2023 Kia Sportage Lighting and Wipers and Washers 

In the world of automobile innovation, the 2023 Kia Sportage stands out as a model that combines cutting-edge technology with useful features. Its lights, wipers, and washers are good examples of this. These features not only improve sight and safety, but they also make driving easier and more enjoyable. The Sportage’s lighting is at the heart of safety and has a wide range of uses. The Sportage makes sure that every drive is clear and precise. It has powerful LED headlights that light up the road ahead and daytime running lights that make it easier to see during the day. The Sportage is also flexible, as shown by the fact that it has rain-sensing wipers that make sure vision is good even when it’s raining. The wipers and washers on the Sportage can do more than just clean the windshield. Rain-sensing wipers turn on instantly when it starts to rain, responding naturally to changes in the weather. Working with the windshield wipers, the windshield washer device cleans the windshield, making it easier to see and safer to drive. The 2023 Kia Sportage is designed to meet the needs of current drivers who want a good balance of comfort and safety. The fact that improved lighting, wipers, and washers are built into the car shows how committed Kia is to improving the driving experience and making a car that is both innovative and useful on the road.

2023 KIA SPORTAGE Specs, Price, Mileage, Features and Torque

Lighting

This vehicle is equipped with a variety of lights to illuminate the interior and exterior of the vehicle.

CAUTION
To prevent the battery from being discharged, do not leave the headlamp and interior light on for a prolonged time while the engine is not running.

Battery saver function

The purpose of this feature is to prevent the battery from being discharged if the lights are left in the ON position. The system automatically shuts off the parking lights after the engine is off and the driver’s door is opened. However, the position lamps stay ON even when the driver-side door is opened if the light switch is operated after the engine is turned off. If necessary, to keep the lamps on turn the position lamps OFF and ON again using the headlamp switch on the steering column after the engine is turned off.

Headlamp delay function

If you place the ignition switch or ENGINE START/STOP button in the ACC or OFF position with the headlamps ON, the headlamps (and/or parking lights) remain on for about 5 minutes. However, with the engine off if the driver’s door is opened and closed, the head-lamps (and/or parking lights) are turned off after 15 seconds. The headlamps (and/or parking lights) can be turned off by pressing the lock button on the smart key twice or turning the light switch to the OFF or AUTO position. However, if you turn the light switch to the AUTO position when it is Feature of your vehicle
dark outside, the headlamps will not be turned off.
You can activate or deactivate the Head-lamp Delay function from the User Set-tings Mode in the LCD display. 

NOTICE
If the driver exits the vehicle through another door besides the driver door, the battery saver function does not operate and the headlamp delay function does not turn OFF automatically. This may cause the battery to discharge. To avoid battery discharge, turn OFF the headlamps manually from the headlamp switch before exiting the vehicle.

Daytime Running Light (DRL)

The Daytime Running Light (DRL) can make it easier for others to see the front of your vehicle during the day. The DRL can be helpful in many different driving conditions, and it is especially helpful after dawn and before sunset. The DRL will turn the dedicated lamp OFF when:

• The headlamps are ON.
• The vehicle is off.
• The front fog light is on. (if equipped)
• Engaging the parking brake.

Lighting control

The light switch has a headlamp and a position lamp position.

To operate the lights, turn the knob at the end of the control lever to one of the following positions:

1. OFF position
2. Auto light position
3. Position & Taillamp
4. Headlamp position

Position & Taillamp

When the light switch is in the position lamp position, the front position lamp, taillamp, and the license plate lamp will turn ON.

Headlamp (Low Beam)

When the light switch is in the headlamp position, headlamp (low beam), tail, license light will turn ON.

NOTICE
The ignition switch or ENGINE START/STOP button must be in the ON position to turn on the headlamps.

Auto light

When the light switch is in the AUTO light position, the taillamps and head-lamps will turn ON or OFF automatically depending on the amount of light out-side the vehicle.

