Maserati Ghibli 2023 Punctured Tire User Manual
Introduction
The Maserati Ghibli 2023 welcomes you to the realm of luxury and performance, where class meets force on the road. But even the most amazing cars sometimes run into unforeseen problems, like a flat tire. The Maserati Ghibli 2023 will be covered in detail in this introduction, along with helpful advice on how to deal with a possible tire puncture. First off, the Maserati Ghibli 2023 combines Italian craftsmanship with cutting-edge technology to create a marvel of automotive engineering. The sleek and alluring look of this four-door luxury sports sedan instantly attracts attention everywhere it travels. Its iconic Trident logo, muscular lines, and strong grille all add to its commanding presence on the road.
Underneath the hood, the Ghibli 2023 boasts a range of powerful engine options, delivering an exhilarating driving experience. Whether you choose the V6 gasoline or the electrified hybrid powertrain, you can expect impressive performance and dynamic handling. The fusion of refined luxury and sportiness in the Ghibli creates a driving sensation that is truly unique. However, as with any vehicle, unforeseen circumstances can occur, such as a punctured tire. While it may be an inconvenience, it is essential to remain calm and follow the necessary steps to address the issue promptly. By having the right knowledge and being prepared, you can efficiently handle a punctured tire and minimize any disruptions to your journey.
Punctured Tire
If the vehicle is equipped with a compact spare wheel. Using the Compact Spare Wheel
NOTE:
The compact spare wheel is supplied in aluminium or steel: the pictures show the one in aluminium. The compact spare wheel is stored in the trunk and is supplied deflated in order to limit the amount of space occupied. An electric compressor is also provided for inflating. In the event of a tire puncture, proceed as follows.
- Stop the vehicle in a place that does not constitute a danger to traffic and where the wheel can be changed safely.
- Select the P (Park) mode and then engage manually the electric parking brake and move the ignition switch to OFF position.
- If necessary, turn the hazard warning flashers on and place the warning triangle (if equipped) at the required distance.
WARNING!
- The vehicle must be level and on firm ground during the vehicle lifting operations. The use of chock contained in the tool kit is always mandatory. In case of slight slope (less than 10%), place the chock in front of (downhill) or behind (uphill) the wheel diagonally opposite the one to be replaced. In case of higher slope (more than 10%), call the Assistance Service and avoid any operation.
- The jack should be used on level firm ground wherever possible.
- It is recommended that the wheels of the vehicle be chocked, and that no person should remain in a vehicle that is being jacked.
- Never start or run the engine with the vehicle on a jack.
- No person should place any portion of their body under a vehicle that is supported by a jack.
- Before placing the chock, it is necessary to open it like a book as shown in the picture.
- Lift the ground coverage of the trunk. Take the tools indicated in picture for changing the wheel from the container.
- Loosen and remove the spare wheel locking knob.
- Take the tool box container and the compact spare wheel out of the trunk.
Compact Spare Wheel Installation
- Using the kit wrench, loosen counterclockwise by approximately one turn the five bolts on the wheel to be changed. In case a “Wheel Security Stud Bolt” is installed, it can only be loosened and removed by using the specific fitting wrench insert provided with the “Wheel Security Stud Bolt Kit”, available in the “Genuine Accessories” range. In this case, the insert must be installed on the kit wrench.
Place the jack near the wheel to be changed as illustrated. Make sure that the head of the jack is correctly inserted in one of the slots 1 or 2 under the longitudinal member.
WARNING!
- Never position yourself under a jacked vehicle.
- A jack in the wrong position could cause the vehicle to fall. Severe risk to the operator’s safety and damage to the vehicle could occur.
- Never use the jack to carry out maintenance or repairs under the vehicle.
- Insert the kit wrench on the hexagonal end of the jack and turn it clockwise until the jack bracket is firmly inserted in the slot under the longitudinal member.
- Turn the jack lever until the wheel is raised a few inches off the ground.
- Completely unscrew the five bolts and remove the wheel.
- Make sure that the contact surfaces between spare wheel and hub are clean and free of impurities.
- Fit the compact spare wheel with the valve stem side out and secure it with the five bolts previously removed, without tightening them.
- Remove from the compressor case the inflation hose and the cable with a plug for the power outlet.
- Unscrew the valve cap of the compact spare wheel and screw the fitting of the inflation hose onto the valve.
- Insert the plug inside one of the available power outlets fitted in the trunk or passenger compartment.
- Set the ignition device on ACC or RUN position.
- Turn the compressor on by pressing the switch.
- When the pressure indicated by the gauge reaches the recommended level of 350 kPa – 51 PSI – 3.5 bar (
chapter “Tire Inflation Pressure” in section “Technical Specifications”), stop the compressor by pressing the switch again and screw the cap on the spare wheel valve.
CAUTION!
- In order to obtain a more accurate reading, the compressor should be switched off when checking the tire pressure of the compact spare wheel on the pressure gauge.
- Do not run the compressor for more than 20 minutes: there is a risk it could overheat. Also, prolonged power absorption may discharge the battery, subsequently preventing the engine from starting.
- The compressor has been designed exclusively to inflate compact spare wheels; do not use it to inflate air mattresses, floatation devices, etc.
- With the kit wrench, turn counterclockwise the hexagonal end of the jack to lower the vehicle and remove the jack.
- Fully tighten clockwise the bolts, alternately tightening diametrically opposite.
