2020 Mitsubishi ASX Display Instrument Cluster | How to use

2020 Mitsubishi ASX Display Instrument Cluster | How to use

The LCD instrument cluster of the 2020 Mitsubishi ASX greets drivers with ease and modernity. The cluster, which is situated right behind the steering wheel, has a modern and well-organized digital display that makes important information quickly accessible. In order to provide a connected and knowledgeable driving experience, this innovative cluster delivers a multitude of data, such as vehicle speed, fuel efficiency, trip information, and navigation instructions. With its lively graphics and simple interface, the 2020 ASX is a well-rounded and easy-to-use car that makes for a fun and educational ride.

2023 Mitsubishi ASX Specs, Price, Features, Mileage (Brochure)

Instruments

1.  Tachometer ®
2. Multi-information display ®
3. Information screen display list
4. Speedometer (km/h or mph + km/h)
5. Daytime dipper button (meter illumination control) ®

Tachometer
The tachometer indicates the engine speed (r/min). The tachometer helps you to obtain more economical driving and also warns you of excessive engine speeds (Red zone).

CAUTION

• When driving, watch the tachometer to make sure that the engine speed indication does not rise into the red zone (excessive engine rpm).

Daytime dipper button (meter illumination control)
Each time you press this button, there is a sound and the brightness of the instruments changes.

NOTE

• You can adjust to 8 different levels for when the position lamps are illuminated and 8 for when they are not.
• The meter illumination switches automati-cally to the adjusted brightness, depending on the brightness outside the vehicle.
• The brightness level of the instruments is stored when the ignition switch is turned to the “LOCK” position or the operation mode is put in OFF.
• If you press and hold the button for longer than approximately 1 second when the position lamps are illuminated, the brightness level changes to the maximum level. Pressing and holding the button for longer than approximately 1 second again returns the brightness level to the previous level. On vehicles equipped with the Smartphone-link Display Audio (SDA) or the Smart-phone-link Display Audio (SDA) navigation system, the following conditions may occur when the meter illumination brightness level is at the maximum.
   
• The screen colour does not switch to the nighttime setting.
• The switch brightness does not illuminate.

1. Brightness display
2. Rheostat illumination button

Multi-information display

Always stop the vehicle in a safe place before operating. The following information is included on the multi-information display: warnings, odometer, trip meter, service reminder, engine coolant temperature, fuel remaining, outside temperature, selector lever position, 4WD operation status, average and momentary fuel consumption, driving range, average speed and meter illumination. It is also possible to change elements such as the language and units used on the multi-information display.

1. mark display screen (when the ignition switch or the operation mode is OFF)
2. Information screen (when the ignition switch or the operation mode is OFF)
3. Interrupt display screen (when the ignition switch or the operation mode is OFF)
4. Door ajar warning display screen (when the ignition switch or the operation mode is OFF)
5. Odometer
6. Drive mode indicator display screen*
7. mark display screen (when the ignition switch or the operation mode is ON) ®
8. Lane Departure Warning (LDW) display screen* ®
9. Blind Spot Warning (BSW) display screen* ®
10. ECO indicator* ®
11. Information screen (when the ignition switch or the operation mode is ON) ®
12. Interrupt display screen (when the ignition switch or the operation mode is ON) ®
13. Fuel remaining display screen
14. Outside temperature display screen ®
15. Auto Stop & Go (AS&G) display screen* ®
16. Auto Stop & Go (AS&G) OFF display screen* ®
17. Engine coolant temperature display ®
18. Gearshift indicator display screen* ®
19. Selector lever position display screen* ®

NOTE

• The fuel units, temperature units, display language, and other settings can be changed.
• The display screen is different depending on whether the ignition switch or the operation mode is OFF or ON.

Multi-information meter switch
Each time the multi-information meter switch is operated, a sound is emitted and the multi-information display changes between information such as warnings, trip meter, service reminder, average and momentary fuel con-sumption, driving range, and average speed. It is also possible to change elements such as the language and units used on the multi-information display by operating the multi-information meter switch.

mark display screen (when the ignition switch or the operation mode is OFF)
If you press the multi-infor-mation meter switch and return from the warning display screen to the previous screen, the mark is displayed. Refer to “To return to the screen displayed before the warning display” on page 5-07. This mark is also displayed if there is another warning other than the one displayed. When the cause of the warning display is eliminated, the mark goes out automatically.

NOTE
When the mark is displayed, the warning display screen can be redisplayed on the information screen.

Information screen (when the ignition switch or the operation mode is OFF)
Each time you lightly press the multi-infor-mation meter switch, the display screen switches in the following order.

1. When there is no warning display
2. When there is a warning display
   1. Tripmeter A
   2. Tripmeter B
   3. Service reminder
   4. Redisplay of a warning display screen

Odometer/Tripmeter

Odometer
The odometer indicates the distance travelled.

Tripmeter
The trip meter indicates the distance travelled between two points. Example usage of trip meter and trip meter It is possible to measure two currently travelled distances, from home using a trip meter and from a particular point on the way using a trip meter.

