Maserati Ghibli 2023 Wiper and Washer User Manual

Introduction

The Maserati Ghibli 2023 is a luxury sports sedan known for its outstanding performance, elegant design, and cutting-edge technology. Among its many features, the Ghibli 2023’s wiper and washer system stands out as an important component for maintaining visibility and ensuring a safe driving experience in a variety of weather conditions.
The wiper and washer system in the Ghibli 2023 is designed to clean the windshield effectively, keeping it clear of rain, snow, dirt, and other debris. This system is made up of several components that work in tandem to provide dependable and efficient performance.

Along with the wiper system, the Ghibli 2023 has a washer system that works in tandem with the wipers. A fluid reservoir, pump, and spray nozzles strategically placed on the hood or windshield comprise the washer system. The washer system sprays washer fluid onto the windshield with the push of a button or control, effectively removing stubborn dirt, grime, and debris. This feature keeps the windshield clear and provides optimal visibility even in difficult conditions.

Wiper and Washer

The multifunction lever is located on the left side of the steering column. The multifunction lever operates the windshield wipers and washer when the ignition device is placed in RUN or ACC position. A windshield washer low fluid level is indicated by the warning light and by the message on the instrument cluster.

To refill the fluid, see “Maintenance Procedures” in section “Maintenance and Care”.

Windshield Wipers

• Rotate the end of the multifunction lever to one of the four settings to activate the automatic intermittent setting (see “Rain Sensing Windshield Wipers” paragraph in this chapter).
• For low speed wiper operation (stable position “LO”): rotate the end of the multifunction control lever forward to the first trigger after the intermittent setting.
• Rotate to the second trigger after the intermittent setting for high-speed
  (stable position HI) wiper operation.
  Rotate the end of the lever downward to the “MIST” position to activate a single wipe cycle. The wipers will continue to operate until you release the multifunction lever.
  The wipers will continue to operate until you release the multifunction lever.
  To turn the wipers off rotate the lever to “OFF”.
  

CAUTION!

• Turn the windshield wipers off when driving through an automatic car wash. The windshield wipers may be damaged if the wiper control is left in any position other than “OFF”.
  In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, the wiper motor may be damaged when the vehicle is restarted.
  Always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper control is turned off and the blades cannot return to the off position, the wiper motor may be damaged.

Rain Sensing Wipers
This function detects moisture on the windshield through an internal rearview mirror integrated sensor, which automatically activates the relative wipers. Rotate forward the end of the multifunction lever to one of four settings to adjust the detection system. First wiper delay position is the least sensitive, and fourth wiper delay position is the most sensitive. Third position should be used for normal rain conditions. The rain sense wipers will automatically change between an intermittent wipe, slow wipe and a fast wipe depending on the amount of detected moisture sensed by a particular area of the windshield. Place the wiper switch in the “OFF” position when you do not want to use the automatic intermittent system. The rain sensing function can be turned on and off using the MIA system, see “Functions of Settings Menu on MIA” in section “Dashboard Instruments and Controls” for further information.

• CAUTION!
• The rain sensing function may not function properly by ice or dried salt water on the windshield.
• Use on the windshield of RainX® or products containing wax or silicone may reduce rain sensor performance.

The rain sensing system has protective functions for the wiper blades and arms. It will not operate under the following conditions:

• Low temperature wipe inhibit: the rain sensing function will not operate when the ignition device is in RUN position, the vehicle is stationary and the outside temperature is below 32 °F (0 °C). To resume, set the automatic function on the multifunction lever, start the engine and drive or wait until the outside temperature rises above freezing.
• Wipe inhibit with transmission in N (Neutral) position: the rain sensing function will not operate when the ignition device is placed in the RUN position, the transmission shift lever is in the N (Neutral) position and the vehicle speed is less than 5 MPH (8 km/h). To resume, set the multifunction lever to the automatic function or move the shift lever out of N (Neutral).

Headlights On with Wipers
When activating this function, the headlights will light up approximately 10 seconds after the wipers acting on the windshield are turned on if the light switch is placed in “AUTO” position.
In addition, the headlights switch off when the wipers are turned off (position “OFF”) if they were previously turned by using this function. Powering on Headlights with wipers can be activated and deactivated with the MIA system, see “Functions of Settings Menu on MIA” in section “Dashboard Instruments and Controls” for further information.

Wiper Blade Maintenance
When the wiper arms acting on the windshield are in the rest position it is not possible to check or replace the blades (Service position) as they are folded under the hood. To service the blades (see paragraph “Wiper Maintenance and Blades Replacement” in chapter “Maintenance Procedures” of section “Maintenance and Care”) it is necessary to shift the multifunction lever to “OFF” and the ignition device to OFF position. Shift the control lever within 15 seconds to the “MIST” position (forward rotation of the end of the multifunction control lever) and release. The blades are brought in a position enabling to open the wiper arms and change the blades.