WARNING!
- FOR ALUMINIUM SPARE WHEEL Observe the tightening torque for the bolts securing the spare wheel (72 ± 7 lbf·ft/ 98 ± 10 Nm).
- FOR STEEL SPARE WHEEL Observe the tightening torque for the bolts securing the spare wheel (63 ± 7 lbf·ft/ 86 ± 10 Nm).
- To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel bolts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury.
WARNING!
- The compact spare wheel is narrower than standard wheels and must only be used to travel the distance required to reach a service station, where the punctured tire can be repaired or replaced.
- Do not exceed a maximum speed of 50 mph (80 km/h) when using the compact spare wheel; when this limit is exceeded, the stability, road holding and braking of the vehicle will be compromised. Avoid accelerating to full speed, heavy braking and fast cornering.
- The compact spare wheel must be inflated to the recommended tire pressure ( chapter “Tire Inflation Pressure” in section “Technical Specifications”).
- For safety reasons, it is absolutely forbidden to drive with more than one compact spare wheel fitted on the vehicle.
- Snow chains cannot be fitted on the compact spare wheel.
- The compact spare wheel can travel a maximum of 1,800 mi (3.000 km).
- For Trofeo Version, in case of tire/rim/valve replacement, it is necessary to use a new valve and sensor with same technical features.
To Refit the Standard Wheel with Repaired or Replaced Tire
- Following the procedure and the caution described above, raise the vehicle and remove the compact spare wheel reusing the supplied wrench.
- Fit the standard wheel with repaired or replaced tire.
- Tighten the original bolts on the wheel.
- Lower the vehicle and remove the jack.
- Fully tighten the bolts, alternately tightening diametrically opposite.
WARNING!
Observe the tightening torque for the bolts securing the wheels (72 ± 7 lbf·ft / 98 ± 10 Nm).
Once finished:
- completely deflate the compact spare wheel by pressing on the valve with the overhang of the valve cap;
- place the compact spare wheel and tool container in the boot;
- fix everything in place with the locking knob;
- Wrap the power cable and the inflation hose inside the compressor case.
- Place the compressor, the jack, the wrench and the adapter in the container inside the compact spare wheel;
- Remove the chock located in front of or behind the wheel and place it inside the container.
lower the ground coverage at the bottom of the trunk.
FAQs
- How can I tell if my Maserati Ghibli’s tire is punctured?
Possible symptoms include a rapid drop in air pressure, odd noises or sensations, or trouble steering. - What should I do if I have a punctured tire in my Maserati Ghibli?
Stop in a secure area, turn on your warning lights, and check your tire for signs of damage. You can either change the tire with a spare or ask for roadside assistance if it’s safe to do so. - Can I drive my Maserati Ghibli with a punctured tire?
Driving with a punctured tire is not advised because it may cause more harm or accidents. Call for help or use a spare tire. - How long can I drive on a spare tire in my Maserati Ghibli?
Only temporary use is intended for spare tires. The damaged tire should be replaced as soon as possible by driving to a tire repair shop. - Can a punctured tire on my Maserati Ghibli be repaired?
The size and location of the puncture are factors. Although bigger or sidewall punctures may necessitate tire replacement, smaller punctures are frequently repairable. - Where can I find the spare tire in my Maserati Ghibli?
In the Maserati Ghibli, the spare tire is typically found in the trunk, hidden by carpet or a panel. - How do I change a punctured tire on my Maserati Ghibli?
For detailed directions on changing a tire, consult the owner’s manual. Typically, a jack, lug wrench, and spare tire are required. Observe the manual’s step-by-step instructions. - What should I do after replacing a punctured tire on my Maserati Ghibli?
Make sure all lug nuts are well fastened and check the freshly installed tire’s air pressure. Consider replacing or repairing the damaged tire as soon as you can. - How much does it cost to replace a punctured tire on a Maserati Ghibli?
A number of variables, including the tire brand, size, and your location, affect the price of a new tire. For a precise price quote, it is recommended to get in touch with a nearby tire dealer or service facility. - Can I claim a punctured tire repair or replacement under warranty?
The majority of tire warranties cover manufacturing flaws, not road debris-related punctures. To find out if you qualify for coverage, consult your warranty paperwork or get in touch with your dealership. - How can I prevent tire punctures in my Maserati Ghibli?
Maintain correct tire pressure, drive cautiously to avoid hitting road debris, and routinely check your tires for wear or damage. - Are run-flat tires available for the Maserati Ghibli?
Depending on the particular model level and package, run-flat tires could be an option or a standard feature. If you want further details, speak to local car dealership. - Can I drive with a punctured run-flat tire in my Maserati Ghibli?
Run-flat tires are made to allow some driving even after a puncture, according to answer number 13. The speed and distance are constrained, though. For further information, consult your owner’s handbook. - Are punctured tires covered by car insurance?
Your insurance coverage and policy will determine this. While some insurance policies may cover tire damage, others could need additional coverage. For more information, consult your policy or get in touch with your insurance company. - Can I repair a punctured tire on my Maserati Ghibli myself?
Tire repairs need specialized equipment and knowledge. It is advised that the damage be evaluated and the required repairs be made by a qualified tire technician.
Useful Links
View Full User Guide: Maserati Ghibli 2023 User Manual | Auto User Guide
Download Manuals: On-Board Owner Documentation | Maserati