2023 Mitsubishi Mirage Instrument Cluster Guidelines

The 2023 Mitsubishi Mirage Instrument Cluster is a sleek, contemporary digital dashboard made to give drivers access to crucial data in a simple, intuitive way. This cutting-edge instrument panel has a colorful digital display with integrated critical information including speed, fuel level, engine performance, and navigational instructions. The instrument cluster in the most recent Mirage model improves the driving experience by making it simpler for drivers to keep informed and focused on the road ahead thanks to its straightforward design and configurable settings.

Instrument cluster

1. Tachometer
2. Multi-information display 
3. Speedometer 
4. Multi-information display switch

Speedometer
The speedometer shows the vehicle speed in miles per hour (mph) or kilometers per hour (km/h).

Tachometer
The tachometer shows engine revolutions per minute. This allows the driver to determine the most efficient selector position and engine speed combinations.
This gauge also assists in evaluating engine performance.

CAUTION
The red zone indicates an engine speed beyond the range of safe operation.
Select the correct shift position (manual transaxle) or selector position (CVT) to control the engine speed so that the tachometer indicator does not enter the red zone.

Multi-information display
The multi-information display includes the odometer, trip odometer, service reminder, fuel remaining, selector lever position, aver-age fuel consumption, driving range, etc.

1. Information display
2. Frozen road warning 
3. Fuel remaining display 
4. Selector lever position display

NOTE
When the ignition switch or the operation mode is in OFF, the selector lever position display, fuel remaining display and frozen road warning are not displayed.

Information display
Each time you lightly press the multi-information display switch (A), the display switches in the following order.

1. Odometer 
2. Trip odometer
3. Trip odometer
4. Instrument panel light dimmer control 
5. Driving range display 
6. Average fuel consumption display 
7. Outside temperature display 
8. Service reminder (distance) 
9. Service reminder (month)

NOTE

• When the ignition switch or the operation mode is in OFF, the driving range display, average fuel consumption display and outside temperature display are not displayed.
• While driving, the service reminder is not displayed even if you operate the multi-information display switch.

NOTE

• When the parking lights are not illuminated, the instrument panel light dimmer control is not displayed even if you operate the multi-information display switch.

Odometer
The odometer indicates the total distance the vehicle has traveled.

Trip odometer

The trip odometer indicates the distance traveled between two points.

Usage examples for trip odometer A odometer  B, trip
It is possible to measure two currently traveled distances, from home using trip odometer and from a particular point on the way using trip odometer .

To reset the trip odometer
To return the display to 0, hold down the multi-information display switch for about 1 second or more. Only the currently displayed value will be reset.

Example
If trip odometer A is displayed, only trip odometer A will be reset.

NOTE

• Both trip odometers  A and  B can count up to 9999.9 miles/kilometers.
  When a trip odometer goes past 9999.9 miles/kilometers, it returns to 0.0 miles/kilo-meters.
  When disconnecting the battery terminal, the memories of trip odometer displays  are cleared, A and B  their displays return to “0.0 miles/kilometers”.

Instrument panel light dimmer control
Turn the parking lights on and press the multi-information display switch (2), there is a sound and the brightness changes.

1. Brightness level
2. Multi-information display switch

NOTE

• When the parking lights are illuminated, you can adjust to 8 levels.
• Each time you reduce two brightness levels, the segment display of the brightness level decreases by one segment.
• If you press and hold the switch for longer than about 1 second, the brightness automatically scrolls through its different levels, and stops scrolling when you release the switch. Select your desired level of brightness.

NOTE

• The brightness level of the instruments is stored when the ignition switch is turned to the “OFF” position or the operation mode is put in OFF.
• On vehicles equipped with the automatic light control, the instrument panel light dimmer control display is not displayed when it is bright outside the vehicle and the ignition switch or the operation mode is ON.

Driving range display

This displays the approximate driving range (how many more miles or kilometers you can drive). When the driving range falls below approximately 30 miles (50 km), “—” is dis-played.

NOTE

• The driving range is determined based on the fuel consumption data. This may vary depending on the driving conditions and habits. Treat the distance displayed as just a rough guideline.
• When you refuel, the driving range display is updated.
  However, if you only add a small amount of fuel, the correct value will not be displayed. Fill to a full tank whenever possible.

