Kia Niro EV 2021 Automatic Climate Control System User Manual

Introduction

The Kia Niro EV 2021’s automated temperature control system features simple controls and a user-friendly UI that were designed with consumer convenience in mind. You may quickly choose your preferred temperature and allow the system to maintain it during your travel with a few simple modifications. Additionally, the system has capabilities including a defrosting mode that swiftly removes frost or fog from the windshield and front side windows. It provides the best visibility and safety possible during colder weather.

The automatic temperature control system in the Kia Niro EV 2021 prioritizes efficiency while also providing ease of use and convenience. The system serves to enhance the vehicle’s energy economy and contributes to an increased electric driving range by managing temperature and airflow optimally.

Automatic Climate Control System

1. Driver’s temperature control switch
2. AUTO (automatic control) button
3. Front windshield defroster button
4. Rear window defroster button
5. Air conditioning button
6. Air intake control button
7. OFF button
8. Fan speed control switch
9. Mode selection button
10. Climate button
11. Driver only select button
12. HEAT button

NOTICE
Operating the blower when the POWER button is in the ON position could cause the battery to discharge. Operate the blower when the vehicle is on.

Heating and air conditioning automatically

1. Press the AUTO button.
   The modes, fan speeds, air intake and air-conditioning will be con-trolled automatically by setting the temperature.
   
2. Turn the temperature control switch to the desired temperature.

• To turn the automatic operation off, select any button or switch of the following:
  • Mode selection button
  • Air conditioning button
  • Front windshield defroster but-ton (Press the button one more time to deselect the front windshield defroster function. The ‘AUTO’ sign will illuminate on the information display once again.)
  • Air intake control button
  • Fan speed control switch
    The selected function will be controlled manually while other functions operate automatically.
• For your convenience and to improve the effectiveness of the climate control, use the AUTO button and set the temperature to 72 /F (22 /C).

NOTICE
Do not place anything over the sensor located on the instrument panel to ensure better control of the heating and cooling system.

Manual heating and air conditioning
The heating and cooling system can be controlled manually by pressing buttons or turning knob(s) other than the AUTO button.

In this case, the system works sequentially according to the order of buttons or knob(s) selected.

1. Start the vehicle.
2. Set the mode to the desired position.
   For improving the effectiveness of heating and cooling;

    

   • Heating:
   • Cooling:
3. Set the temperature control to the desired position.
4. Set the air intake control to the outside (fresh) air position.
5. Set the fan speed control to the desired speed.
   If air conditioning is desired, turn the air conditioning system on.

Press the AUTO button in order to convert to full automatic control of the system.

Mode selection
The mode selection button controls the direction of the air flow through the ventilation system.

The air flow outlet port is converted as follows:

Face-Level (B, D)

Air flow is directed toward the upper body and face. Additionally, each outlet can be controlled to direct the air discharged from the outlet.

Bi-Level (B, C, D, E, F)
Air flow is directed towards the face and the floor.

Floor-Level (A, C, D, E)

Most of the air flow is directed to the floor, with a small amount of the air being directed to the wind-shield and side window defrosters.

Floor/Defrost-Level (A, C, D, E)
Most of the air flow is directed to the floor and the windshield with a small amount directed to the side window defrosters.

Defrost-Level (A, D)

Most of the air flow is directed to the windshield with a small amount of air directed to the side window defrosters.

Instrument Panel Vents

The outlet vents can be opened or closed separately using the thumb-wheel. (if equipped)
Also, you can adjust the direction of air delivery from these vents using the vent control lever as shown.

Temperature control

The temperature will increase to the maximum (82 /F) by turning the knob to the extreme right.
The temperature will decrease to the minimum (62 /F) by turning the knob to the extreme left.
When turning the knob, the temperature will increase or decrease by 1 /F / 0.5 /C. When set to the lowest temperature setting, the air conditioning will operate continuously.

NOTICE
When starting the vehicle in cold weather using manual temperature control, operate the system in the following method to improve heating.

• Turn off or lower the blower, right after starting the engine.
•  Allow the engine to warm up during this time since the air flow  from the heater is still cold.
  After a few minutes of engine  warm up, turn on or set the fan to a higher level and adjust the temperature setting to hot.

Temperature conversion
You can switch the temperature mode from Centigrade to Fahrenheit as follows:
While pressing the OFF button, press the AUTO button for 3 seconds or more. The display will change from Centigrade to Fahrenheit, or from Fahrenheit to Centi-grade. If the battery has been discharged or disconnected, the temperature mode display will reset to Fahrenheit.

