Maserati Levante 2023 Blind Spot Assist User Manual
Introduction
Luxury, performance, and style have always been associated with Maserati, and the newest model to join their illustrious range, the Maserati Levante 2023, elevates these characteristics to a whole new level. The Levante 2023 is a genuine representation of Italian automotive brilliance with its beautiful design, strong engine options, and cutting-edge technology. The cutting-edge Active Driving Assist technology, which raises the driving experience to previously unheard-of levels of convenience, safety, and enjoyment, is one distinguishing feature that makes this SUV stand out. Maserati’s cutting-edge suite of driving aid technologies, known as Active Driving Assist, was created to add an extra degree of security and assurance when driving.
It creates a comprehensive driving assistance system that functions flawlessly with the driver, improving both safety and comfort. It integrates the newest sensors, cameras, and sophisticated algorithms. Adaptive cruise control, one of the essential elements of Active Driving Assist, uses radar and video sensors to keep a safe distance from the car in front of it. This feature not only frees the driver from having to constantly adjust the speed but also makes for a smoother, more enjoyable drive, especially in situations where there is a lot of traffic or distance to cover.
Blind Spot Assist
System Operation
The Blind Spot Assist (BSA) system uses two radar-based sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (cars, buses, motorbikes, etc.) that enter the blind spot zones from the rear/front/side of the vehicle in adjacent lanes. The example shown in the figure highlights the blind spots on either side of the vehicle when oncoming traffic is approaching from behind.
When the vehicle is started, the BSA warning light will momentarily illuminate in both outside rear view mirrors to let the driver know that the system is operational and on. The BSA system sensors operate when the vehicle is in any forward gear and enters standby mode when the transmission is in (P) Park.
The BSA detection zone shown in figure covers approximately one lane on both sides of the vehicle (approximately 11 ft or 3.3 m). The blind spot area extends from immediately behind the exterior rearview mirrors up to about 23 ft (7 m) behind the rear bumper.
The BSA system monitors the detection zones on both sides of the vehicle to detect the presence of vehicles and begins to warn the driver by flashing the warning light in the external side mirror when the vehicle speed reaches approximately 4 MPH (6 km/h) or higher.
WARNING!
- The Blind Spot Assist (BSA) system does NOT alert the driver about rapidly approaching vehicles that are outside the detection zones.
- The BSA might alert the driver too late especially in case of rapidly approaching vehicles.
- The driver must always pay utmost attention and drive carefully.
WARNING!
Risk of accident despite Blind Spot Assist (BSA). BSA does not detect/react to the following:
- Overtaking vehicles close on the side, placing them in the blind spot area. As a result, BSA may neither give warnings nor intervene in such situations.
- Always pay attention to the traffic situation and maintain a safe distance at the side of the vehicle.
NOTE:
If your vehicle has experienced any damage in the area where the sensor is located, even if the fascia is not damaged, the sensor may have become misaligned. Take your vehicle at an Authorized Maserati Dealer to verify sensor alignment. Having a sensor that is misaligned will result in the BSA not operating to specification. The area on the rear bumper fascia where the radar sensors are located must remain free of snow, ice, and dirt/road contamination so that the BSA system can function properly. Do not cover or block the area of the rear bumper fascia where the radar sensors are located with foreign objects (bumper stickers, spoilers, bicycle racks, etc.). The BSA system notifies the driver of vehicles or objects in the detection zones by illuminating the BSA warning light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume
(if the radio is on). Refer to “BSA and RCP Setting” in this chapter for further information. The BSA system monitors the detection zone from three different entry points (side, rear, overtaking traffic) while driving to see if an alert is necessary. The BSA system will issue an alert whenever a vehicle enters any one detection zone as outlined below.
Speed Range of Use
| Speed | MPH (km/h) |
| Minimum | 6 (10) |
| Engaged/activated | 6 (10) |
| Maximum | – (–) |
Entering from the Side
Vehicles that move into your adjacent lanes from either side of the vehicle.
Entering from the Rear
The alert will turn on when the vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of more than 27 MPH (43 km/h).
Entering from the Rear
The alert will turn on when the vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of more than 27 MPH (43 km/h).
Overtaking Traffic
The figures show the vehicle approaching (A) and passing (O) another vehicle in the overtaking lane. If you pass another vehicle slowly, the vehicle remains in the blind spot for approximately 2 seconds, the BSA warning light in the outside mirror will illuminate after 1.5 seconds. If the difference in speed between the two vehicles is greater, the warning light will not illuminate.