It is possible to use the “MIST” position for a maximum of 3 times within two minutes, corresponding to different three blades positions on the windshield. When completed, bring the ignition device in RUN: the arms will reposition. If necessary move the multifunction lever to other required operating positions.

WARNING!
Operate or service the windshield wiper blades without deactivating the wipers (“OFF” position), leaving the ignition device in RUN can be dangerous for the operator since the rain sensor may suddenly activate the wipers. Always use “Service” position for any intervention on the windshield wiper blades.

Windshield Washers
To use the washer, push the end of the multifunction lever inward (toward the steering column) and hold it as long as washer spray is desired . If you activate the washer while the windshield wiper control is in the automatic intermittent range, the wipers will operate for two wipe cycles after releasing the lever and then resume the previously selected intermittent interval. If you activate the washer while the windshield wiper is turned off (“OFF” position) the wipers will operate for three wipe cycles and then turn off.

WARNING!

• Do not start the windshield washer during the cold months until the windshield has warmed up. If it has not warmed up, the liquid could freeze on the glass and block your view.
• Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.

Heated Windshield Washer Nozzles 
To avoid fluid freezing inside at low external temperatures, the fluid supply nozzles can be heated by internal resistors.

Analog Clock

To adjust the analog clock located on the center of the dashboard between the air outlets, use the MIA system (see “Functions of Settings Menu on MIA” in this section).

The time can be visualized also on the MIA upper status bar and on the instrument cluster display (see “Functions of Settings Menu on MIA” in this section). Clock lighting works in the same way as instrument and controls backlighting (refer to “Interior Lighting” in section “Understanding the Vehicle”).

FAQs

1. How many wiper blades does the Maserati Ghibli 2023 have?
   The Maserati Ghibli 2023 has two wiper blades, one for the driver’s side and one for the passenger’s side.
2. Can I adjust the speed of the wipers in the Ghibli 2023?
   Yes, the Ghibli 2023 has variable-speed wipers that allow you to adjust the speed based on the intensity of the rain.
3. Are the wipers in the Ghibli 2023 rain-sensing?
   Yes, the Ghibli 2023 frequently includes rain-sensing wipers that activate automatically when rain is detected on the windshield.
4. How do I activate the washer system in the Ghibli 2023?
   To activate the washer system, the Ghibli 2023 typically has a control or button on the wiper stalk or dashboard. When you press it, it will spray washer fluid onto your windshield.
5. Can I adjust the frequency of the intermittent wiper settings?
   Yes, the Ghibli 2023’s intermittent wiper settings are adjustable, allowing you to customize the frequency of wipes to your liking.
6. Where is the washer fluid reservoir located in the Ghibli 2023?
   The washer fluid reservoir in the Ghibli 2023 is usually found under the hood.
7. How often should I refill the washer fluid in the Ghibli 2023?
   The frequency with which the washer fluid must be replaced is determined by usage and weather conditions. It is recommended that you check the fluid level on a regular basis and refill as needed.
8. Can I use any washer fluid in the Ghibli 2023?
   It is generally recommended to use a washer fluid designed specifically for automotive use. For recommended washer fluid types, consult the vehicle’s owner’s manual or a Maserati dealer.
9. Do the wiper blades in the Ghibli 2023 need regular replacement?
   Wiper blades do wear out over time and must be replaced on a regular basis to maintain effective performance. When the blades show signs of deterioration, they should be inspected and replaced.
10. Are the wiper blades in the Ghibli 2023 easy to replace?
    While specific instructions may vary, replacing wiper blades in the Ghibli 2023 is a simple process in general. For proper replacement procedures, refer to the vehicle’s owner’s manual or consult a Maserati dealer.
11. Can I use the wipers and washer system while the Ghibli 2023 is parked?
    Yes, the wipers and washer system in the Ghibli 2023 can be operated while the vehicle is parked. However, it is best to use them sparingly to avoid excessive wear on the wiper blades.
12. Are there any special maintenance requirements for the wiper and washer system in the Ghibli 2023?
    The wiper and washer system in the Ghibli 2023 requires regular maintenance, which includes inspecting the blades, cleaning the washer nozzles, and ensuring proper fluid levels. For detailed maintenance instructions, consult the vehicle’s owner’s manual.
13. Can the Ghibli 2023 wipers handle heavy rain or snow?
    The Ghibli 2023’s wiper blades are designed to withstand typical rain conditions. However, driving in heavy rain or snow may necessitate slower speeds and extra caution for optimal visibility.

Useful Links

View Full User Guide: Maserati Ghibli 2023 User Manual | Auto User Guide
Download Manuals: On-Board Owner Documentation | Maserati