Controlling air intake
This is used to select the outside fresh) air position or recirculated air position.

To change the air intake control position:

• Push the control button.
•  
•  
• 
• Outside (fresh) air position
•  
• With the outside (fresh) air position selected, air enters the vehicle from outside and  is heated or cooled according to the function selected.
•  
• 
• Recirculated air position
  With the outside (fresh) air position selected, air enters the vehicle from outside and With the recirculated air position selected, air from the passenger compartment will be drawn through the heating system and heated or cooled according to the function selected. Prolonged operation of the heater in the recirculated air position (without air conditioning selected) may cause fogging of the windshield and side windows and the air within the passenger compartment may become stale.
  In addition, prolonged use of the air conditioning with the recirculated air position selected will result in excessively dry air in the passenger compartment.
•  
• Controlling fan speed
  The fan speed can be set to the desired speed by operating the fan speed control switch.
•  
• To change the fan speed:
  Turn it right for higher speed, or turn it left for lower speed.

To turn the fan speed control off, press the front blower OFF button.

Air conditioning

• 

Press the A/C button to turn the air conditioning system on (indicator light will illuminate).
Press the button again to turn the air conditioning system off.

WARNING
Reduced Visibility
Continuous use of the climate control system in the recirculated air position may allow humidity to increase inside the vehicle, which may fog the glass and obscure visibility.

WARNING
Recirculated Air
Continued use of the climate control system in the recirculated air position can cause drowsiness or sleepiness, and loss of vehicle control. Set the air intake control to the outside (fresh) air position as much as possible while driving.

WARNING
Sleeping with A/C on
Do not sleep in a vehicle with the air conditioning or heating on, as this may cause serious harm or death due to a drop in the oxygen level and/or body temperature.

Turning heating on or off

• Push the HEAT button to turn the heater on (indicator light will illuminate).
  Push the button again to turn the heater off.
  The air conditioner and heater uses energy from the battery. If you use the heater or air conditioner for too long, distance to empty can be reduced due to increased power consumption.
  Turn off the heater or air conditioner if not necessary.

Turning off the front air climate control

• Press the front blower OFF button to turn off the front air cli-mate control system.
  However, you can still operate the mode and air intake buttons as long as the POWER button is in the ON position.

Displaying climate information (if equipped)

• Press the climate information screen selection button to display climate information on the screen.

Air conditioning for driver only

Press the DRIVER ONLY button and the indicator light illuminates, cold air mostly blows in the direction of the driver’s seat. However, some of the cold air may come out of other seats’ ducts to keep indoor air pleasant.

If you use the button with no passenger in the front passenger seat, energy consumption will be reduced.

Automatic ventilation
The system automatically selects the outside (fresh) air position when the climate control system operates over a certain period of time (5 minutes) in low temperature with the recirculated air position selected.

To cancel or reset the Automatic Ventilation
When the air conditioning system is on, select Face Level mode and press the recirculated air position button more than five times within 3 seconds while pressing A/C button.
When the automatic ventilation is canceled, the indicator blinks 3 times. When the automatic ventilation is activated, the indicator blinks 6 times.

System operation Ventilation

1. Set the mode to the position.
2. Set the air intake control to the outside (fresh) air position.
3. Set the temperature control to the desired position.
4. Set the fan speed control to the desired speed.

Operation Tips

• To keep dust or unpleasant fumes from entering the vehicle through the ventilation system, temporarily set the air intake control to the recirculated air position. Be sure to return the control to the fresh air position when the irritation has passed to keep fresh air in the vehicle. This will help keep the driver alert and comfortable.
• Air for the heating/cooling system is drawn in through the grilles just ahead of the windshield. Care should be taken that these are not blocked by leaves, snow, ice or other obstructions.
• To prevent interior fog on the windshield, set the air intake control to the fresh air position and fan speed to the desired position, turn on the air
  • conditioning system, and adjust the temperature control to desired temperature.

Air conditioning (if equipped)
All Kia Air Conditioning Systems are filled with R-1234yf refrigerant.

1. Start the vehicle. Press the air  conditioning button.
2. Set the mode to the position.
3. Set the air intake control to the outside-air or recirculated air position.
   Adjust the fan speed control and temperature control to maintain maximum comfort.
4. When maximum cooling is desired, set the temperature control to the extreme left position, set the mode control to the MAX A/C position, then set the fan speed control to the highest speed.

CAUTION
Excessive A/C Use
When using the air conditioning system, monitor the temperature gauge closely while driving up hills or in heavy traffic when outside temperatures are high. Air conditioning system operation may cause vehicle overheating. Continue to use the blower fan but turn the air conditioning system off if the temperature gauge indicates vehicle overheating.

