2022 Lincoln Corsair Cruise Control and Adaptive Cruise Control System

With its advanced Cruise Control and Adaptive Cruise Control system, the 2022 Lincoln Corsair takes safety and ease while driving to a whole new level. The usual Cruise Control feature makes it easy for drivers to stay at a set speed, which is great for long trips on the highway. In the 2022 Lincoln Corsair, the Adaptive Cruise Control device adds another level of intelligence on top of regular cruise control. This cutting-edge system uses high-tech sensors and cameras to keep an eye on the road and traffic around it in real time. The Adaptive Cruise Control makes driving safe and stress-free by changing the speed of the car automatically to keep a safe distance from the car in front of it. The 2022 Lincoln Corsair’s Cruise Control and Adaptive Cruise Control systems show how the brand is dedicated to combining cutting-edge technology with luxury driving, whether you’re driving through a busy city or cruising on the open highway.

WHAT IS CRUISE CONTROL

Cruise control lets you maintain a set speed without keeping your foot on the accelerator pedal.

Requirements
Use cruise control when the vehicle speed is greater than 20 mph (30 km/h).

SWITCHING CRUISE CONTROL ON AND OFF

WARNING: Do not use cruise control on winding roads, in heavy traffic, or when the road surface is slippery. This could result in loss of vehicle control, serious injury, or death.

The cruise controls are on the steering wheel.

Switching Cruise Control On

Press the button to put the system in standby mode.

 

Switching Cruise Control Off

Press the button when in standby mode or switch the ignition off.

 

Note: When you switch cruise control off the set speed clears.

SETTING THE CRUISE CONTROL SPEED

WARNING: When you are going downhill, your vehicle speed could increase above the set speed. The system does not apply the brakes.

Drive to the speed you prefer.

Press either button to set the current speed.

 

 

 

Take your foot off the accelerator pedal.
Note: The indicator changes color in the information display.

Changing the Set Speed

Press and release the button to increase the set speed in small increments.

 

Press and hold the button to accelerate. Release the button when you reach your preferred speed.

Press and release the button to decrease the set speed in small increments.

 

Press and hold the button to decelerate. Release the button when you reach your preferred speed.

Note: If you accelerate by pressing the accelerator pedal, the set speed does not change. When you release the accelerator pedal, your vehicle returns to the speed that you previously set.

CANCELING THE SET SPEED

Press the button, or tap the brake pedal to cancel the set speed.

 

Note: The system remembers the set speed.

Note: The system cancels if the vehicle speed drops below 10 mph (16 km/h) under the set speed when driving uphill.

RESUMING THE SET SPEED

Press the button.

 

CRUISE CONTROL INDICATORS

Illuminates when you switch the system on.

 

 

HOW DOES ADAPTIVE CRUISE CONTROL WITH STOP-AND-GO WORK
Adaptive cruise control with stop-and-go uses radar and camera sensors to adjust the speed of your vehicle to maintain a set gap from the vehicle in front of you in the same lane while following it to a complete stop. You can also engage the system to follow a vehicle in front of you and adjust the set speed while stopped.

WHAT IS ADAPTIVE CRUISE CONTROL WITH LANE-CENTERING
Adaptive cruise control with lane centering uses radar and camera sensors to help keep your vehicle in the lane by applying continuous assistance steering torque input toward the lane center on highways.
Note: The adaptive cruise control gap setting operates normally.

WHAT IS INTELLIGENT ADAPTIVE CRUISE CONTROL
Intelligent adaptive cruise control combines speed sign recognition with adaptive cruise control to adjust the cruise set speed to the speed limit detected by the speed sign recognition system. For example, if the speed sign recognition system detects a 50 mph (80 km/h) speed limit, the cruise set speed is updated to 50 mph (80 km/h) +/- the driver’s selected speed offset.

Note: The adaptive cruise control gap setting operates normally.

ADAPTIVE CRUISE CONTROL PRECAUTIONS – VEHICLES WITH: ADAPTIVE CRUISE CONTROL WITH LANE-CENTERING

Adaptive cruise control precautions apply to lane centering unless stated otherwise or contradicted by a lane centering precaution.

WARNING: Do not use the system when towing a trailer. Failure to follow this instruction could result in the loss of control of your vehicle, personal injury, or death.

WARNING: Do not use the system if any changes or modifications to the steering wheel have been made. Any changes or modifications to the steering wheel could affect the functionality or performance of the system. Failure to follow this instruction could result in the loss of control of your vehicle, personal injury, or death.