Other Cases
The BSA system is not designed to issue an alert on stationary objects such as guardrails, posts, walls, foliage heaps, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service.
The BSA system will not alert you of objects that are travelling in the opposite direction of the vehicle in adjacent lanes.
WARNING!
- The Blind Spot Assist (BSA) system is only an aid to help detect vehicles in the blind spot zones.
- The BSA system is not designed to detect pedestrians, cyclists, or animals.
- Even if your vehicle is equipped with the BSA system, always check your vehicle’s outside and rearview mirrors for any vehicles approaching from behind or overtaking.
- Use your turn signal before changing lanes.
System Monitoring on TFT Display
Whenever the BSA system is enabled by the user, an specific indicator is displayed in the left upper corner of the TFT display (area 22). This indicator can take on different colors depending on the system status:
stand by status (white icon);
active status (green icon).
RCP – Rear Cross Path
The Rear Cross Path (RCP) function is intended to aid the drivers when gear in reverse of parking spaces where their vision of oncoming vehicles may be blocked. The RCP system monitors the rear detection zones on both sides of the vehicle. Using sensors located on either side of the rear bumper, it detects vehicles or objects that are moving toward the side of the vehicle with a minimum speed of approximately 1 to 2 MPH (1 km/h to 3 km/h) to a maximum of approximately 10 MPH (16 km/h), such as in parking lot situations.
NOTE:
In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. Proceed slowly and cautiously out of the parking space until the rear end of the vehicle is moderately exposed. The RCP system will then have a clear view of the cross traffic. If an oncoming vehicle is detected, the RCP system will alert the driver using both the visual and audible alarms. If the radio is on, it will also reduce the radio volume.
WARNING!
Rear Cross Path (RCP) is not a Back Up Aid system. More specifically, it is intended to be used to help a driver detect an oncoming vehicle in a parking lot situation. Drivers must be careful when backing up, even when using RCP. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. Failure to do so can result in serious injury or death.
BSA and RCP Setting
Setting modes can be selected from the MIA system. Touch “Settings” soft-key on “Vehicle” page and then select “Blind Spot Assist” soft-key to enter the setting page. Refer to chapter “Functions of Controls Menu on MIA” in section “Dashboard Instruments and Controls” for further information.
BSA in Visual Mode
When operating in “Visual” mode, the BSA system will provide a visual alert in the appropriate side view mirror when it detects a vehicle or an object in the detection areas monitored by its sensors: depending on the status of the relative turn indicator, the warning light can be fixed or flashing. However, when the system is operating in RCP mode, it will respond with both visual and audible alerts when an oncoming vehicle or an object approaching the rear end side of the vehicle is detected. Whenever an audible alert is requested, the radio is muted (if the radio is on). BSA in Visual and Acoustic Mode When operating in “Visual & Acoustic” mode, the BSA system will provide a visual alert in the appropriate side view mirror based on a detected vehicle or object. If the turn signal is then activated, and it corresponds to an alert present on that side of the vehicle, an audible chime will also be sounded: in the same moment the warning light will start flashing. Whenever a turn signal and detected vehicle or object are present on the same side at the same time, both the visual and audio alerts will be issued. In addition to the audible alert, the radio volume will be reduced (if the radio is on).
NOTE:
If the hazard flashers are on, the BSA system will issue the appropriate visual alert only. When the system is in RCP mode, the system shall respond with both visual and audible alerts when a detected vehicle or object is present. Whenever an audible alert is requested, the radio (if on) is also muted. Right/left turn/hazard signal status is ignored; the RCP status always requests the chime when needed.
Blind Spot Alert Off
When this function is turned off from the MIA, there will be no visual or audible alerts from either the BSA or RCP subsystems.
NOTE:
The BSA system will store the current operating mode when the vehicle is shut off. Each time the vehicle is started, the previously-stored mode will be recalled and used.
System Temporarily Unavailable
The blind spot system will become temporarily unavailable and the instrument cluster display will show the message “Blind Spot Alert Temporarily Unavailable” when the vehicle enters a radio quiet zone (example the areas around radio telescopes). The warning light on the outside rearview mirrors will be lit up and stay lit until the vehicle exits the zone.