CAUTION
When opening the windows in humid weather, air conditioning may create water droplets inside the vehicle. Since excessive water droplets may cause damage to electrical equipment, air conditioning should only be used with the windows closed.

Air conditioning system operation tips

• If the vehicle has been parked in direct sunlight during hot weather, open the windows for a short time to let the hot air inside the vehicle escape.
• To help reduce moisture inside of the windows on rainy or humid days, decrease the humidity inside the vehicle by operating the air conditioning system.
• During air conditioning system operation, you may occasionally notice a slight change in vehicle speed as the air conditioning compressor cycles. This is a nor-mal system operation characteristic.
• Use the air conditioning system every month only for a few minutes to ensure maximum system performance.
• When using the air conditioning system, you may notice clear water dripping (or even puddling) on the ground under the passenger side of the vehicle. This is a normal system operation characteristic.
• Operating the air conditioning system in the recirculated air position provides maximum cooling; however, continual operation in this mode may cause the air inside the vehicle to become stale.
• During cooling operation, you may occasionally notice a misty air  flow because of rapid cooling and humid air intake. This is a normal system operation characteristic.

Climate control air filter (if equipped)
The climate control air filter installed behind the glove box filters the dust or other pollutants that come into the vehicle from the out-side through the heating and air conditioning system.

• A: Outside air
  B: Recirculated air
  C: Climate control air filter
  D: Blower
  E: Evaporator core
  F: Heater core
  If dust or other pollutants accumulate in the filter over a period of time, the air flow from the air vents may decrease, resulting in moisture accumulation on the inside of the windshield even when the outside (fresh) air position is selected. If this happens, have the climate control air filter replaced by an authorized Kia dealer.

NOTICE

• Replace the filter every 15,000 miles or once a year. If the vehicle is being driven in severe conditions, such as dusty or rough roads, more frequent air conditioner filter inspections and changes are required.
• When the air flow rate suddenly decreases, the system should be checked at an authorized Kia dealer.

Air Conditioning refrigerant label

Example

* The actual Air Conditioning refrigerant label in the vehicle may differ from the illustration.

Each symbol and specification on the air conditioning refrigerant label is represented below:

1. Classification of refrigerant
2. Amount of refrigerant
3. Classification of Compressor lubricant
4. Caution
5. Flammable Refrigerant
6. To requires Registered Technician to Service Air Conditioning system

You can find out which air conditioning refrigerant is applied to your vehicle on the label inside of the engine compartment.
Refer to “Refrigerant label” on page 9-10 for more detail on the location of air conditioning refrigerant label.

CAUTION
It is important that the correct type and amount of oil and refrigerant is used, otherwise damage to the vehicle may occur. To prevent dam-age, the air conditioning system in your vehicle should only be serviced by trained and certified technicians.

Checking the amount of air conditioner refrigerant and compressor lubricant
When the amount of refrigerant is low, the performance of the air conditioning is reduced. Overfilling also has a negative impact on the air conditioning system.
Therefore, if abnormal operation is found, have the system inspected by an authorized Kia dealer.

WARNING
The oil and refrigerant in your vehicle’s air conditioning system is under very high pressure. If proper service procedures are not followed an explosion may result. To reduce the risk of serious injury or death, the air conditioning system in your vehicle should only be serviced by trained and certified technicians.

WARNING
Vehicles equipped with R-1234yf
Since the refrigerant is mildly
flammable and operated at high pressure, the air conditioning system should only be serviced by trained and certified technicians.
(Refer to the SAE J2845)
It is important that the correct type and amount of oil and refrigerant are used.

All refrigerants should be reclaimed with proper equipment. Venting refrigerants directly to the atmosphere is harmful to individuals and environment.
Failure to heed these warnings can lead to serious injuries.

Windshield defrosting and defogging
When the windshield is covered with frost or moisture, the front view is blurred, so you should remove the frost and moisture.

Windshield heating
Do not use the or position during cooling operation in extremely humid weather. The difference between the temperature of the outside air and the windshield could cause the outer surface of the windshield to fog up, causing loss of visibility. In this case, set the mode selection to the position and fan speed control to the lower speed.

• For maximum defrosting, set the temperature control to the extreme right/hot position and the fan speed control to the highest speed.
• If warm air to the floor is desired while defrosting or defogging, set the mode to the floor-defrost position.
• Before driving, clear all snow and ice from the windshield, rear window, outside rear view mirrors, and all side windows.
• Clear all snow and ice from the hood and air inlet in the cowl grill to improve heater and defroster efficiency and to reduce the probability of fogging up the inside of the windshield.

