2024 Lincoln Corsair Lighting Guide

2024 Lincoln Corsair Lighting Owner’s Manual

Lighting in the car industry is about creating the ideal atmosphere for a remarkable driving experience, not just about lighting the path ahead. This idea is elevated to a whole new level in the 2024 Lincoln Corsair thanks to its creative lighting system.

2024 LINCOLN Corsair Specs, Price, Features, Mileage and Review

Lincoln Exterior Lighting

EXTERIOR LIGHTING CONTROL

• Headlamps on.
• Autolamps on.
• Parking lamps on.
• Lamps off.

Press the toggle switch upward or downward to make a selection.

Note: The lighting control defaults to autolamps each time you switch your vehicle on.

Lincoln HEADLAMPS

USING THE HIGH BEAM HEADLAMPS

Push the lever away from you to switch the high beam on. Push the lever forward again or pull the lever toward you to switch the high beams off. Slightly pull the lever toward you and release it to flash the headlamps.

Note: Continuous activation only with headlamps on.

SWITCHING HEADLAMP EXIT DELAY ON AND OFF
To switch headlamp exit delay on, pull the turn signal lever toward you after switching your vehicle off. To switch headlamp exit delay off, pull the turn signal lever toward you again or switch your vehicle on.

Note: The headlamps turn off after three minutes with any door open or 30 seconds after the last door closes.

HEADLAMP INDICATORS

Lamps On
Illuminates when you switch the low beam headlamps or the parking lamps on.

Headlamp High Beam
Illuminates when you switch the high beam headlamps on.

 

HEADLAMPS – TROUBLESHOOTING
HEADLAMPS – FREQUENTLY ASKED QUESTIONS

Why is there condensation in the headlamps?

• Headlamps have vents to accommodate normal changes in air pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a fine mist can form on the interior of the lens. The fine mist eventually clears and exits through the vents during normal operation.

How much condensation is acceptable?

• The presence of a fine mist, for example no streaks, drip marks or large droplets. A fine mist covers less than 50% of the lens.

How long does it take for the acceptable condensation to clear?

• Clearing time can take as long as 48 hours under dry weather conditions.

How much condensation is unacceptable?

• A water puddle inside the lamp. Streaks, drip marks or large droplets present on the interior of the lens.

What should I do if unacceptable condensation is present?

• Have your vehicle checked as soon as possible.

Why do my headlamps turn off when I have them switched on when I switch my vehicle off?

• The battery saver turns the headlamps off after a short period of time after you switch your vehicle off.

Lincoln AUTOLAMPS User Manual

WHAT ARE AUTOLAMPS
WARNING: The system does not relieve you of your responsibility to drive with due care and attention. You may need to override the system if it does not turn the headlamps on in low visibility conditions, for example daytime fog.

Autolamps turn the headlamps on in low light situations or when the windshield wipers operate.

AUTOLAMP SETTINGS

1. Using the instrument cluster controls on the steering wheel, select Settings.
2. Select Vehicle.
3. Select Lighting.
4. Select Autolamp Delay.
5. Select a setting and press the OK button.

EXTERIOR LAMPS
USING THE TURN SIGNAL LAMPS

Push the lever up or down to switch the turn signal lamps on.

 

Set the lever to the middle position to switch the turn signal lamps off.

 

Note: Tap the lever up or down to make the turn signal lamps flash three times.

Turn Signal Lamp Indicator
It flashes when you switch the turn signal lamps on.

Note: An increase in the rate of flashing warns of a failed turn signal lamp.

SWITCHING THE DAYTIME RUNNING LAMPS ON AND OFF – VEHICLES WITH: CONFIGURABLE DAYTIME RUNNING LAMPS

WARNING: The daytime running lamps system does not activate the rear lamps and may not provide adequate lighting during low visibility driving conditions. Make sure you switch the headlamps on, as appropriate, during all low visibility conditions. Failure to do so may result in a crash.