ADAPTIVE CRUISE CONTROL PRECAUTIONS – VEHICLES WITH: ADAPTIVE CRUISE CONTROL WITH STOP-AND-GO

WARNING: You are responsible for controlling your vehicle at all times. The system is designed to be an aid and does not relieve you of your responsibility to drive with due care and attention. Failure to follow this instruction could result in the loss of control of your vehicle, personal injury, or death.

WARNING: Pay close attention to changing road conditions such as entering or leaving a highway, on roads with intersections or roundabouts, roads without visible lanes of travel, and on roads that are winding, slippery, unpaved, or steep slopes.

WARNING: The system does not control speed in low traction conditions or extremely steep slopes. The system is designed to be an aid and does not relieve you of your responsibility to drive with due care and attention. Failure to follow this instruction could result in personal injury.

WARNING: The system is not a crash warning or avoidance system.

WARNING: Do not use the system when towing a trailer that has aftermarket electronic trailer brake controls. Failure to follow this instruction could result in the loss of control of your vehicle, personal injury, or death.

WARNING: Do not use tire sizes other than those recommended because this can affect the normal operation of the system. Failure to do so may result in a loss of vehicle control, which could result in serious injury.

WARNING: Do not use the system with a snow plow blade installed.

WARNING: Do not use the system in poor visibility, for example, fog, heavy rain, spray, or snow.

When Following a Vehicle

WARNING: When following a vehicle that is braking, your vehicle does not always decelerate quickly enough to avoid a crash without driver intervention. Apply the brakes when necessary. Failure to follow this instruction could result in personal injury or death.

Hilly Condition Usage
You should select a lower gear when the system is active in situations such as prolonged downhill driving on steep grades, for example in mountainous areas. The system needs additional engine braking in these situations to reduce the load on the vehicle’s regular brake system to prevent it from overheating.

Note: An audible alarm sounds and the system shuts down if it applies brakes for an extended period. This allows the brakes to cool. The system functions normally again after the brakes cool.

ADAPTIVE CRUISE CONTROL LIMITATIONS – VEHICLES WITH: ADAPTIVE CRUISE CONTROL WITH LANE-CENTERING

Adaptive cruise control limitations apply to lane centring unless stated otherwise or contradicted by a lane centring limitation.

The system may not correctly operate in any of the following conditions:

• The lane is too narrow or wide.
• The system does not detect at least one lane marking or when lanes merge or split.
• Limited steering torque input is applied.
• Areas under construction or new infrastructure.
• When modifications to the steering system have been made.
• When using a spare tire.

Note: The driving assistance torque is limited and may not be sufficient for all driving situations such as driving through tight curves or driving through curves at high speeds.

Note: In exceptional conditions, the system may deviate from the center line.

ADAPTIVE CRUISE CONTROL LIMITATIONS – VEHICLES WITH: ADAPTIVE CRUISE CONTROL WITH STOP-AND-GO

Sensor Limitations

WARNING: On rare occasions, detection issues can occur due to the road infrastructures, for example, bridges, tunnels, and safety barriers. In these cases, the system may break late or unexpectedly. At all times, you are responsible for controlling your vehicle, supervising the system, and intervening, if required.

WARNING: If the system malfunctions, have your vehicle checked as soon as possible.
WARNING: Large contrasts in outside lighting can limit sensor performance.
WARNING: The system only warns of vehicles detected by the radar sensor. In some cases, there may be no warning or a delayed warning. Apply the brakes when necessary. Failure to follow this instruction could result in personal injury or death.
WARNING: The system may not detect stationary or slow-moving vehicles below 6 mph (10 km/h).
WARNING: The system does not detect pedestrians or objects on the road.
WARNING: The system does not detect oncoming vehicles in the same lane.
WARNING: The system may not operate properly if the sensor is blocked. Keep the windshield free from obstruction.
WARNING: The sensor may incorrectly track lane markings as other structures or objects. This can result in a false or missed warning.

The camera is mounted on the windshield behind the interior mirror.

The radar sensor is in the lower grille.

Note: You cannot see the sensor. It is behind a fascia panel.

Note: Keep the front of your vehicle free of dirt, metal badges, or objects. Vehicle front protectors, aftermarket lights, additional paint, or plastic coatings could also degrade sensor performance. A message displays if something obstructs the camera or the sensor. When something blocks the sensor, the system cannot detect a vehicle ahead and does not function.
The radar sensor has a limited field of view. It may not detect vehicles at all or detect a vehicle later than expected in some situations. The lead vehicle image does not illuminate if the system does not detect a vehicle in front of you.