Defogging inside windshield with the automatic climate control

1. Set the fan speed to the desired position.
2. Select desired temperature.
3. Press the defroster button
4. The outside (fresh) air position will be selected automatically and the air conditioning will turn on according to the detected ambient temperature.

If the air conditioning and outside (fresh) air position are not selected automatically, adjust the corresponding button manually. If the
position is selected, lower fan speed is adjusted to a higher fan speed.
Defrosting outside windshield with automatic climate control

1. Set the fan speed to the highest position.
2. Set the temperature to the extreme hot (HI) position.
3. Press the defroster button
4. The outside (fresh) air position will be selected automatically and the air conditioning will turn on according to the detected ambient temperature.

Defogging logic
To reduce the possibility of fogging up the inside of the windshield, the air intake or air conditioning is con-trolled automatically according to certain conditions such as  or position.
To cancel automatic defogging logic or return to the automatic defogging logic, do the following.
Turning the defogging logic on or off

1. Turn the POWER button to the ON position.
2. Press the defroster button 
3. While pressing the air conditioning button (A/C), press the air intake control button at least 5 times within 3 seconds.

The recirculation indicator blinks 3 times in 0.5 second of intervals. It indicates that the defogging logic is canceled or returned to the programmed status.
If the battery has been discharged or disconnected, it resets to the defog logic status.

Auto defogging system (if equipped)
Auto defogging reduces the probability of fogging up the inside of the windshield by automatically sensing
the moisture of inside the wind-shield.

The auto defogging system operates when the heater or air conditioning is on.
The indicator illuminates when the auto defogging system senses the moisture on the inside of the wind-shield and operates.
The auto defogging system addresses excess moisture on the inside of the windshield in stages. For example if auto defogging does not defog inside the windshield at step 1 Outside air position, it tries to defog again at step 2 Operating the air conditioning.

1. Outside air position
2. Operating the air conditioning
3. Increasing air flow toward the windshield
4. Blowing air flow toward the wind-shield

Turning the auto defogging system on or off

• Press the front windshield defroster button for 3 seconds when the POWER button is in the ON position.

When the ADS system is canceled, the defroster button indicator will blink 3 times per 0.5 sec.
When the ADS system is reset, the defroster button indicator will blink 6 times per 0.25 sec.

CAUTION
Do not remove the sensor cover located on the upper end of the passenger side windshield glass. Damage to the system parts could occur and may not be covered by your vehicle warranty.

Storage compartment
These compartments can be used to store small items required by the driver or passengers.

• To avoid possible theft, do not leave valuables in the storage compartment.
• Always keep the storage compartment covers closed while driving. Do not attempt to place so many items in the storage compartment that the storage compartment cover cannot close securely.

WARNING
Flammable materials
Do not store, propane cylinders or other flammable/explosive materials in the vehicle. These items may catch fire and/or explode if the vehicle is exposed to hot temperatures for extended periods.

Center console storage

To open the center console storage:

• Pull up the lever.
  Glove box

To open the glove box:

• Push the lever and the glove box will automatically open.
  Close the glove box after use.

WARNING
Glove Box
To reduce the risk of injury in an accident or sudden stop, always keep the glove box door closed while driving.

NOTICE
If the temperature control switch is in the warm or hot position, warm or hot air will flow into the glove box.

Sunglass holder

• To open the sunglass holder:
  Press the cover and the holder will slowly open.
  Place your sunglasses with the lenses facing out. To close the sun-glass holder push it up.

WARNING
Sunglass holder

• Do not keep objects except sunglasses inside the sunglass holder. Such objects can be thrown from the holder in the event of a sud-den stop or an accident, possibly injuring the passengers in the vehicle.
• Do not open the sunglass holder while the vehicle is moving. The rear view mirror of the vehicle can be blocked by an opened sunglass holder.

Luggage box

You can place tools, etc. in the box for easy access.

• Grasp the handle on the edge of the cover and lift it.

Interior features
There are various features inside the vehicle for the convenience of the occupants.

Cup holder
The front and rear seats of the vehicle have cup holders to accommodate cups.

WARNING
Hot liquids
Do not place uncovered cups with hot liquid in the cup holder while the vehicle is in motion. If the hot liquid spills, you may burn yourself. Such a burn to the driver could lead to loss of control of the vehicle.