• Using the instrument cluster controls on the steering wheel, select Settings.
• Select Vehicle.
• Select Lighting.
• Switch Daytime Running Lights on or off.

The daytime running lamps turn on when all of the following occur:

• You switch the system on.
• You switch your vehicle on.
• The transmission is not in park (P) for vehicles with automatic transmissions or you release the parking brake for vehicles with manual transmissions.
• The lighting control is in the autolamps position.
• The headlamps are off.

Note: Other lighting control positions do not turn on the daytime running lamps.

SWITCHING THE DAYTIME RUNNING LAMPS ON AND OFF – VEHICLES WITH: DAYTIME RUNNING LAMPS (DRL)
WARNING: The daytime running lamps system does not activate the rear lamps and may not provide adequate lighting during low visibility driving conditions. Make sure you switch the headlamps on, as appropriate, during all low visibility conditions. Failure to do so may result in a crash.

Daytime running lamps are always on unless you switch on the headlamps or your vehicle is in park (P).

SWITCHING WELCOME LIGHTING ON AND OFF
Welcome lighting turns on the exterior lamps when you approach your vehicle with an authenticated device.

• Using the instrument cluster controls on the steering wheel, select Settings.
• Select Vehicle.
• Select Lighting.
• Switch Welcome Lighting on or off.

Note: Welcome lighting still displays when you use your remote control to unlock your vehicle.

EXTERIOR LAMPS ON AUDIBLE WARNING
Sounds when you open the driver door and the exterior lamps are on.

AUTOMATIC HIGH BEAM CONTROL HOW DOES AUTOMATIC HIGH BEAM CONTROL WORK
Automatic high beam control turns the high beams on if it is dark enough and no other traffic is present. If it detects an approaching vehicle’s headlamps or tail lamps, or street lighting ahead, the system turns the high beams off. A camera sensor, centrally mounted behind the windshield of your vehicle, continuously monitors conditions to turn the high beams on and off.

• Without automatic high beam control.
• With automatic high beam control.

AUTOMATIC HIGH BEAM CONTROL PRECAUTIONS
WARNING: The system does not relieve you of your responsibility to drive with due care and attention. You may need to override the system if it does not turn the high beams on or off.

WARNING: The system may not switch the high beams off if the lights of oncoming vehicles are hidden by obstacles, for example guard rails.

WARNING: You may need to override the system when approaching other road users.

WARNING: In situations with poor visibility, such as fog, heavy rain or other inclement weather, you may need to override or completely switch off the system.

AUTOMATIC HIGH BEAM CONTROL REQUIREMENTS
The system turns the high beams on if all of the following occur:

• You switch the system on.
• You set the lighting control to the autolamps position.
• The ambient light level is low enough that you require high beams.
• There is no traffic in front of your vehicle.
• The vehicle speed is greater than approximately 25 mph (40 km/h).

AUTOMATIC HIGH BEAM CONTROL LIMITATIONS
The system turns the high beams off if any of the following occur:

• You switch the system off.
• You set the lighting control to any position except autolamps.
• The ambient light level is high enough that you do not require high beams.
• The system detects an approaching vehicle’s headlamps or a leading vehicle’s tail lamps.
• The system detects severe rain, snow or fog.
• The system detects street lighting.
• The camera has reduced visibility.
• The vehicle speed falls below approximately 19 mph (30 km/h).

Note: The deactivation speed may be lower on curves.

SWITCHING AUTOMATIC HIGH BEAM CONTROL ON AND OFF

1. Using the instrument cluster controls on the steering wheel, select Settings.
2. Select Vehicle.
3. Select Lighting.
4. Switch Auto High Beam on or off.

AUTOMATIC HIGH BEAM CONTROL INDICATORS
Illuminates to confirm when the system is ready to assist.

OVERRIDING AUTOMATIC HIGH BEAM CONTROL
Push the lever away from you to switch the high beam on. Push the lever away from you again to switch the high beams off. Push the lever away from you for a third time to switch automatic high beam control back on.

