2023 Mitsubishi Eclipse Cross Instrument Cluster

The 2023 Mitsubishi Eclipse Cross has a high-tech instrument cluster that can be changed in many ways. This is the pinnacle of current car technology. The digital display, which is usually 7 inches or bigger and has a sleek and ergonomic design, puts a lot of important information, like speed, fuel level, engine temperature, and vehicle status, right at the driver’s fingertips. This high-tech instrument cluster goes beyond the basics. It works seamlessly with Apple CarPlay and Android Auto, so drivers can stay linked and use their favorite apps and navigation right from the cluster. Also, the instrument panel of the 2023 Eclipse Cross has features to help the driver, shows real-time navigation directions, and even has eco-driving indicators to encourage driving in a way that saves gas. With its flexibility, user-friendly interface, and ability to be customized, the instrument cluster in the 2023 Mitsubishi Eclipse Cross takes driving to a whole new level while keeping drivers updated and connected on the road.

Instrument cluster

1. Tachometer
2. Multi-information display
   • Information screen display list
3. Speedometer
4. Rheostat illumination button

Speedometer

• The speedometer shows the vehicle speed in miles per hour (mph) or kilometers per hour (km/h).

Tachometer

• The tachometer shows engine revolutions per minute. This allows the driver to determine the most efficient selector position and engine speed combinations.
• This gauge also assists in evaluating engine performance.

CAUTION: The red zone indicates an engine speed beyond the range of safe operation. Select the correct selector position to control the engine speed so that the tachometer indicator does not enter the red zone.

Meter illumination control

Each time you press this button, there is a sound and the brightness of the instruments changes.

1. Brightness level
2. Rheostat illumination button

NOTE

• You can adjust to 8 different levels for when the front side marker lights are illuminated and when they are not.
• If the vehicle is equipped with the automatic light control, the light switch is in the “ ”, “ ”, or “AUTO” position and it is sufficiently dark outside the vehicle, the meter illumination switches automatically to the adjusted brightness.
• The brightness level of the instruments is stored when the ignition switch is turned to the “OFF” position or the operation mode is put in OFF.
• If you press and hold the button for longer than approximately 2 second when the front side-marker lights are illuminated, the brightness level changes to the maximum level. Pressing and holding the button for longer than approximately 2 second again returns the brightness level to the previous level. It is recommended to use this function when it is difficult to read the meter due to the meter illumination is dimmed by turning on the tail lights in bright areas. For vehicles equipped with the Smartphone link Display Audio (SDA) or the Smartphone- link Display Audio (SDA) navigation system, the operation of the screen background theme and the switch illumination, when the meter illumination brightness level is changed to the maximum, vary depending on the specifications of the SDA or the SDA navigation system.

Multi-information display

The multi-information display displays warnings, the odometer, trip odometer, service reminder, engine coolant temperature, fuel remaining, outside temperature, selector lever position, average and instant fuel consumption, driving range, average speed, etc. It is also possible to change elements such as the language and units used on the multi-information display.

[With the ignition switch or the operation mode in OFF]

1. Warning display screen
2. Information screen  Interrupt display screen
3. Door ajar warning display screen
4. Odometer
5. “ ” mark indicator

[With the ignition switch or the operation mode in ON]

1. S-AWC drive mode display screen (if so equipped)
2. Warning display screen
3. ECO mode indicator display screen
4. Information screen
5. Selector lever position display
6. Engine coolant temperature display
7. Odometer
8. Cruise control display screen
9. Adaptive Cruise Control System (ACC) display screen (if so equipped)
10. ECO indicator
11. “ ” mark indicator
12. Fuel remaining display screen
13. Outside temperature display screen

NOTE

• The fuel units, outside temperature units, display language, and other settings can be changed.
• Refer to “Changing the function settings”

Multi-information display switches

Each time the multi-information display switches are operated, the buzzer sounds and the multi-information display changes between information such as warnings, trip odometer, average and instant fuel consumption, and distance range. It is also possible to change elements such as the language and units used on the multi-information display by operating the multi-information display switches.

Information screen (With the ignition switch in “OFF” position or the operation mode in OFF)

Press the switch to display the information screen. Then, press the switch or switch to switch the display screen in the following order.