CAUTION

• Keep your drinks sealed while driving the upper part of the cover (1) and slide down the cover (2) as indicated in the picture below. prevent spilling your drink. If liquid spills, it may get into the vehicle’s electrical/electronic system and damage electrical/electronic parts.
• When cleaning spilled liquids, do not use heat to dry the cup holders. This may damage the cup holder.
• To open the cover, slightly press

Front seat

• To use the cup holder, press the button (1).

The cup holder (2) will appear.

CAUTION
Be careful not to spill drinks in the cup holder. The cup holder may not work.

To use the cup holder space as a storage compartment, turn the cup holder (2) the direction of the arrow.

Cups or small beverage cans may be placed in the cup holders.

Rear seat

Seat warmer (if equipped)
The seat warmer is provided to warm the front seats during cold weather.

With the POWER button in the ON position:

• Push either of the switches to warm the driver’s seat or the front passenger’s seat.

During mild weather or under conditions where the operation of the seat warmer is not needed, keep the switches in the “OFF” position.
Temperature control (Manual) Each time you press the switch, the temperature setting of the seat will change as follows:

Front seat

The seat warmer defaults to the OFF position whenever the POWER button is turned on.

Temperature control (Automatic) The seat warmer starts to automatically control the seat temperature in order to prevent low-temperature burns after being manually turned ON.

Front seat

You may manually press the button to increase the seat temperature. However, it soon returns to the automatic mode again. When pressing the switch for more than 1.5 seconds with the seat warmer operating, the seat warmer will turn OFF. The seat warmer defaults to the OFF position whenever the power button is in the ON position.

NOTICE
With the seat warmer switch in the ON position, the heating system in the seat turns off or on automatically depending on the seat temperature.

WARNING
Seat warmer burns
The seat warmer may cause burns, even at low temperature, if used over a long period of time. Never allow passengers who may not be able to take care of themselves to be exposed to the risk of seat heater burns. These include:

1. Infants, children, elderly or dis-abled persons, or hospital outpatients
2. Persons with sensitive skin or those that burn easily
3. Fatigued individuals
4. Intoxicated individuals
5. Individuals taking medication that can cause drowsiness or sleepiness (sleeping pills, cold tablets, etc.)

Air ventilation seat (if equipped)

The temperature setting of the seat changes according to the switch position.

To ventilate your seat cushion, press the switch (blue color). Each time you press the button, the airflow will change as follows:

The seat warmer (with air ventilation) defaults to the OFF position whenever the POWER button is turned on.

CAUTION
Seat damage
When cleaning the seats, do not use an organic solvent, such as paint thinner, benzene, alcohol and gasoline. Doing so may dam-age the air ventilation seat.

• Do not place heavy or sharp objects on the seat. Those things may damage the air ventilation seat.
• Be careful not to spill liquid, such as water or beverages, on the seat. If you spill some liquid, wipe the seat with a dry towel. Before using the air ventilation seat, dry the seat completely.

Sun visor
Use the sun visor to shield direct light through the front or side windows.

* The actual sun visor lamp in the vehicle may differ from the illustration.

• To use the sun visor, pull it downward.
  To use the sun visor for the side window, pull it downward, unsnap it from the bracket (1) and swing it to the side (2).
• To use the vanity mirror, pull down the visor and slide the mirror cover (3).
  Adjust the sun visor extension forward or backward (4).
  The ticket holder (5) is provided for holding a tollgate ticket (if equipped)

CAUTION
Vanity mirror lamp
If you use the vanity mirror lamp, turn off the lamp before returning the sun visor to its original position; otherwise, it could result in battery discharge and possible sun visor damage.

Power outlet (if equipped)
The power outlet is designed to provide power for mobile tele-phones or other devices designed to operate with vehicle electrical systems.

The devices should draw less than 10 amps with the vehicle on.

• Use the power outlet only when the vehicle is on and remove the accessory plug after use. Using the accessory plug for prolonged periods of time with the vehicle off could cause the battery to discharge.
• Only use 12 V electric accessories which are less than 10 A in electric capacity
  Adjust the air-conditioner or heater to the lowest operating level when using the power outlet.
• Close the cover when not in use.
• Some electronic devices can cause electronic interference when plugged into a vehicle’s power outlet. These devices may cause excessive audio static and malfunctions in other electronic systems or devices used in your vehicle.
• Push the plug in as far as it will go. If good contact is not made, the plug may overheat and the fuse may open.
• Plug in battery equipped electronic devices with reverse cur-rent protection. The current from the battery may flow into the vehicle’s electrical/electronic system and cause system malfunction.