NOTE

• When your vehicle is stopped on an extremely steep hill, the driving range value may change. This is due to the movement of fuel in the tank and does not indicate any breakdown.
• The display setting can be changed to the preferred units (miles or km).

Average fuel consumption dis-play
This displays the average fuel consumption from the last reset to the present.
The reset mode conditions for the average fuel consumption display can be switched between “Auto reset” and “Manual reset”. For information on how to change the aver-age fuel consumption display setting, refer to “Changing the function settings” on page

NOTE

• The average fuel consumption display can be reset separately in both auto reset mode and manual reset mode.
• is displayed when the average fuel consumption cannot be measured.

NOTE

The initial (default) setting is “Auto reset mode”.
Average fuel consumption may vary depend on the driving conditions (road conditions, how you drive, etc.).
The actual fuel consumption may differ from the fuel consumption displayed, so treat the fuel consumption displayed as just a rough guideline.
Disconnecting the battery cable will erase from memory the manual reset mode or auto reset mode setting for the average fuel consumption display.
The display setting can be changed to the preferred units {mpg, km/L, L/100 km}. 

Outside temperature display
Shows the temperature outside the vehicle.

NOTE

• The display setting can be changed to the preferred units (°F or °C).
• Depending on factors such as the driving conditions, the displayed temperature may vary from the actual outside temperature.

Frozen road warning
If the outside air temperature drops below approx. 37 °F (3 °C), the alarm sounds and the outside air temperature warning symbol (A) flashes for about 10 seconds.

CAUTION

• There is a danger the road might be icy, even when this symbol is not flashing, so please take care when driving.

Fuel remaining display
The fuel remaining display indicates the fuel level in the fuel tank when the ignition switch or the operation mode in ON.

• 1- Full
• 0- Empty

NOTE

• It may take several seconds to stabilize the display after refilling the tank.
• If fuel is added with the ignition switch or the operation mode in ON, the remaining fuel display may incorrectly indicate the fuel level.
• The fuel lid mark (A) indicates that the fuel tank filler door is located on the left side of the vehicle.

Fuel remaining warning display
When the remaining fuel level runs low (one segment is displayed), the last segment of the fuel gauge flashes when the ignition switch is turned to the “ON” position or the operation mode is changed to ON.
When the remaining fuel level runs very low (no segments displayed), the bar graph flashes.
If the warning display appears, refuel immediately.

NOTE

• On hills or curves, the display may be incorrect due to the movement of fuel in the tank.

CAUTION

• Running out of gas could damage the cata-lytic converter. If the warning display appears, refuel immediately.

Service reminder
Displays the approximate time until the next recommended periodic inspection. “—” is displayed when the inspection time has arrived.

NOTE

• The service reminder time can be modified by an authorized Mitsubishi Motors dealer, to adjust for severe usage, etc. Refer to “Severe maintenance schedule” in your vehicle’s Warranty and Maintenance Manual. For further information, please contact your authorized Mitsubishi Motors dealer.

1. Shows the time until the next periodic inspection.
   NOTE
   Shows the distance in units of 100 miles (100 km) and the time in units of 1 month.
2. This informs you that a periodic inspection is due. Contact an authorized Mitsubishi Motors dealer or a repair facility of your choice to have the system checked.
3. After your vehicle is inspected at an authorized Mitsubishi Motors dealer, it displays the time until the next periodic inspection.

NOTE

When the next periodic inspection is approaching, the wrench symbol will be dis-played whenever the ignition switch is turned from the “OFF” position to the “ON” position or when the operation mode is changed from OFF to ON.
The wrench symbol will continuously be dis-played, even on non-service reminder dis-plays (odometer, trip meter, etc.), until the service reminder is reset.
When the service reminder resets, the wrench symbol will not be displayed until the next periodic inspection.

To reset

The “—” display can be reset while the ignition switch or the operation mode is in OFF.

1. When you lightly press the multi-information display switch a few times, the information display switches to the service reminder display.
2. Press and hold the multi-information dis- play switch for about 1 second or more to make the wrench symbol start flashing. (If there is no operation for about 10 seconds with flashing, the display will revert to its original indication.)
3. With this indicator flashing, if you lightly press the multi-information meter switch, the display switches from “—” to “cLEAr”. After that, the time until the next periodic inspection is shown.