*: When there is a warning display

1. Trip odometer A
2. Trip odometer B
3. ECO score display
4. Service reminder
5. Redisplay of a warning display screen

Information screen (With the ignition switch is turned from the “OFF” position to the “ON” position or the operation mode is changed from OFF to ON)

When the ignition switch is turned to the “ON” position or the operation mode is put in ON, the display screen switches in the following order.

*: When the inspection time has arrived

1. Screen when the ignition switch or the operation mode is OFF
2. System check screen
3. Screen when the ignition switch or the operation mode is ON
4. Service reminder

Information screen (With the ignition switch or the operation mode in ON)

Press the switch or switch to switch the display screen in the following order.

*: When there is a warning display

1. Trip odometer
2. Trip odometer A
3. Driving range display B
   • ECO drive assist display
4. Average fuel consumption display
   • ECO drive assist display
5. Average speed display
   • Instant fuel consumption display
6. ECO score display
7. AYC (Active Yaw Control) operation display (if so equipped)
8. S-AWC operation display (if so equipped)
9. Service reminder
10. Function setting screen
11. Redisplay of a warning display screen

NOTE

• While driving, the service reminder are not displayed even if you operate the multiinformation display switches. Always stop the vehicle in a safe place before operating.
• While driving, the function setting screen is not displayed even if you operate the multi-information display switches. Always park the vehicle in a safe place, firmly apply the parking brake and put the selector lever into the “P” (PARK) position before operating the function setting screen. Refer to “Changing the function settings”.
• When there is information to be announced, such as a system fault, the tone sounds and the screen display is switched. Refer to “Interrupt display screen”

Interrupt display screen

Warning display

When there is information to be announced, such as a system fault, the tone sounds and the information screen is switched to the warning display screen. Refer to the warning list and take the necessary measures. When the cause of the warning display is eliminated, the warning display goes out automatically.

Returning to the display screen from before the warning display

Even if the cause of the warning display is not eliminated, you can return to the screen that was displayed before the warning display. If you press the switch, the display screen switches to the screen display from before the warning and the warning (A) is also displayed.

If you want to switch the display

• Warning display screens with the “ ” mark displayed in the upper right of the screen can be switched. If you want to switch the display, press the switch for approximately 2 seconds or more.

Redisplay of a warning display screen

• When the warning is displayed, if you press the switch or switch a few times, the warning display screen you switched from is redisplayed.

Other interrupt displays

• The operation status of each system is displayed on the information screen.
• For further details, refer to the appropriate page in the warning display list.

warning display screen

This is displayed when you press the switch and return from the warning display screen to the previous screen. This mark is also displayed if there is another warning other than the one displayed. When the cause of the warning display is eliminated, the warning goes out automatically.

NOTE

• When the warning is displayed, the warning display screen can be redisplayed on the information screen. Refer to “Information screen (with the ignition switch in “OFF” position or the operation mode in OFF)” on. Refer to “Information screen (with the ignition switch or the operation mode in ON)”

Door ajar warning display screen

If any of the doors or the liftgate is not completely closed, this displays the open door or liftgate. If the speed increases to approximately 5 mph (8 km/h) or higher with a door ajar, a tone will sound four times to inform you that a door is ajar.

CAUTION: Always make sure that the warning display goes out before beginning to drive.

Engine coolant temperature display

• Shows the engine coolant temperature. If the coolant becomes hot, “ ” will blink. Pay careful attention to the engine coolant temperature display while you are driving.

CAUTION: If the engine is overheating, “ ” will blink. In this case, the bar graph is on the red zone. Immediately park the vehicle in a safe place and take the required measures. Refer to “Engine overheating”.

Fuel remaining display screen

Shows the amount of fuel remaining.

• F- Full
• E- Empty

CAUTION: Running out of gas could damage the catalytic converter. If the warning display appears, refuel immediately.

NOTE

• It may take several seconds to stabilize the display after refilling the tank.
• If fuel is added with the ignition switch or the operation mode in ON, the remaining fuel display may incorrectly indicate the fuel level.
• The arrow (A) indicates that the fuel tank filler door is located on the left side of the vehicle. (Refer to “Filling the fuel tank”.

Fuel remaining warning display

When the fuel level runs low, the information screen switches to the interrupt display of the fuel remaining warning display and the mark (B) on the fuel remaining display flashes. If the warning display appears, refuel immediately.

NOTE: On hills or curves, the display may be incorrect due to the movement of fuel in the tank.