WARNING
Electric shock
Do not put a finger or a foreign object (pen, etc.) into a power outlet and do not touch with a wet hand. You may get an electric shock.

USB charger (if equipped)
The USB charger is designed to recharge batteries of small size electrical devices using a USB cable.

The electrical devices can be recharged when the power button is in ACC/ON position.
The battery charging state may be monitored on the electrical device.
Disconnect the USB cable from the USB port after use.

NOTICE

• Some devices are not supported for fast charging but will be charged with normal speed.
  Use the USB charger when the vehicle is on to prevent battery discharge.
• Only devices that fit the USB port can be used.
  The USB charger can be used only for battery charging purposes.
  Battery chargers cannot be charged.

Wireless smart phone charging system (if equipped)
A wireless smart phone charging system is located in front of the center console.

Firmly close all doors, and turn vehicle on. To start wireless charging, place the smart phone equipped with wireless charging function on the wireless charging pad.
For best wireless charging results, place the smart phone on the center of the charging pad.
The wireless charging system is designed for one smart phone equipped with QI per single usage only. Please refer to the smart phone accessory cover or the smart phone manufacturer homepage to check whether your smart phone supports QI function.

Charging wireless smart phone

1. Remove any object on the smart phone charging pad including the smart key. If there is any foreign object on the pad other than a smart phone, the wireless charging function may not operate properly.
2. Place the smart phone on the  center of the wireless charging pad.
   The indicator light will change to orange once the wireless charging begins. After the charging is complete, the orange light will change to green.

You can choose to turn the wireless charging function to either ON or OFF by selecting the USM on the instrument cluster. (Please refer to “Instrument cluster” on page 5-47 for details).
If the wireless charging does not work, gently move your smart phone around the pad until the charging indicator light turns orange.
Depending on the smart phone, the charging indicator light may not turn green even after the charging is complete.
If the wireless charging is not functioning properly, the orange light will blink and flash for ten seconds then turn off. In such cases, remove the smart phone from the pad and replace it on the pad again, or double check the charging status.
If you leave the smart phone on the charging pad when the vehicle is turned off, the vehicle will alert you through warning messages and sound (applicable for vehicles with voice guidance function) after the  ‘Good bye’ function on the instrument cluster ends.

WARNING
Distracted driving
Driving while distracted can result in a loss of vehicle control that may lead to an accident, severe bodily injury, and death. The driver’s primary responsibility is in the safe and legal operation of a vehicle, and use of any handheld devices, other equipment, or vehicle systems that take the driver’s eyes, attention and focus away from the safe operation of a vehicle or that are not permissible by law should never be used during the operation of the vehicle.

CAUTION
Liquid in Wireless Smart Phone Charger
To prevent liquid from damaging the wireless smart phone charging sys-tem in your vehicle, be sure not to spill liquid over the charging system when charging your phone.

CAUTION
Metal in Wireless Charging System If any metallic object, system such as a coin, is located between the wireless charging system and the smart phone, the charging may be disrupted. Also, the metallic object may heat up and potentially dam-age the charging system. If there is any metallic object between the smart phone and the charging pad, immediately remove the smart phone. Remove the metallic object after it has cooled down.

NOTICE

• When the interior temperature of the wireless charging system rises above a set temperature, the wireless charging system will cease to function. After the interior temperature drops below the threshold, the wireless charging function will resume.
• The wireless charging system may not function properly when there is a heavy accessory cover on the smart phone.
• The wireless charging system will stop when using the wireless smart key search function to pre-vent radio wave disruption.
• The wireless charging system will stop when the smart key is moved out of the vehicle with the vehicle in ON.
• The wireless charging system will stop when any of the doors are opened (applicable for vehicles equipped with smart keys).
• The wireless charging system will stop when the vehicle is turned OFF.
• The wireless charging system will stop when the smart phone is not in complete contact with the wireless charging pad.
• Items equipped with magnetic components, such as credit card, telephone card, bankbook or any transportation ticket, may become damaged during wireless charging.
• Place the smart phone on the center of the charge pad for best results. The smart phone may not charge when placed near the rim of the charging pad. When the smart phone does get charged, it may heat up excessively.
• For smart phones without a built- in wireless charging system, an appropriate accessory has to be equipped in order to use the vehicle’s wireless charging system.
• Smart phones of some manufacturers may display messages on weak current. This is due to the particular characteristic of the smart phone and does not imply a malfunction on wireless charging function.
• The indicator light of some manufacturers’ smart phones may still be orange after the smart phone is fully charged. This is due to the particular characteristic of the smart phone and not a malfunction of the wireless charging system.
• When any smart phone without a wireless charging function or a metallic object is placed on the charging pad, a small noise may sound. This small sound is due to the vehicle discerning compatibility of the object placed on the charging pad. It does not affect your vehicle or the smart phone in any way.
• The wireless cellular phone charging system may not support certain cellular phones, which are  not verified for Qi specification
  When placing your cellular phone  on the charging mat, position the phone in the middle of the mat for optimal charging performance. If your cell phone is off to the side, the charging rate may be less and in some cases the cell phone may experience higher heat conduction.
• When charging some cellular phones with a self-protection feature, the wireless charging speed may decrease and the wireless charging may stop.