CAUTION

•  Never place anything over the sensor (1) located on the instrument panel as this will ensure better auto-light system control.
• Don’t clean the sensor using a window cleaner, the cleaner may leave a light film which could interfere with sensor operation.
• If your vehicle has window tint or other types of metallic coating on the front windshield, the Auto light system may not work properly.

Operating high beam

To turn on the high beam headlamp:

• Push the lever away from you The lever will return to its original position. The high beam indicator will light when the headlamp high beams are switched on.

WARNING
High beams
Do not use high beam when there are other vehicles in front of or approaching your vehicle. Using high beam could obstruct the other driver’s vision.

To flash the headlamps:

• Pull the lever towards you.

It will return to the normal (low beam) position when released. The head-lamp switch does not need to be on to use this flashing feature.

Operating turn signals and lane change signals

The ENGINE START/STOP button must be on for the turn signals to function. To turn on the turn signals:
Move the lever up or down (A). The green arrow indicators on the instrument panel indicate which turn signal is operating. They will self-cancel after a turn is completed. If the indicator continues to flash after a turn, manually return the lever to the OFF position. To signal a lane change:
Move the turn signal lever slightly and  hold it in position (B). The lever will return to the OFF position when released.
If an indicator stays on and does not flash or if it flashes abnormally, one of the turns signal bulbs may be burned out and will require replacement.

One-touch lane change function
To activate a one-touch lane change function, move the turn signal lever slightly and then release it. The lane change signals will blink 3, 5, or 7 times.
You can activate or deactivate the One Touch Turn Signal function or choose the number of blinking (3, 5, or 7) by selecting “Vehicle →Lights → One Touch Turn Signal”.

NOTICE
If an indicator flash is abnormally quick or slow, a bulb may be burned out or have a poor electrical connection in the circuit. The bulb may require replacement.

Operating front fog light equipped)

Fog lights are designed to provide improved visibility when visibility is poor due to fog, rain or snow, etc.

The fog lights will turn on when the fog light switch (1) is turned to the on position after the headlamp is turned on.

To turn off the fog lights:

• Turn the fog light switch (1) to the ON position.

CAUTION
When in operation, the fog lights consume large amounts of vehicle electrical power. Only use the fog lights when visibility is poor.

High Beam Assist (HBA)

(switches between high beam and low beam) depending on the brightness of detected vehicles and certain road conditions.

Detecting sensor

Front view camera

The front view camera is used as a detecting sensor to detect ambient light and brightness while driving.
Refer to the picture above for the detailed location of the detecting sensor.

NOTICE
Always keep the front view camera in good condition to maintain optimal performance of High Beam Assist.

High Beam Assist setting

A: Vehicle Settings

1. Lights
2.  High Beam Assist
   With the ENGINE START/STOP button in the ON position, select ‘Lights → High Beam Assist’ from the Settings menu to turn on High Beam Assist and deselect to turn off the function.

WARNING
For your safety, adjust your high beam settings only after parking the vehicle at a safe location.

High Beam Assist operation

Display and control

• After selecting ‘High Beam Assist’ in the Settings menu, High Beam Assist will operate by following the procedure below.
  • Place the headlamp switch in the AUTO position and push the headlamp lever towards the instrument cluster. The High Beam Assist ( ) indicator light will appear on the cluster and the function will be enabled.
  • When the function is enabled, high beam will turn on when vehicle speed is above 25 mph (40 km/h). When vehicle speed is below 15 mph (25 km/h), high beam will not turn on.
  • The High Beam ( ) indicator light will appear on the cluster when high beam is on.
• When High Beam Assist is operating, if the headlamp lever or switch is used, the function operates as follows:
  • If the headlamp lever is pulled towards you when the high beam is off, the high beam will turn on with-out High Beam Assist cancelled. When you let go of the headlamp lever, High Beam Assist will turn on again.
  • If you push the light switch towards the instrument cluster, High Beam is turned on and High Beam Assist is released.
  • If the headlamp lever is pulled towards you when the high beam is on by High Beam Assist, low beam will be on and the function will turn off.
  • If the headlamp switch is placed from AUTO to another position (headlamp/position/off), High Beam Assist will turn off and the corresponding lamp will turn on.
•  When High Beam Assist is operating, high beam switches to low beam if any of the following conditions occur:
  • When the headlamp of an oncoming vehicle is detected.
  • When the taillamp of a vehicle in front is detected.
  • When the headlamp or taillamp of a motorcycle or a bicycle is detected.
  • When the surrounding ambient light is bright enough that high beams are not required.
  • When streetlights or other lights are detected.