Outside temperature display screen

• Shows the temperature outside the vehicle.

NOTE

• The display setting can be changed to the preferred units (°F or °C).
• Depending on factors such as the driving conditions, the displayed temperature may vary from the actual outside temperature.

Odometer

• Shows the total distance traveled.

Trip odometer

• Shows the distance traveled between two points.
• Usage examples for trip odometer A, trip odometer B.
• It is possible to measure two currently traveled distances, from home using trip odometer A and from a particular point on the way using trip odometer B.

To reset the trip odometer

• To return the display to “0”, hold down the switch for approximately 2 seconds or more. Only the currently displayed value will be reset.

Example

If trip odometer A is displayed, only trip odometer A will be reset.

• Both trip odometers A and B can count up to 9999.9 miles/kilometers. When a trip odometer goes past 9999.9 miles/kilometers, it returns to 0.0 miles/kilometers.
• When disconnecting the battery terminal, the memories of trip odometer displays A and B are cleared, and their displays return to “0.0 miles/kilometers”.

Service reminder

• Displays the approximate time until the next recommended periodic inspection. “—” is displayed when the inspection time has arrived.

NOTE: The service reminder time can be modified by an authorized Mitsubishi Motors dealer, to adjust for severe usage, etc. Refer to “Severe maintenance schedule” in your vehicle’s Warranty and Maintenance Manual. For further information, please contact your authorized Mitsubishi Motors dealer.

1. Shows the time until the next periodic inspection.
   • NOTE: Shows the distance in units of 100 miles (100 km) and the time in units of 1 month.
2. This informs you that a periodic inspection is due. Contact an authorized Mitsubishi Motors dealer or a repair facility of your choice to have the system checked.
   • At that time, when the ignition switch is switched from the “OFF” position to the “ON” position or the operation mode is changed from OFF to ON, the warning display is displayed for a few seconds on the information screen.
3. After your vehicle is inspected at an authorized Mitsubishi Motors dealer, it displays the time until the next periodic inspection.

To reset

The “—” display can be reset while the ignition switch or the operation mode is in OFF. When the display is reset, the time until the next periodic inspection is displayed and the warning display is no longer displayed when the ignition switch is switched from the “OFF” position to the “ON” position or the operation mode is changed from OFF to ON.

1. When you press the switch or switch, the information screen switches to the service reminder display screen.
2. Press and hold the switch (for approximately 2 seconds or more) to display “ ” and make it flash. (If there is no operation for approximately 10 seconds with this indicator flashing, the display returns to the previous screen.)
3. With this indicator flashing, if you press the switch, the screen switches from “- –” to “CLEAR”. After that, the time until the next periodic inspection is shown.

CAUTION: The customer is responsible for making sure that regular inspections and maintenance and periodic inspections and maintenance are performed. Inspections and maintenance must be performed to prevent accidents and malfunctions.

NOTE

• The “—” display cannot be reset while the ignition switch or the operation mode is in ON.
• When “—” is displayed, after a certain distance and a certain period of time, the display is reset and the time until the next periodic inspection is displayed.
• If you accidentally reset the display, consult an authorized Mitsubishi Motors dealer for assistance.

System check screen

When the ignition switch is turned to the “ON” position or the operation mode is put in ON, the system check screen is displayed for approximately 4 seconds. If there is no fault, the information screen is displayed. If there is a fault, the screen changes to warning display. Refer to “Warning display list”.

Driving range display

• Shows the approximate driving range (how many more miles or kilometers you can drive).
• When this driving range falls below 30 miles (50 km), “—” is displayed. Refuel immediately.

NOTE

• The driving range is determined based on the fuel consumption data. This may vary depending on the driving conditions and habits. Treat the distance displayed as just a rough guideline.
• When you refuel, the driving range display is updated. However, if you only add a small amount of fuel, the correct value will not be displayed. Fill to a full tank whenever possible.
• When your vehicle is stopped on an extremely steep hill, the driving range value may, change. This is due to the movement of fuel in the tank and does not indicate any breakdown.
• The display setting can be changed to the preferred units (miles or km). Refer to “Changing the function settings”.