This device complies with part 15 of the FCC Rules
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Coat hook (if equipped)
A Coat hook is next to the rear grab handle.

• 

* This actual feature may differ from the illustration.

CAUTION
Hanging clothing
Do not hang heavy clothes, since they may damage the hook.

WARNING
Do not hang other objects, such as hangers or hard objects except clothes. Also, do not put heavy, sharp or breakable objects in the clothing’s pockets. In an accident or when the curtain air bag is inflated, it may cause vehicle damage or personal injury.

Floor mat anchor(s) (if equipped) 

Type A / Type B

When using a floor mat on the front floor carpet, make sure it attaches to the floor mat anchor(s) in your vehicle. This keeps the floor mat from sliding forward.

WARNING
After market floor mat
Do not install after market floor mats that are not capable of being securely attached to the vehicle’s floor mat anchors.
Unsecured floor mats can interfere with pedal operation.

The following must be observed when installing ANY floor mat to the vehicle.

• Ensure that the floor mats are securely attached to the vehicle’s floor mat anchor(s) before driving the vehicle.
• Do not use ANY floor mat that
  cannot be firmly attached to the vehicle’s floor mat anchors.
  Do not stack floor mats on top of one another (e.g. all-weather rubber mat on top of a carpeted floor mat). Only a single floor mat should be installed in each position.

NOTICE
Your vehicle was manufactured with driver’s side floor mat anchors that are designed to securely hold the floor mat in place. To avoid any interference with pedal operation, Kia recommends that only the Kia floor mat designed for use in your vehicle be installed.

Luggage net holder (if equipped)
To keep items from shifting in the cargo area, you can use the holders located in the cargo area to attach the luggage net.

If necessary, we recommend that you contact an authorized Kia dealer.

CAUTION
To prevent damage to the vehicle, care should be taken when carrying fragile or bulky objects in the lug-gage compartment.

WARNING
Luggage net
Always keep your face and body out of the luggage net recoil path and avoid using the luggage net when the straps have visible signs of wear or damage. The luggage net can snap and cause injuries.

Cargo security screen (if equipped)
Use the cargo security screen to hide items stored in the cargo area.

• To use the cargo security screen, pull the handle backward and insert the edges into the slots.
•  
• WARNING
  Cargo Security Screen

Do not place objects on the cargo security screen. Such objects may be thrown about inside the vehicle and possibly injure vehicle occupants during an accident or when braking.

WARNING
Do not place luggage on the cargo security screen. This may cause the security screen to become damaged or malformed.

Exterior features

If the vehicle has a roof rack, you can load cargo on top of your vehicle.

Roof rack (if equipped)

Crossbars and fixing components can be installed on the roof rack to carry cargo. Those may be obtained from an authorized Kia dealer or other qualified shop.

NOTICE

• The crossbars (if equipped) should be placed in the proper load carrying positions prior to placing items onto the roof rack.
• If the vehicle is equipped with a  sunroof, be sure not to position cargo onto the roof rack in such a way that it could interfere with sunroof operation.
• When the roof rack is not being used to carry cargo, the crossbars  may need to be repositioned if wind noise is detected.

CAUTION
Loading Roof Rack

• When carrying cargo on the roof rack, take the necessary precautions to make sure the cargo does not damage the roof of the vehicle.
• When carrying large objects on the roof rack, make sure they do not exceed the overall roof length or width.
• When you are carrying cargo on the roof rack, do not operate the sunroof (if equipped). This can damage the sunroof.
• The following specification is the maximum weight that can be loaded onto the roof rack. Distribute the load as evenly as possible across the crossbars (if equipped) and roof rack and secure the load firmly.

ROOF  RACK
220 lbs. (100 kg) EVENLY DISTRIBUTED

Loading cargo or luggage in excess of the specified weight limit on the roof rack may dam-age your vehicle.