AUTOMATIC HIGH BEAM CONTROL – TROUBLESHOOTING
AUTOMATIC HIGH BEAM CONTROL – INFORMATION MESSAGES

ADAPTIVE FRONT LIGHTING (IF EQUIPPED)
HOW DOES ADAPTIVE FRONT LIGHTING WORK

WARNING: Inspect and replace the windshield wiper blades regularly to make sure the camera sensor has a clear view. The windshield wiper blades must be the correct length.

Speed Dependent Lamps (If Equipped)
Provides additional light on the road depending on your vehicle speed and steering wheel input.

• Standard low beam.
• Additional lighting.

Dynamic Bending Lamps (If Equipped)
Adapts when you are steering around a curve, the front camera detects lane markings indicating a curve or map data indicates a curve.

• Without dynamic bending lamps.
• With dynamic bending lamps.

Static Bending Lamps (If Equipped)
Illuminates the inside of a corner when you are turning the steering wheel or when you switch the turn signal lamps on.

• Headlamp beam.
• Static bending lamp beam.

Sign Based Lamps (If Equipped)
Adapts when the front camera detects certain traffic signs.

Note: The camera only detects traffic signs if your vehicle speed is below 31 mph (50 km/h).

SWITCHING ADAPTIVE FRONT LIGHTING ON AND OFF
Set the lighting control to the autolamps position to use adaptive front lighting.

Note: Other lighting control positions do not turn on adaptive front lighting.

ADAPTIVE FRONT LIGHTING – TROUBLESHOOTING (IF EQUIPPED)
ADAPTIVE FRONT LIGHTING – INFORMATION MESSAGES

Lincoln Interior Lighting

SWITCHING ALL OF THE INTERIOR LAMPS ON AND OFF
The lamps turn on under the following conditions:

• You open any door.
• You press a button on the remote control.
• You press the all lamps on button on the overhead console.

Press to switch all interior lamps on or off.

 

SWITCHING THE FRONT INTERIOR LAMPS ON AND OFF

The front interior lamp switches are on the overhead console.

Individual Map Lamps
Press the lamp lens to switch the lamps on and off.

SWITCHING THE REAR INTERIOR LAMPS ON AND OFF

The rear interior lamps may be above the rear seat or above the rear windows.

Press to switch the lamps on or off.

Note: If you switch the rear lamps on through the overhead console, you cannot switch them off with the rear lamp switch.

INTERIOR LAMP FUNCTION USER MANUAL

WHAT IS THE INTERIOR LAMP FUNCTION
The interior lamp function switches the courtesy and door lamps on or off.

SWITCHING THE INTERIOR LAMP FUNCTION ON AND OFF
Press to switch the interior lamp function on and off.

Note: The indicator lamp illuminates amber when the door function is off.

ADJUSTING THE INSTRUMENT PANEL LIGHTING BRIGHTNESS
The instrument lighting dimmer buttons are on the lighting control.

Repeatedly press one of the buttons to adjust the brightness.

 

 

AMBIENT LIGHTING
SWITCHING AMBIENT LIGHTING ON AND OFF

1. Press Settings on the touchscreen.
2. Press Vehicle Settings.
3. Press Ambient Light.
4. Press a color.

ADJUSTING AMBIENT LIGHTING
Drag the selected color up or down.

INTERIOR LIGHTING – TROUBLESHOOTING
INTERIOR LIGHTING – FREQUENTLY ASKED QUESTIONS

Why do my courtesy lamps or interior lamps turn off when I have them switched on when I switch my vehicle off?

• The battery saver turns the courtesy lamps and interior lamps off after a short period of time after you switch your vehicle off.

FAQs

Useful Links

2024 LINCOLN Corsair Specs, Price, Features, Mileage and Review

2024 Lincoln Corsair Automatic Transmission Guide

2024 Lincoln Corsair All Wheel Drive (AWD) Guide