Average fuel consumption display

This displays the average fuel consumption from the last reset to the present. There are 2 types of mode settings of manual reset and automatic reset. Refer to “Changing the reset mode for average fuel consumption and average speed”. For information on how to change the average fuel consumption display setting, refer to “Changing the function settings”

NOTE

• The average fuel consumption display can be reset separately in both auto reset mode and manual reset mode.
• “—” is displayed when the average fuel consumption cannot be measured.
• The initial (default) setting is “Auto reset mode”.
• Average fuel consumption may vary depending on the driving conditions (road conditions, how you drive, etc.) The actual fuel consumption may differ from the fuel consumption displayed, so treat the fuel consumption displayed as just a rough guideline.
• Disconnecting the battery cable will erase from memory the manual reset mode or auto reset mode setting for the average fuel consumption display.
• The display setting can be changed to the preferred units {mpg (US), mpg (UK), L/100km or km/L}. Refer to “Changing the function settings”

Average speed display

This displays the average speed from the last reset to the present. There are 2 types of mode setting of manual reset and automatic reset. Refer to “Changing the reset mode for average fuel consumption and average speed”. For the method for changing the average speed display setting, refer to “Changing the function settings”.

NOTE

• The average speed display can be reset separately in both auto reset mode and manual reset mode.
• “—” is displayed when the average speed cannot be measured.
• The initial (default) setting is “Auto reset mode”.
• The display setting can be changed to the preferred units (mph or km/h). Refer to “Changing the function settings”.
• Disconnecting the battery cable will erase from memory the manual reset mode or auto reset mode setting for the average speed display.

Instant fuel consumption display

While driving, the instant fuel consumption is shown with a bar graph. The “ ” mark in the instant fuel gauge shows the average fuel consumption. When the instant fuel consumption surpasses the average fuel consumption, the instant fuel consumption is displayed with a green bar graph. Be conscious of maintaining the instant fuel consumption above the average fuel consumption it can help you drive with the better fuel consumption.

NOTE

• When the instant fuel consumption cannot be measured, a bar graph is not shown.
• The display setting can be changed to the preferred units {mpg (US), mpg (UK), L/100km or km/L}. Refer to “Changing the function settings”
• It is possible to cancel the green bar graph. Refer to “Changing the function settings”

ECO indicator

• This indicator will be displayed when fuel efficient driving is achieved.

ECO Drive Assist

This function displays how fuel-efficiently you are driving under different driving conditions. The ECO drive assist display will change as follows if you do fuel-efficient driving using the accelerator in a way well matched with the vehicle speed.

NOTE: The ECO drive assist is displayed only when vehicle is driven with the selector lever in the “D” (DRIVE) position or when vehicle is driven in the sport mode (for vehicles equipped with sportronic steering wheel paddle shifter).

ECO Score

ECO score indicates the points you have scored on fuel-efficient driving by the number of leaves as follows:

[When the ignition switch or the operation mode is ON]

• The display shows the score you achieved in the last several minutes.

[When the ignition switch is turned to the “OFF” position or the operation mode is put in OFF]

The display shows the overall ECO score the function has counted from the time when the ignition switch is turned to the “ON” position to the time when it is turned to the “OFF” or “ACC” position, or from the time when the operation mode is set to ON to the time when it is set to OFF.

Changing the function settings

1. Park your vehicle in a safe place. Firmly apply the parking brake and move the selector lever into the “P” (PARK) position.
2. When you press the switch or switch, the information screen switches to the function setting screen. Refer to “Information screen (With the ignition switch or the operation mode in ON)”
   • CAUTION: For safety, stop the vehicle before operating. While driving, even if you operate the multi information display switches ( , , ), the function setting screen is not displayed.
3. Press the switch to switch to the top screen (A) for the menu screens. Then, press the switch or switch to switch to the menu screens (B).

• : switch
• : switch or switch

1. Changing the reset mode for average fuel consumption and average speed
2. Changing the fuel consumption display unit
3. Changing the temperature unit
4. Changing the display language
5. Changing the language on other system to match the multi-information display (if so equipped)
6. Operation sound setting
7. Changing the time until “REST REMINDER” is displayed
8. Changing the turn signal sound
9. Changing the instant fuel consumption display
10. Changing the navigation information display (if so equipped)
11. Blind Spot Warning (BSW): To operate (if so equipped)
12. Tire ID set change
13. Returning to the factory settings

NOTE: If no operations are made within approximately 30 seconds of the menu screen being displayed, the display returns to the function setting screen.

1. After switching to the menu screen (B) for the setting you want to change, press the switch to switch to the setting selection screen. For further details on the operation methods, refer to each sections.