WARNING

• The vehicle center of gravity will be higher when items are loaded onto the roof rack. Avoid sudden starts, braking, sharp turns, abrupt maneuvers or high speeds that may result in loss of vehicle control or rollover resulting in an accident.
• Always drive slowly and turn corners carefully when carrying items on the roof rack. Severe wind updrafts, caused by passing vehicles or natural causes, can cause sudden upward pressure on items loaded on the roof rack. This is especially true when carrying large, flat items, such as wood panels or mattresses. This could cause the items, to fall off the roof rack and cause damage to your vehicle or others around you.
• To prevent damage or loss of cargo while driving, check frequently before or while driving to make sure the items on the roof rack are securely fastened.

WARNING
Driving with roof load
Always drive slow and turn corners carefully when carrying items on the roof rack. The vehicle’s center of gravity will be higher when items are loaded onto the roof rack.

Audio system

NOTICE
If you install an after market HID head lamp, your vehicle’s audio and electronic device may malfunction.

* If your vehicle is equipped with multimedia system, refer to a separately supplied manual for detailed information.

Antenna
This vehicle is equipped with a shark fin antenna.

Shark fin antenna

The shark fin antenna will receive the transmit data.

USB port
You can use an USB port to plug in an USB.

How vehicle radio works

FM reception

AM and FM radio signals are broad-cast from transmitter towers located around your city. They are intercepted by the radio antenna on your vehicle. This signal is then processed by the radio and sent to your vehicle speakers.

However, in some cases the signal coming to your vehicle may not be strong and clear.
This can be due to factors, such as the distance from the radio station, closeness of other strong radio stations or the presence of buildings, bridges or other large obstructions in the area.

AM reception

AM broadcasts can be received at greater distances than FM broad-casts. This is because AM radio waves are transmitted at low fre-quencies. These long distance, low frequency radio waves can follow the curvature of the earth rather than traveling straight. In addition, they curve around obstructions resulting in better signal coverage.

FM radio station

FM broadcasts are transmitted at high frequencies and do not bend to follow the earth’s surface. Because of this, FM broadcasts generally begin to fade within short distances from the station. Also, FM signals are easily affected by buildings, mountains, and obstructions. This can lead to undesirable or unpleasant listening conditions which might lead you to believe a problem exists with your radio.
The following conditions are normal and do not indicate radio trouble:

• Fading – As your vehicle moves away from the radio station, the signal will weaken and sound will begin to fade. When this occurs, we suggest that you select another station with a stronger signal.

• Flutter/Static – Weak FM signals or large obstructions between the transmitter and your radio can disturb the signal causing static or fluttering noises to occur. Reducing the treble level may lessen this effect until the disturbance clears.
• Station Swapping – As an FM signal weakens, another more powerful signal near the same frequency may begin to play. This is because your radio is designed to lock onto the clearest signal. If this occurs, select another station with a stronger signal.

• Multi-Path Cancellation – Radio  signals being received from several directions can cause distortion or fluttering. This can be caused by a direct and reflected signal from the same station, or by signals from two stations with close frequencies. If this occurs, select another station until the condition has passed.

Using a cellular phone or a two-way radio
When a cellular phone is used inside the vehicle, noise may be produced from the audio system. This does not mean that something is wrong with the audio equipment. In such a case, try to operate mobile devices as far from the audio equipment as possible.
When using a communication system such as a cellular phone or a radio set inside the vehicle, a separate external antenna must be fitted. When a cellular phone or a radio set is used with an internal antenna alone, it may interfere with the vehicle’s electrical system and adversely affect safe operation of the vehicle.

WARNING
Cell phone use
Do not use a cellular phone while driving. Stop at a safe location to use a cellular phone.

WARNING
Distracted driving
Driving while distracted can result in a loss of vehicle control that may lead to an accident, severe bodily injury, or death. The driver’s primary responsibility is the safe and legal operation of the vehicle, and the use of any handheld devices, other equipment, or vehicle systems that take the driver’s eyes, attention, and focus away from the safe operation of the vehicle, or that are not permissible by law, should never be used during the operation of the vehicle.

Declaration of Conformity

FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These lim-its are designed to provide reason-able protection against harmful interference in a residential installa-tion.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer-ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
  Increase the separation between the equipment and receiver.
  Connect the equipment into an outlet on a circuit different from
  that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CAUTION
Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum 8 in (20 cm) between the and your body. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC.

FAQs

Useful Links

View Full User Guide: Kia Niro EV 2021| Auto User Guide
Download Manuals: Owner’s Manuals and Documents | Kia