To reset the trip meter
To return the display to 0, hold down the multi-information meter switch for approxi-mately 2 seconds or more. Only the currently displayed value will be reset. If the trip meter is displayed, only trip meter will be reset.

Service reminder
This displays the distance and number of months until the next periodic inspection.

Interrupt display screen (when the ignition switch or the operation mode is OFF)
When there is information to be announced, such as lamp reminders, the buzzer sounds and the multi-information display switches to the warning display screen. Refer to the appropriate page and take the necessary measures. When the cause of the warning display is eliminated, the warning display goes out au-tomatically.

1. Information generated
2. Cause eliminated

To return to the screen displayed before the warning display
Even if the cause of the warning display is not eliminated, you can return to the screen that was displayed before the warning display. If you press the multi-information meter switch, the display screen switches to the screen that was displayed before the warning display and the mark (A) is displayed.

Redisplay of a warning display screen
When the mark is displayed, if you lightly press the multi-information meter switch a few times, the warning display screen you switched from is displayed again.

Door ajar warning display screen (when the ignition switch or the operation mode is OFF)
If any of the doors or the tailgate is not completely closed, this displays the open door or tailgate.

1. Doors and tailgate are closed
2. Doors or tailgates are open

Information screen (when the ignition switch is turned from the “LOCK” position to the “ON” position or the operation mode is changed from OFF to ON)
When the ignition switch is turned to the “ON” position or the operation mode is put in ON, the display screen switches in the following order.

1. Screen when the ignition switch or the operation mode is OFF
2. System check screen
3. Screen when the ignition switch or the operation mode is ON

System check screen
When the ignition switch is turned to the “ON” position or the operation mode is put in ON, the system check screen is displayed for approximately 4 seconds. If there is no fault, the information screen (when the ignition switch or the operation mode is ON) is displayed. If there is a fault, the screen changes to a warning display.

NOTE

• The system check screen display varies depending on the customer’s equipment.

Service reminder
When the time for periodic inspection arrives, the warning display is displayed for a few seconds after the ignition switch or the operation mode ON screen.

Drive mode indicator display screen*
This displays the 4WD status. If you select “4WD LOCK” mode with the drive mode selector, “4WD LOCK” is displayed; if you select “4WD AUTO” mode, “4WD” is displayed. Nothing is displayed when 2WD mode is selected.

mark display screen (when the ignition switch or the operation mode is ON)
This is displayed when you press the multi-information meter switch and switch the warning display screen. This mark is also displayed if there is another warning other than the one displayed. When the cause of the warning display is eliminated, the mark goes out automatically.

NOTE
When the mark is displayed, the warning display screen can be redisplayed on the information screen.

Information screen (when the ignition switch or the operation mode is ON)
Each time you lightly press the multi-infor-mation meter switch, the display screen switches in the following order.

1. Tripmeter A
2. Tripmeter B
3. Service reminder
4. Driving range display, momentary fuel consumption display
5. Average fuel consumption display, momentary fuel consumption display
6. Average speed display, momentary fuel consumption display
7. Function setting screen
8. Redisplay of a warning display screen

• While driving, even if you operate the multi-information meter switch, the function setting screen is not displayed. Always stop the vehicle in a safe place before operating.
• When there is information to be announced, such as a system fault, the buzzer sounds and the screen display is switched.

Odometer/Tripmeter
The operation method is the same as when the ignition switch or the operation mode is OFF.

Service reminder
This displays the distance and number of months until the next periodic inspection.

Engine coolant temperature display
This indicates the engine coolant temperature. If the coolant becomes hot, “ ” will blink. Pay careful attention to the engine coolant temperature display while you are driving.

CAUTION

• If the engine is overheating, “ ” will blink. In this case, the bar graph is on the red zone. immediately park the vehicle in a safe place and take the required measures.

2023 Mitsubishi ASX Specs, Price, Features, Mileage (Brochure)

Driving range display
This displays the approximate driving range (how many more kilometres or miles you can drive). When the driving range falls below approximately 50 km (30 miles), “—” is displayed. Refuel as soon as possible.

NOTE

• The driving range is determined based on the fuel consumption data. This may vary depending on the driving conditions and habits. Treat the distance displayed as just a rough guideline.
• When you refuel, the driving range display is updated.
  However, if you only add a small amount of fuel, the correct value will not be displayed. Fill with a full tank whenever possible.
• On rare occasions, the value displayed for the driving range may change if you are parked on an extremely steep incline. This is due to the movement of fuel in the tank and does not indicate a malfunction.
• The display setting can be changed to the preferred units (km or miles)

Average speed display
This displays the average speed from the last reset to the present time. There are the following 2 mode settings.

Manual reset mode

• When the average speed is being displayed, if you hold down the multi-infor-mation meter switch, the average speed displayed at that time is reset.
• When the following operation is performed, the mode setting is automatically switched from manual to auto.
• [Except for vehicles equipped with key-less operation system]
• Turn the ignition switch from the “ACC” or “LOCK” position to the “ON” position.
• [For vehicles equipped with keyless operation system]
• Change the operation mode from ACC or OFF to ON.
• Switching to auto occurs automatically. If switching to manual mode is done, however, the data from the last reset is displayed.