NOTE

• If the battery is disconnected, these function settings are reset from memory to the factory settings automatically (except “Blind Spot Warning (BSW): To operate” and “Tire ID set change”).
• You cannot select an item that is displayed dimly on the menu.

Changing the reset mode for average fuel consumption and average speed

You can change the mode condition for the average fuel consumption and average speed display to “Auto reset” or “Manual reset.”

1. Switch to the function setting screen. Refer to “Changing the function settings”.
2. Press the switch or switch several times to switch to the “AVERAGE FUEL CONSUMPTION RESET MODE” screen. Then, press the switch to switch to the setting selection screen.
3. Press the switch or switch to select the reset mode, and then press the switch to confirm the setting. The setting is changed to the selected reset condition.

Manual reset mode

• If you press and hold the switch when the average fuel consumption and average speed are displayed, these calculations will be reset to zero.
• When the following operation is performed, the mode setting changes automatically from manual to auto.

[Except for vehicles equipped with the F.A.S.T.-key]

• Turn the ignition switch to the “ON” position from the “ACC” or “OFF” position.

[For vehicles equipped with the F.A.S.T.- key]

• Change the operation mode to ON from ACC or OFF.

Auto reset mode

• When the average fuel consumption and average speed are being displayed, if you press and hold the switch, these calculations will be reset to zero.
• When the engine switch or the operation mode is in the following conditions, the average fuel consumption display and the average speed display will automatically reset.

[Except for vehicles equipped with the F.A.S.T.-key]

The ignition switch has been set to the “ACC” or “OFF” position for approximately 4 hours or more.

[For vehicles equipped with the F.A.S.T.- key]

• The operation mode has been in ACC or OFF for approximately 4 hours or more.

NOTE

• The average fuel consumption display and average speed display can be reset separatelyin both auto reset mode and manual reset mode.
• Disconnecting the battery cable will erase from memory the manual reset mode or auto reset mode setting for the average speed display and average fuel consumption display.
• The initial (default) setting is “Auto reset mode”.

Changing the fuel consumption display unit

The fuel consumption display unit can be changed. The distance, speed, and amount units are also changed to match the selected fuel consumption unit.

1. Switch to the function setting screen. Refer to “Changing the function settings”
2. Press the switch or switch several times to switch to the “FUEL CONSUMPTION UNIT” screen. Then, press the switch to switch to the setting selection screen.
3. Press the switch or switch to select the units, and then press the switch to confirm the setting. The setting is changed to the selected unit.

NOTE

• The display units for the driving range, the average fuel consumption, the average speed and the instant fuel consumption are changed, but the units for the indicating needle (speedometer), the odometer and the trip odometer will remain unchanged.
• If the battery is disconnected, the memory of the unit setting is erased and is automatically set to {mpg (US) or L/100 km}.

The distance and speed units are also changed in the following combinations to match the selected fuel consumption unit.

Fuel economy	Distance (driving range)	Speed (average speed)
km /L	km	km /h
L /100 km	km	km /h
mpg (US)	mile (s)	mph
mpg (UK)	mile (s)	mph

Changing the temperature unit

The temperature display unit can be switched.

1. Switch to the function setting screen. Refer to “Changing the function settings”.
2. Press the switch or switch several times to switch to the “TEMPERATURE UNIT” screen. Then, press the switch to switch to the setting selection screen.
3. Press the switch or switch to select the units, and then press the switch to confirm the setting. The setting is changed to the selected temperature unit.

NOTE

• If the battery is disconnected, the memory of the language setting is erased and is automatically set to ENGLISH.
• If “—” is selected in the language setting, a warning message is not displayed when there is a warning display or interrupt display.

Changing the language on other system to match the multi-information display (if so equipped)

The language used in Multi Around Monitor (if so equipped) or Head Up Display (HUD) (if so equipped) can be changed automatically to the same language as that shown in the multi-information display.

1. Switch to the function setting screen. Refer to “Changing the function settings”.
2. Press the switch or switch several times to switch to the “LANGUAGE SYNC” screen. Then, press the switch to switch to the setting selection screen.
3. Press the switch or switch to select the setting, and then press the switch to confirm the setting.