System is Faulty
The BSA system cannot properly operate due to a fault of its components, or because the area on the rear bumper fascia where the radar sensors are located is dirty. In these cases the amber warning light and the related message will be displayed on the instrument cluster.
In these cases do not use the system and have the vehicle inspected at an Authorized Maserati Dealer.
Radar Device – Regulatory Information
The “Regulatory Information” for all the radio frequency and radar devices can be consulted by accessing the “Services” section on the website www.maserati.com.
FAQs
The Maserati Levante 2023 has a safety technology called Blind Spot Assist that assists in identifying objects in the driver’s blind areas.It monitors the spaces next to and behind the car with sensors or cameras and notifies the driver when a car is in the blind spot.
Depending on the individual implementation, the actual functioning mechanism may vary, but generally speaking, Blind Spot Assist in the Maserati Levante 2023 monitors the blind spot areas using sensors or cameras positioned on the exterior of the car. The system will often issue a visual or audio alert to notify the driver if a vehicle is found in the blind spot while the driver is attempting to change lanes or perform a maneuver.
Blind Spot Assist helps drivers by alerting them to the presence of vehicles in their blind zones. While warning the driver of potential hazards can greatly increase safety, it is ultimately up to the driver to take the proper precautions. Before changing lanes or performing maneuvers, the driver must always visually check their blind areas and use their mirrors.
The Maserati Levante 2023’s trim level and particular configuration may affect whether Blind Spot Assist is offered as a standard or optional feature. The most accurate and current information regarding feature availability should be obtained from the official Maserati website or by contacting a Maserati dealership.
In general, regular weather and road conditions should be compatible with the Maserati Levante 2023’s Blind Spot Assist. Extreme weather, such as persistent rain, snow, or fog, may, however, impair the system’s functionality or accuracy. Driving in difficult situations requires constant caution and reliance on your own visual inspections.
Depending on the system’s capabilities and design, the Maserati Levante 2023’s Blind Spot Assist may or may not be able to detect motorbikes and bicycles. Some systems can identify not only cars but also motorbikes and bicycles, which are smaller vehicles. For more information about the Levante 2023’s Blind Spot Assist system, it is advised to refer to the owner’s manual or contact a Maserati dealership.
The majority of contemporary cars with Blind Spot Assist, like the Maserati Levante 2023, give the driver the option to turn the system on or off as they see fit. The precise procedure to activate or deactivate the Blind Spot Assist feature may differ, so it is advised to refer to the owner’s manual or get help from a Maserati dealership.
No, utilizing mirrors while driving is still necessary, even with Blind Spot Assist. It helps drivers identify vehicles in their blind areas as an added safety element. Even when Blind Spot Assist is engaged, it is still imperative to visually scan the blind spots using the side and rearview mirrors before changing lanes or performing maneuvers.
The Maser has Blind Spot Assist, yes.
The Maserati Levante 2023’s Blind Spot Assist primarily focuses on spotting vehicles in the blind spot areas. Although the system may have a variety of capabilities, it is generally made to detect moving items, like vehicles, rather than stationary objects like individuals. There may be a supplementary charge for additional safety features like collision avoidance systems or pedestrian detection.
No, using turn signals and using safe driving practices are not substituted by Blind Spot Assist. Maintaining excellent driving practices is essential, including checking your blind areas, using your mirrors, and indicating effectively while changing lanes or performing maneuvers. Although Blind Spot Assist is meant to be an additional tool to improve safety, the driver’s duty and alertness are of utmost importance.
It might not be possible or might require extensive alterations and adjustments to retrofit or install Blind Spot Assist to older Maserati Levante cars. During manufacture, automotive safety measures are often included into the design and electronics of the car. It is advised to speak with a Maserati dealership or a licensed automotive technician to find out if Blind Spot Assist may be installed to an older Levante model.
Useful Links
View Full User Guide: Maserati Levante 2023 User Manual | Auto User Guide
Download Manuals: On-Board Owner Documentation | Maserati
2023 Maserati Levante Specs, Price, Features, Mileage (Brochure)
Related Articles:
2023 Maserati GRECALE Specs, Price, Features, Mileage (Brochure)
2023 Maserati Granturismo Specs, Price, Features, Mileage (Brochure)
2023 Maserati Ghibli Specs, Price, Features, Mileage (Brochure)
2023 Maserati Quattroporte Specs, Price, Features, Mileage (Brochure)