Auto reset mode

• When the average speed is being dis-played, if you hold down the multi-infor-mation meter switch, the average speed displayed at that time is reset.
• When the engine switch or the operation mode is in the following conditions, the average speed display is automatically reset.
• [Except for vehicles equipped with key-less operation system]
• The ignition switch is in the “ACC” or “LOCK” position for approximately 4 hours or longer.
• [For vehicles equipped with keyless operation system]
• The operation mode is in ACC or OFF for approximately 4 hours or longer.

NOTE

• The average speed display and the average fuel consumption display can be reset individually for the auto reset mode and manual reset mode.
• “—” is displayed when the average speed cannot be measured.
• The initial (default) setting is “Auto reset mode”.
• The display setting can be changed to the preferred units (km/h or mph).
• The memory of the auto reset mode or manual reset mode for the average speed display is erased if the battery is disconnected.

Average fuel consumption display
This displays the average fuel consumption from the last reset to the present time. There are the following 2 mode settings.

The “ ” mark (A) in the momentary fuel gauge shows the average fuel consumption.

Manual reset mode

• When the average fuel consumption is being displayed, if you hold down the multi-information meter switch, the average fuel consumption displayed at that time is reset.
• When the following operation is performed, the mode setting is automatically switched from manual to auto.
• [Except vehicles equipped with keyless operation system]
• Turn the ignition switch from the “ACC” or “LOCK” position to the “ON” position.
• [For vehicles equipped with keyless operation system]
• Change the operation mode from ACC or OFF to ON.
• Switching to auto occurs automatically. If switching to manual mode is done, however, the data from the last reset is displayed.

Auto reset mode

• When the average fuel consumption is displayed, if you hold down the multi-information meter switch, the average fuel consumption displayed at that time is reset.
• When the engine switch or the operation mode is in the following conditions, the average fuel consumption display is au-tomatically reset.
• [Except for vehicles equipped with key-less operation system]
• The ignition switch is in the “ACC” or “LOCK” position for approximately 4 hours or longer.
• [For vehicles equipped with keyless op-eration system]
• The operation mode is in ACC or OFF for approximately 4 hours or longer.

NOTE

• The average speed display and the average fuel consumption display can be reset individually for the auto reset mode and manual reset mode.
• “—” is displayed when the average fuel con-sumption cannot be measured.
• The initial (default) setting is “Auto reset mode”.
• The average fuel consumption depends on the driving condition (road condition, driv-ing behaviour, etc.). The displayed fuel con-sumption may vary from the actual fuel con-sumption. Treat the fuel consumption displayed as just a rough guideline.

  The memory of the auto reset mode or manual reset mode for the average fuel con-sumption display is erased if the battery is disconnected.

• The display setting can be changed to the preferred units {km/L, mpg (US), mpg (UK) or L/100 km}.

Momentary fuel consumption display
While driving, this displays the momentary fuel consumption, using a bar graph.

When the value of momentary fuel consumption surpasses the value of average fuel con-sumption, the momentary fuel consumption is displayed with a white bar graph. Be conscious of maintaining the value of monthly fuel consumption below the value of average fuel consumption, driving with better fuel consumption can be possible.

NOTE

• When the momentary fuel consumption cannot be measured, the bar graph is not displayed.
• The display setting can be changed to the preferred units {km/L, mpg (US), mpg (UK) or L/100 km}.
• It is possible to cancel the green bar graph.

Function setting screen
The “Display language”, “Temperature unit”, “Fuel consumption unit”, and “Average fuel consumption and speed reset method” etc. settings can be modified as desired.

Interrupt display screen (when the ignition switch or the operating mode is ON)

Warning display
When there is information to be announced, such as a system fault, a sound is emitted and the information screen switches to the warning display screen. When the cause of the warning display is eliminated, the warning display goes out au-tomatically.

To return to the screen displayed before the warning display
Even if the cause of the warning display is not eliminated, you can return to the screen that was displayed before the warning display. If you press the multi-information meter switch, the display screen switches to the screen that was displayed before the warning display and the mark (A) is displayed.

Redisplay of a warning display screen
When the mark is displayed, if you lightly press the multi-information meter switch a few times, the warning display screen you switched from is displayed again.

Other interrupt displays
The operation status of each system is displayed on the information screen.

Selector lever position display screen*
Shows the position of the selector lever.

Outside temperature display screen
This shows the temperature outside the vehicle.

NOTE
The display setting can be changed to the preferred units (°C or °F).

FAQs

Useful Link

View Full PDF: 2020 Mitsubishi ASX Owner’s Manual

2023 Mitsubishi ASX Specs, Price, Features, Mileage (Brochure)

2020 Mitsubishi ASX Fuses and Fuse Box | Replacing a blown fuse