2023 Mitsubishi Outlander PHEV Engine Oil and Fluids Instructions

The 2023 Mitsubishi Outlander PHEV is an example of cutting-edge car technology because it combines a hybrid economy with strong performance without any problems. To keep your engine healthy and make it last as long as possible, you must follow the rules for engine oil and chemicals. Mitsubishi suggests using high-quality synthetic oil that is made to meet the specific needs of the Outlander PHEV’s advanced powertrain. To get the most out of your car’s speed and gas mileage, you should always change the oil at the times recommended in the owner’s manual. It is also very important to pay close attention to other important fluids, like transmission oil and coolant. Following the manufacturer’s instructions for regular checks and replacements at the right times helps the car stay reliable and keep working. By carefully following these steps, Outlander PHEV owners can make sure that their car stays a model of efficiency, combining electric and internal combustion power sources in a way that makes driving an absolute pleasure.

ENGINE OIL

TO CHECK AND REFILL ENGINE OIL

The engine oil used has a significant effect on the engine’s performance, service life, and stability. Be sure to use oil of the recommended quality and appropriate viscosity.
All engines consume a certain amount of oil during normal operation. Therefore, it is important to check the oil level at regular intervals or before starting a long trip.

1. Park the vehicle on a horizontal surface.
2. Stop the Plug-in Hybrid EV System.
3. Wait a few minutes.
4. Remove the dipstick and wipe it with a clean cloth.
5. Reinsert the dipstick as far as it goes.
6. Remove the dipstick and confirm that the oil level is between the marks “L” and “F”.
7. If the oil level is less than the level indicated by the mark “L”, remove the cap and add enough oil to raise the level between the marks “L” and “F”.
8. After adding oil, close the cap securely.
9. Confirm the oil level by repeating steps 4 to 6.

NOTE:

• To avoid engine damage, do not overfill by exceeding the mark “F”.
• Be sure to use the specified engine oil and do not mix various types of oil.
• When the oil level is checked in step 6 above, check it on the low side of the dipstick because it is different in appearance from the oil level on the two sides of the dipstick.
• The engine oil will deteriorate rapidly if the vehicle is subjected to severe conditions, requiring earlier oil replacement. Please refer to the maintenance schedule.
• For handling of used engine oils, refer to “Safety and disposal information for used engine oil

CHANGING ENGINE OIL AND FILTER
Engine oil and oil filters should be replaced at the time or mileage specified in the maintenance interval. It is recommended to visit a certified Mitsubishi EV dealer for this service.

WARNING

• Prolonged and repeated contact with used engine oil may cause skin cancer.
• Try to avoid direct skin contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.
• Keep used engine oil out of reach of children.

BRAKE FLUID
For additional brake fluid information, see “Capacities and recommended fluids/lubricants” (P.12-2) of this manual.

WARNING

• Use only new fluid from a sealed container. Old, inferior, or contaminated fluid may damage the brake system. The use of improper fluids can damage the brake system, and affect the vehicle’s stopping ability.
• Clean the filler cap before removing it.
• Brake fluid is poisonous and should be stored carefully in marked containers out of the reach of children.

CAUTION
Do not spill the fluid on any painted surfaces. This will damage the paint. If fluid is spilled, immediately wash the surface with water.

Check the fluid level in the reservoir. If the fluid is below the MIN line or the brake warning light comes on, add MITSUBISHI MOTORS GENUINE BRAKE FLUID SUPER4 (DOT 4) or conform to brake fluid DOT 3 or DOT 4 up to the MAX line. If fluid must be added frequently, the system should be checked. It is recommended you visit a certified Mitsubishi EV dealer for this service.
The reservoir cap must be tightly sealed to keep dirt and water out.

WINDOW WASHER FLUID
To check the fluid level, use your finger to plug the center hole of the cap/tube assembly, then remove it from the reservoir. If there is no fluid in the tube, add fluid.
Add a washer solvent to the washer for better cleaning. In the winter season, add a windshield washer antifreeze. Follow the manufacturer’s instructions for the mixture ratio.
Fill the window washer fluid reservoir periodically.
Add fluid when the low washer fluid warning appears.
Refill the reservoir more frequently when driving conditions require an increased amount of window washer fluid.

Recommended fluid:
Mitsubishi Motors Genuine Windshield Washer Concentrate Cleaner & Antifreeze or equivalent

CAUTION

• Do not use any fluid other than water fluid. Also, do not use soapy water, glass cleaner, and engine coolant.
  Other liquids could cause streaking on the vehicle’s painted surfaces, damage the washer pump, or clog the nozzle, leading to the washer fluid not spraying.
• Over-diluting the washer fluid in winter may cause it to freeze on the windshield.

 

FAQs

Useful Link

View Full PDF: 2023 Mitsubishi Outlander PHEV Owners Manual | Auto User Guide

2023 Mitsubishi Outlander PHEV All Wheel Drive (AWD) Instructions