Detection issues can occur:

1. When driving on a different line than the vehicle in front.
2. With vehicles that edge into your lane. The system can only detect these vehicles once they move fully into your lane.
3. There may be issues with the detection of vehicles in front when driving into and coming out of a bend or curve in the road.

In these cases, the system may break late or unexpectedly.
If something hits the front end of your vehicle or damage occurs, the radar-sensing zone may change. This could cause missed or false vehicle detection.
Optimal system performance requires a clear view of the road by the windshield-mounted camera. Optimal performance may not occur if:

• The camera is blocked.
• There is poor visibility or lighting conditions.
• There are bad weather conditions.

SWITCHING ADAPTIVE CRUISE CONTROL ON AND OFF

The cruise controls are on the steering wheel.

Switching Adaptive Cruise Control On

Press the button to set the system in standby mode.

 

 

The indicator, current gap setting, and set speed appear in the information display.

Switching Adaptive Cruise Control Off

Press the button when the system is in standby mode, or switch the ignition off.

 

Note: You erase the set speed when you switch the system off.

Automatic Cancellation or Deactivation
The system may cancel if:

• The tires lose traction.
• You apply the parking brake.

The system may cancel and set the parking brake if:

• You unbuckle the seatbelt and open the driver’s door after you stop your vehicle.
• Your vehicle is at a stop continuously for more than three minutes.

The system may turn off or prevent activating when requested if:

• The vehicle has a blocked sensor.
• The brake temperature is too high.
• There is a failure in the system or a related system.

SETTING THE ADAPTIVE CRUISE CONTROL SPEED

Drive to the speed you prefer.

Press either button to set the current speed.

 

 

 

Take your foot off the accelerator pedal.

The indicator, current gap setting, and set speed appear in the information display.

Setting the Adaptive Cruise Speed from a Complete Stop

Press and release either button while keeping the brake pedal fully pressed.

 

 

The set speed adjusts to 20 mph (30 km/h).

The indicator, current gap setting, and set speed appear in the information display.

Note: The system activates from a complete stop only when it detects a lead vehicle nearby.

Manually Changing the Set Speed

Press and release to increase the set speed in small increments.

Press and release to decrease the set speed in small increments.

Press and hold either button to change the set speed in large increments. Release the button when the set speed shown is equal to the speed you prefer.
Press the accelerator or brake pedal until you reach the speed you prefer. Press either button to select the current speed as the set speed.
The system may apply the brakes to slow the vehicle to the new set speed. The set speed displays continuously in the information display when the system is active.

SETTING THE ADAPTIVE CRUISE CONTROL GAP

Press the button to cycle through the four gap settings.

 

 

The selected gap appears in the instrument cluster display as shown by the bars in the image.

Note: The gap setting is time-dependent and therefore, the distance adjusts with your vehicle speed.

Note: It is your responsibility to select a gap appropriate to the driving conditions.

Adaptive Cruise Control Gap Settings

Graphic Display, Bars Indicated Between Vehicles	Gap Distance	Dynamic Behavior
1	Closest.	Sport.
2	Close.	Normal.
3	Medium.	Normal.
4	Far.	Comfort.

Each time you switch the system on, it selects the last chosen gap setting.

Following a Vehicle
When a vehicle ahead of you enters the same lane or a slower vehicle is ahead in the same lane, the vehicle speed adjusts to maintain the gap setting.

Note: When you are following a vehicle and you switch on a turn signal lamp, adaptive cruise control may provide a small, temporary acceleration to help you pass.
Your vehicle maintains a consistent gap from the vehicle ahead until:

• The vehicle in front of you accelerates to a speed above the set speed.
• The vehicle in front of you moves out of the lane you are in.
• You set a new gap distance.

The system applies the brakes to slow down your vehicle to maintain a safe gap distance from the vehicle in front of you. The system only applies limited braking. You can override the system by applying the brakes.

Note: The brakes may emit noise when applied by the system.
If the system determines that its maximum braking level is not sufficient, an audible warning sounds, a message appears in the instrument cluster display and an indicator flashes when the system continues to brake. Take immediate action.

CANCELING THE SET SPEED

Press the button or tap the brake pedal.

 

The set speed does not erase.

RESUMING THE SET SPEED

Press the button.

 

Your vehicle speed returns to the previously set speed and gap setting. The set speed displays continuously in the information display when the system is active.

Note: Only use a resume if you are aware of the set speed and intend to return to it.