CAUTION

• The customer is responsible for making sure that regular inspections and maintenance and periodic inspections and maintenance are performed.
• Inspections and maintenance must be per-formed to prevent accidents and malfunctions.

NOTE

• The “—” display cannot be reset while the ignition switch or the operation mode is in ON.

NOTE

• When “—” is displayed, after a certain distance and a certain period of time, the dis-play is reset and the time until the next periodic inspection is displayed.
• If you accidentally reset the display, consult an authorized Mitsubishi Motors dealer for assistance.

Changing the function settings
The “Average fuel consumption reset mode”, “Fuel consumption unit” and “Temperature unit” setting can be modified as desired, when the ignition switch or the operation mode is ON.

CAUTION

• The driver should not operate the display while the vehicle is in motion.
• When operating the system, stop the vehicle in a safe area.

Changing the reset mode for aver-age fuel consumption
You can change the mode condition for the average fuel consumption display to “Auto reset” or “Manual reset”.

1. When you lightly press the multi-information display switch a few times, the information display switches to the driving range display.
2. Each time you press the multi-information display switch for 1 second or more on driving range display, you can switch reset mode for average fuel consumption.(A: Auto reset mode, B: Manual reset mode)

Manual reset mode

When the average fuel consumption is being displayed, if you hold down the multiinformation display switch, these calculations will be reset to zero.
When the following operation is per-formed, the mode setting changes automatically from manual to auto.

[Except for vehicles equipped with the F.A.S.T.-key]
Turn the ignition switch to the “ON” position from the “ACC” or “OFF” position.

[For vehicles equipped with the F.A.S.T.-key]
Change the operation mode to ON from ACC or OFF.

Auto reset mode

When the average fuel consumption is being displayed, if you hold down the multi-information display switch, these calculations will be reset to zero.
When the engine switch or the operation mode is in the following conditions, the average fuel consumption display will automatically reset.

[Except for vehicles equipped with the F.A.S.T.-key]
The ignition switch has been set to the “ACC” or “OFF” position for about 4 hours or more.

[For vehicles equipped with the F.A.S.T.-key]
The operation mode has been set to ACC or OFF for about 4 hours or more.

NOTE

• The average fuel consumption display can be reset separately for the auto reset mode and for the manual reset mode.
• Disconnecting the battery cable will erase from memory the manual reset mode or auto reset mode setting for the average fuel consumption display.
• The initial (default) setting is “Auto reset mode”.

Changing the fuel consumption display unit The fuel consumption display unit can be changed. The distance and amount units are also switched to match the selected fuel consumption unit.

1. When you lightly press the multi-information display switch a few times, the information display switches to the average fuel consumption display.
2. Press and hold the multi-information dis-play switch for about 5 seconds or more until buzzer sound is heard twice.
3. Press and hold the multi-information dis- play switch to switch in sequence from “km/L”  “L/100 km”  “mpg”  “km/L”.

NOTE

• The display units for the driving range, the average fuel consumption are changed, but the units for the indicating needle (speedometer), the odometer, the trip odometer and the service reminder will remain unchanged.
• If the battery is disconnected, the memory of the unit setting is erased and it returns automatically to factory setting.

The distance units is also changed in the fol-lowing combinations to match the selected fuel consumption unit.

Fuel consumption	Distance (driving range)
km/L	km
L/100 km	km
mpg	mile (s)

Changing the temperature unit 
The temperature display unit can be switched.

1. When you lightly press the multi-information display switch a few times, the information display switches to the outside temperature display.
2. Each time you press the multi-information display switch for 5 seconds or more on outside temperature display, you can switch from °F to °C or from °C to °F unit of outside temperature display.

NOTE
The temperature value on air conditioning panel is switched in conjunction with outside temperature display unit of the multi-information display.
However, “°F” or “°C” are not shown to temperature display of an air conditioning.

FAQs

Useful Link

View Full PDF : 2023 Mitsubishi Mirage Owner’s Manual | Auto User Guide