Malfunction and limitations
Malfunction

A: Check High Beam Assist (HBA) system When High Beam Assist is not working properly, the ‘Check High Beam Assist (HBA) system’ warning message will appear and warning light ( ) will appear on the cluster. Have the function inspected by an authorized Kia dealer.

Limitations
High Beam Assist may not work properly in the following situations:

• Light from a vehicle is not detected because of lamp damage, or because it is hidden from sight, etc.
•  Headlamp of a vehicle is covered with dust, snow or water.
•  A vehicle’s headlamps are off but the fog lamps are on and etc.
•  There is a lamp that has a similar shape as a vehicle’s lamp.
• Headlamps have been damaged or not repaired properly.
• Headlamps are not aimed properly.
•  Driving on a narrow curved road, rough road, uphill or downhill.
•  Vehicle in front is partially visible on a crossroad or curved road.
• There is a traffic light, reflecting sign, flashing sign or mirror ahead.
•  There is a temporary reflector or flash ahead (construction area).
•  The road conditions are bad such as being wet, iced or covered with snow.
• A vehicle suddenly appears from a curve.
•  The vehicle is tilted from a flat tire or is being towed.
•  Light from a vehicle is not detected because of exhaust fume, smoke, fog, snow, etc.

NOTICE
Depending on the instrument cluster specification or theme, images or colors may be displayed differently.

WARNING

•  At times, High Beam Assist may not work properly. The function is for your convenience only. It is the responsibility of the driver for safe driving practices and always check the road conditions for your safety.
• When High Beam Assist does not operate normally, change the head-lamp position manually between high beam and low beam.

Wipers and washers

The wipers and washers remove foreign substances from the windshield and rear window, helping to maintain visibility.

A: Wiper speed control

• MIST – Single wipe
• OFF – Off
•  INT – Intermittent wipe
  AUTO* – Auto control wipe
•  LO – Low wiper speed
•  HI – High wiper speed
  B: Intermittent control wipe time adjustment/Auto control wipe time adjustment*
  C: Wash with brief wipes (Pull the lever towards you)
  D: Rear wiper/washer control
• HI – Continuous wipe
•  LO – Intermittent wipe
• OFF – Off
  E: Wash with brief wipes (Rear/Push lever away from you)
  *: if equipped

Windshield wipers
Operate as follows when the ignition switch or ENGINE START/STOP button is ON.

•  MIST: For a single wiping cycle, move the lever to this position and release it. The wipers will operate continuously if the lever is held in this position.
• OFF: Wiper is not in operation
•  INT: Wiper operates intermittently at the same wiping intervals. Use this mode in light rain or mist. To vary the speed setting, turn the speed control knob.
• LO: Normal wiper speed
• HI: Fast wiper speed

NOTICE
If there is heavy accumulation of snow or ice on the windshield, defrost the windshield for about 10 minutes, or until the snow and/or ice is removed before using the windshield wipers to ensure proper operation. If you do not remove the snow and/or ice before using the wiper and washer, it may damage the wiper and washer system.

WARNING
Do not use the washer in freezing temperatures without first warming the windshield with the defrosters; the washer solution could freeze on the windshield and obscure your vision.

Auto control (if equipped)

The rain sensor (A) located on the upper end of the windshield glass senses the amount of rainfall and controls the wiping cycle for the proper interval. The more it rains, the faster the wiper operates. When the rain stops, the wiper stops. To vary the speed setting, turn the speed control knob (B).
If the wiper switch is set in AUTO mode when the ignition switch or ENGINE START/STOP button is ON, the wiper will operate once to perform a self-check of the system. Set the wiper to OFF position when the wiper is not in use.