Resuming the Set Speed from a Complete Stop
If your vehicle follows a vehicle to a complete stop and remains stationary for less than three seconds, your vehicle accelerates from a stationary position to follow the vehicle ahead.
If your vehicle follows a vehicle to a complete stop and remains stationary for more than three seconds, press and release the button or press the accelerator pedal to follow the vehicle ahead.

OVERRIDING THE SET SPEED
WARNING: If you override the system by pressing the accelerator pedal, it does not automatically apply the brakes to maintain a gap from any vehicle ahead.

When you press the accelerator pedal, you override the set speed and gap distance. Use the accelerator pedal to intentionally exceed the set speed limit. When you override the system, the green indicator illuminates and the vehicle icon does not appear in the instrument cluster display.
The system resumes operation when you release the accelerator pedal. The vehicle speed decreases to the set speed, or a lower speed if following a slower vehicle.

ADAPTIVE CRUISE CONTROL INDICATORS – VEHICLES WITH: ADAPTIVE CRUISE CONTROL WITH LANE CENTERING

Illuminates when you switch lane centering on. The color of the indicator changes to indicate the system status. Gray indicates the system is on but inactive. Green indicates the system is active and applying assistance steering torque input to keep your vehicle in the center of the lane. Amber with an audible tone and then gray indicates a system auto-cancellation.

ADAPTIVE CRUISE CONTROL INDICATORS – VEHICLES WITH: ADAPTIVE CRUISE CONTROL WITH STOP-AND-GO

Illuminates when you switch the adaptive cruise control on. The color of the indicator changes to indicate the system status. White indicates the system is on but inactive. Green indicates that you set the speed and the system is active.

ADAPTIVE CRUISE CONTROL INDICATORS – VEHICLES WITH: INTELLIGENT ADAPTIVE CRUISE CONTROL

A bracket appears around the set speed and the detected speed limit sign in the information display.

System Warnings
If the set speed is increased beyond the speed limit or speed limit plus a positive tolerance value, the set speed indicator flashes.

The warning does not occur if:

• You override the set speed using the accelerator pedal.
• The vehicle speed exceeds the set speed due to being on a downhill slope.

SWITCHING FROM ADAPTIVE CRUISE CONTROL TO CRUISE CONTROL

WARNING: Normal cruise control will not brake when your vehicle is approaching slower vehicles. Always be aware of which mode you have selected and apply the brakes when necessary.

Use the touchscreen to select the following:

1. Select Settings.
2. Select Driver Assist.
3. Select Cruise Control.
4. Select Normal.

The cruise control indicator replaces the adaptive cruise control indicator if you select normal cruise control. The gap setting does not display, and the system does not respond to lead vehicles. Automatic braking remains active to maintain the set speed. The system remembers the last setting when you start your vehicle.

SWITCHING LANE CENTERING ON AND OFF

The cruise controls are on the steering wheel.

Press the button.

 

 

The indicator appears in the information display. When the system is on, the color of the indicator changes to indicate the system status.

Note: Adaptive cruise control must be on before you can switch lane centering on.

Activating Lane Centering
The system only activates when all of the following occur:

• You have adaptive cruise control with stop-and-go on.
• Your hands are on the steering wheel.
• The system detects both lane markings.

Note: If it does not detect valid lane markings, the system stays inactive until valid markings are available. You can override the system at any time by steering your vehicle.

System Alerts and Automatic Cancellation
You must keep your hands on the steering wheel at all times.
When the system is active and detects no steering activity for a certain period, the system alerts you to put your hands on the steering wheel. If you do not react to the warnings the system cancels and slows your vehicle down to idle speeds while maintaining steering control.
The system also alerts you if your vehicle crosses lane markings without detected steering activity.

Note: The system may detect a light grip or touch on the steering wheel as hands-off driving.
When an external condition cancels the system, for example, no lane markings available, a tone sounds as the icon turns amber then gray, and a message appears in the information display.

If your vehicle starts to slow down, you must provide steering input to the wheel and press and release the button to regain full system performance. Automatic cancellation can also occur if:

• The lane becomes too wide or too narrow.
• The system cannot detect valid lane markings.
• Lane markings are crossed.

Note: The system disables until the next key cycle if your vehicle slows down due to driver inactivity twice within a key cycle.

SWITCHING INTELLIGENT MODE ON AND OFF

WARNING: You are responsible for controlling your vehicle at all times. The system is designed to be an aid and does not relieve you of your responsibility to drive with due care and attention. Failure to follow this instruction could result in the loss of control of your vehicle, personal injury, or death.