NOTE

• If the battery is disconnected, the language cooperative control is automatically set to “ON” (language cooperation: enabled).
• The language cooperation setting can be switched in the following manner.
  • When “ON” (language cooperation: enabled) has been selected, the language for Multi Around Monitor (if so equipped) or Head Up Display (HUD) (if so equipped) is automatically changed to the language selected for the multi-information display. However, this changing function may not work depending on the language selected for the multi-information display.
  • When “OFF” (language cooperation: disabled) has been selected, the language for Multi Around Monitor (if so equipped) or Head Up Display (HUD) (if so equipped) is not automatically changed to match the language selected for the multi-information display.
• The language on the audio system’s display does not automatically change when you select “ON” (language cooperation: enabled) in the language cooperation control.

Operation sound setting

You can change the operation sounds of the multi-information display switches and rheostat illumination button.

1. Switch to the function setting screen. Refer to “Changing the function settings”.
2. Press the switch or switch several times to switch to the “OPERATION SOUND” screen. Then, press the switch to switch to the setting selection screen.
3. Press the switch or switch to select the sound, and then press the switch to confirm the setting. The setting is changed to the selected condition.

NOTE

• If the battery is disconnected, the memory of the operation sound setting is erased and is automatically set to ON (operation sound on).
• The operation sound setting only deactivates the operation sound of the multi-information display switches and rheostat illumination button. The warning display and other sounds cannot be deactivated.

Changing the time until “REST REMINDER” is displayed

The time until the display appears can be changed.

1. Switch to the function setting screen.
2. Press the switch or switch several times to switch to the “REST REMINDER” screen. Then, press the switch to switch to the setting selection screen.
3. Press the switch or switch to select the time, and then press the switch to confirm the setting. The setting is changed to the selected time.

NOTE

• If the battery is disconnected, the memory of the unit setting is erased and is automatically set to the “OFF”.
• The drive time is reset when the ignition switch is in the “OFF” position or the operation mode is in OFF.

Changing the turn signal sound

It is possible to change the turn signal sound.

1. Switch to the function setting screen. Refer to “Changing the function settings”.
2. Press the switch or switch several times to switch to the “TURN SIGNAL SOUND” screen. Then, press the switch to switch to the setting selection screen.
3. Press the switch or switch to select the sound, and then press the switch to confirm the setting. The setting changes to the selected turn signal sound

Changing the instant fuel consumption display

It is possible to change the bar graph setting of the instant fuel consumption display.

1. Switch to the function setting screen. Refer to “Changing the function settings”.
2. Press the switch or switch several times to switch to the “INSTANT FUEL CONSUMPTION DISPLAY” screen. Then, press the switch to switch to the setting selection screen.
3. Press the switch or switch to select the setting, and then press the switch to confirm the setting. The setting changes to the selected bar graph setting.

Changing the navigation information display (if so equipped)

On vehicles equipped with the SDA navigation system, you can select whether to display the navigation information on the information screen.

1. Switch to the function setting screen. Refer to “Changing the function settings”.
2. Press the switch or switch several times to switch to the “NAVI INFORMATION” screen. Then, press theswitch to switch to the setting selection screen.
3. Press the switch or switch to select the setting, and then press the switch to confirm the setting. The setting is changed to the selected navigation information display setting.

Returning to the factory settings

Many of the function settings can be returned to their factory settings.

1. Switch to the function setting screen. Refer to “Changing the function settings”.
2. Press the switch or switch several times to switch to the “FACTORY RESET” screen. Then, press the switch to switch to the setting selection screen.
3. Press the switch or switch to select “RESET”, and then press and hold the switch for approximately 5 seconds or more to confirm the setting.

The buzzer sounds and all of the function settings are returned to the factory settings.

NOTE

• The factory settings are as follows.
  • “AVERAGE FUEL CONSUMPTION RESET MODE”: AUTO
  • “FUEL CONSUMPTION UNIT”: mpg (US) or (L/100 km)
  • “TEMPERATURE UNIT”: °F (Fahrenheit) or °C (Celsius)
  • “LANGUAGE”: ENGLISH
  • “LANGUAGE SYNC”: ON
  • “OPERATION SOUND”: ON
  • “REST REMINDER”: OFF
  • “TURN SIGNAL SOUND”: SOUND 1
  • “INSTANT FUEL CONSUMPTION DISPLAY”: ON
  • “NAVI INFORMATION”: ON
• “BSW” and “TPMS ID” cannot be returned to their factory settings.

FAQ