WARNING
When the ignition switch or ENGINE START/STOP button is ON and the windshield wiper switch is placed in the AUTO mode, use caution in the following situations to avoid any injury to the hands or other parts of the body:

• Do not touch the upper end of the windshield glass facing the rain sensor.
•  Do not wipe the upper end of the windshield glass with a damp or wet cloth.
• Do not put pressure on the windshield glass.

CAUTION

•  When washing the vehicle, set the wiper switch in the OFF position to stop the auto wiper operation.
  The wiper may operate and be damaged if the switch is set in the AUTO mode while washing the vehicle.
•  Do not remove the sensor cover located on the upper end of the passenger side windshield glass. Damage to system parts could occur and may not be covered by your vehicle warranty.
• When starting the vehicle in winter,  set the wiper switch in the OFF position. Otherwise, wipers may operate and ice may damage the windshield wiper blades. Always remove all snow and ice and defrost the windshield properly prior to operating the windshield wipers.
• When tinting the windshield, be careful of any fluid getting into the sensor located in the top center of the front windshield. It may damage the related parts.

Operating windshield washers

1. Move the wiper speed control switch to the OFF position.
2. Pull the lever gently toward you to spray washer fluid on the windshield and to run the wipers 1-3 cycles. Use this function when the windshield is dirty. The spray and wiper operation will continue until you release the lever.
   If the washer does not work, check the washer fluid level. If the fluid level is not sufficient, you will need to add appropriate non-abrasive windshield washer fluid to the washer reservoir.
   The reservoir filler neck is located in the front of the engine compartment on the passenger side.

CAUTION
To prevent possible damage to the washer pump, do not operate the washer when the fluid reservoir is empty.

WARNING
Do not use the washer in freezing temperatures without first warming the windshield with the defrosters; the washer solution could freeze on the windshield and obscure your vision.

CAUTION

• To prevent possible damage to the wipers or windshield, do not operate the wipers when the windshield is dry.
• To prevent damage to the wiper  blades, do not use gasoline, kerosene, paint thinner, or other solvents on or near them.
•  To prevent damage to the wiper arms and other components, do not attempt to move the wipers manually.
•  To prevent possible damage to the wipers and washer system, use anti-freezing washer fluids in the winter season or cold weather.

Operating rear window wiper and washer switch

The rear window wiper and washer switch is located at the end of the wiper and washer switch lever.

• Turn the switch to the desired position to operate the rear wiper and washer.
  
•  HI – Normal wiper operation
  LO – Intermittent wiper operation
• OFF – Wiper is not in operation
•  Push the lever away from you to spray rear washer fluid and to run the rear wipers several times.
  

The spray and wiper operation will continue until you release the lever. When the front wiper is activated and the gear is switched to R (Reverse) posi-tion, the rear wiper will be activated once to provide better visibility.

Heated washer nozzle (if equipped)

The heated washer nozzle function defreeze the washer nozzles in freezing weather.  The heated washer nozzle will turn on and off automatically when the ignition switch or ENGINE START/STOP button is in ON position or when the engine is running in the following conditions:

• Turns ON when the outside temperature is below 41 °F, and OFF when it is over 50 °F.
•  The washer fluid refreezing speed may be slower when the ignition switch or ENGINE START/STOP button is in ON position than compared to when the engine is running.
•  When the ignition switch or ENGINE START/STOP button is in ON position, after approximately 20 minutes of operation, the system will turn off automatically to prevent possible battery discharge.
•  After the engine is running, the washer fluid will defrost for approximately after 5 ~ 10 minutes.
•  If the engine has been started within the operating temperature, the heated nozzle remains ON even approximately after 20 minutes.

NOTICE

The heated washer nozzle may not function properly under the following conditions:

• The washer fluid in the washer reservoir is frozen.
•  The outside temperature sensor is malfunctioning.

FAQ