1. Press Settings on the touchscreen.
2. Press Driver Assistance.
3. Press Cruise Control.
4. Press Intelligent.

Changing the Set Speed with Intelligent Adaptive Cruise Control
When intelligent mode is on, the system adjusts the set speed to the speed limit detected by the camera and the speed limit information provided by the navigation system.

Note: The set speed adjusts when the system detects a different maximum speed limit.

Note: The speed limit information provided by the navigation map data may be inaccurate or out of date. See Navigation (page 538).

Note: The system alerts you if the set speed increases beyond the speed limit. See Adaptive Cruise Control Indicators (page 310).
If the system does not detect a speed limit, the vehicle speed remains at the current set speed.
You can override the set speed at any time. You may need to override or cancel the system in certain situations such as inclement weather or if an incorrect speed is set.

Note: The system may not detect and read speed limit signs with conditional information, for example, when a sign is flashing, during specific time ranges, or when children are present.

Note: Under certain conditions, the system may not adjust the vehicle speed until after your vehicle passes the speed limit sign.\

ADJUSTING THE SET SPEED TOLERANCE – VEHICLES WITH: INTELLIGENT ADAPTIVE CRUISE CONTROL

You can set a permanent speed tolerance that is above or below the detected speed limit.

1. Press Settings on the touchscreen.
2. Press Driver Assistance.
3. Press Cruise Control.
4. Press Intelligent.
5. Press Tolerance.
6. Use + and – to set the tolerance.

Note: You cannot set the tolerance to more than 20 mph (30 km/h) above or below the recognized speed.

ADAPTIVE CRUISE CONTROL – TROUBLESHOOTING

ADAPTIVE CRUISE CONTROL –INFORMATION MESSAGES – VEHICLES WITH: ADAPTIVE CRUISE CONTROL WITH LANE-CENTERING

Note: Depending on your vehicle options and instrument cluster type, not all messages display or are available.

Note: The system could abbreviate or shorten certain messages depending on which cluster type you have.

Message	Action
Keep Hands on Steering Wheel	Return your hands to the steering wheel and provide steering input to cancel the message.
Lane Centering Assist Not Available	To reset the feature when the vehicle is stationary, return the gear selector to park and turn the engine off. Restart the engine with your foot on the brake pedal.
Resume Control	You must immediately take full control of the vehicle.
Press the Accelerator Pedal to Resume	Resume adaptive cruise control with lane centering by applying foot pressure on the accelerator pedal. You can also resume the feature by pressing the resume button on the steering wheel.

ADAPTIVE CRUISE CONTROL –INFORMATION MESSAGES – VEHICLES WITH: ADAPTIVE CRUISE CONTROL WITH STOP AND GO

Note: Depending on your vehicle options and instrument cluster type, not all messages display or are available.
Note: The system could abbreviate or shorten certain messages depending on which cluster type you have.

Message	Action
Adaptive Cruise Malfunction	A malfunction is preventing the adaptive cruise from engaging.
Front Sensor Not Aligned	Contact an authorized dealer to have the radar checked for proper coverage and operation.
Adaptive Cruise Not Available	Conditions exist preventing the system from being available.
Adaptive Cruise Not Available Sensor Blocked See Manual	You have a blocked radar because of poor radar visibility due to inclement weather or ice, mud, or water in front of the radar. You can typically clean the sensor to resolve this. Due to the nature of radar technology, it is possible to get a blockage warning with no actual block. This happens, for example, when driving in sparse rural or desert environments. A false blocked condition either self clears, or clears after you restart your vehicle.
Normal Cruise Active Adaptive Braking Off	You have selected normal cruise control. The system does not brake or react to traffic.
Adaptive Cruise – Driver Resume Control	Displays when the adaptive cruise control is going to cancel and you must take control.
Adaptive Cruise Speed Too Low to Activate	Displays when the vehicle speed is too slow to activate the adaptive cruise control and there is no lead vehicle in range.

ADAPTIVE CRUISE CONTROL –INFORMATION MESSAGES – VEHICLES WITH: INTELLIGENT ADAPTIVE CRUISE CONTROL

Note: Depending on your vehicle options and instrument cluster type, not all messages display or are available.

Note: Certain messages may be abbreviated or shortened depending on which cluster type you have.

Message	Action
Intelligent Cruise Control Speed Sign Recognition Not Available	Conditions exist preventing the system from being available.

 

FAQs

Useful Link

View Full PDF: 2022 Lincoln Corsair User Manual | Auto User Guide

2022 Lincoln Corsair Dashboard Warning and Indicator Lights Guidelines