (side with the mechanical flip key) against the START/STOP ignition button and push to operate the ignition switch.

2024 JEEP Wrangler Review, Price, Features And Mileage (Brochure)

CAUTION!

• Do not press the mechanical key against the START/STOP ignition button.
• Do not use sharp metal objects (e.g. screwdriver etc.) to pry the button out of the ignition switch. This button comes as an assembly and is not removable. This can damage the silicone shield.

Backup Starting Method

Do Not Use Mechanical Key

WARNING!

• When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.
• Never leave children alone in a vehicle, or with access to an unlocked vehicle.
• Allowing children to be in a vehicle unattended is dangerous for several reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector.
• Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the Keyless Enter ‘n Go™ Ignition in the ON/RUN position. A child could operate power windows, and other controls, or move the vehicle.
• Do not leave children or animals inside parked vehicles in hot weather. Interior heat buildup may cause serious injury or death.

CAUTION!
An unlocked vehicle is an invitation for thieves. Always remove the key fob from the vehicle and lock all doors when leaving the vehicle unattended.

NOTE:
When opening the driver’s door with the ignition in the ON/RUN (engine not running) position, a chime will sound to remind you to place the ignition in the OFF position. In addition to the chime, the message will display “Ignition Or Accessory On” in the cluster.

FAQs

Useful Links

View full PDF: 2023 JEEP GLADIATOR Review, Price, Features And Mileage (Brochure)

2024 Jeep Gladiator Instrument Cluster Guide

2024 Jeep Gladiator Fuses And Fuse Box Guide