2023 Mitsubishi Outlander PHEV Wipers Operation Instructions
The 2023 Mitsubishi Outlander PHEV is the most cutting-edge car on the market because it combines cutting-edge technology with an eco-friendly economy. One feature that stands out as an example of how user-friendly the car’s design is is how the window wipers work. It was designed so that the wipers work perfectly, and they are easy to use so that you can drive safely and clearly in any weather. With settings that are easy to get to, drivers can quickly change the speed of the wipers and turn on the washer function as needed. The 2023 Mitsubishi Outlander PHEV’s wipers are made to improve visibility and safety, whether it’s pouring rain outside or just a drizzle. This shows that the car is dedicated to making driving as easy as possible while also being environmentally friendly thanks to its plug-in hybrid technology.
WIPER AND WASHER SWITCH
WARNING
In freezing temperatures, the washer solution may freeze on the windshield and obscure your vision which may lead to an accident. Warm the windshield with the defroster before you wash the windshield.
CAUTION
- Do not operate the washer continuously for a long period or the pump may fail.
- Do not operate the washer if the reservoir tank is empty.
- Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol-based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank.
- Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concentrate and water.
NOTE:
In freezing temperatures, make sure the wiper blade rubbers are not frozen to the windshield. If the wiper blade is frozen and stuck on the windshield, turn on the defrost switch of the air conditioner or use the wiper deicer (if so equipped) to warm the windshield.
If the windshield wiper operation is interrupted by snow or ice, the wiper may stop moving to protect its motor. If this occurs, turn the wiper switch to the OFF position and remove the snow or ice that is on and around the wiper arms. In approximately 1 minute, turn the switch on again to operate the wiper.
WINDSHIELD WIPER AND WASHER OPERATION
The windshield wiper and washer operate when the power switch is in the ON position.
Push the lever down to operate the wiper at the following speed:
- Intermittent — intermittent operation can be adjusted by turning the knob toward (Faster) or (Slower). Also, the intermittent operation speed varies by the vehicle speed. (For example, when the vehicle speed is high, the intermittent operation speed will be faster.)
- Low — continuous low-speed operation
- High — continuous high-speed operation
Push the lever up 4 to have one sweep operation of the wiper.
Pull the lever toward you 5 to operate the washer. Then the wiper will also operate several times.
NOTE:
The speed-dependent feature may be disabled. For additional information, refer to “Vehicle Settings
RAIN-SENSING AUTO WIPER SYSTEM (if so equipped)
The rain-sensing auto wiper system can automatically turn on the wipers and adjust the wiper speed depending on the rainfall and the vehicle speed by using the rain sensor located on the upper part of the windshield.
To set the rain-sensing auto wiper system, push the lever down to the AUTO position. The wiper will sweep once while the Plug-in Hybrid EV system is running.
The rain sensor sensitivity level can be adjusted by turning the knob upwards (High) or downwards (Low).
- High — High-sensitive operation
- Low — Low sensitive operation
To turn the rain-sensing auto wiper system off, push up the lever to the OFF position, or pull down the lever to the LO or HI position.
CAUTION
Do not touch the rain sensor and around it when the wiper switch is in the AUTO position and the Plug-in Hybrid EV system is running. The wipers may operate unexpectedly and cause an injury or may damage a wiper.
- The rain-sensing auto wipers are intended for use during rain. If the switch is left in the AUTO position, the wipers may operate unexpectedly when dirt, fingerprints, oil film, or insects are stuck on or around the sensor. The wipers may also operate when exhaust gas or moisture affects the rain sensor.
- Do not attach a sticker or label on the windshield. Otherwise, the rain sensor may not detect the amount of the water properly and the wiper may not operate automatically.
- If the replacement of the windshield is
necessary, it is recommended to contact a certified Mitsubishi EV dealer. - The rain-sensing auto wipers may not operate if rain does not hit the rain sensor even if it is raining.
- When the windshield glass is coated with water repellent, the speed of the rain-sensing auto wipers may be higher even though the amount of rainfall is small.
- Be sure to turn off the rain-sensing auto wiper system when you use a car wash.
- Using genuine wiper blades is recommended for the proper operation of the rain-sensing auto-wiper system. (See “Wind-shield wiper blades” (P.10-11) for wiper blade replacement.)
THE REAR WINDOW WIPER AND WASHER SWITCH
WARNING
In freezing temperatures, the washer solution may freeze on the rear window glass and obscure your vision. Warm the rear window with the defroster before you wash the rear window.
CAUTION
- Do not operate the washer continuously for more than 30 seconds.
- Do not operate the washer if the reservoir tank is empty.
- Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol-based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank.
- Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concentrate and water.
NOTE:
In freezing temperatures, make sure the wiper blade rubbers are not frozen to the rear window. If the wiper blade is frozen and stuck on the rear window, use the rear window defroster to warm the rear window.
If the rear window wiper operation is interrupted by snow or ice, the wiper may stop moving to protect its motor. If this occurs, turn the wiper switch to the OFF position and remove the snow or ice that is on and around the wiper arms. In approximately 1 minute, turn the switch on again to operate the wiper.
The rear window wiper and washer operate when the power switch is in the ON position.
Turn the switch clockwise from the OFF position to operate the wiper.
- Intermittent (INT) — intermittent operation (not adjustable)
- Low (ON) — continuous low-speed operation
Push the switch forward to operate the washer. Then the wiper will also operate several times.
Reverse Link feature:
When the windshield wiper switch is on, moving the shift lever to the R (Reverse) position will operate the rear window wiper.
NOTE:
The Reverse Link feature may be disabled. For additional information, refer to “Vehicle Settings
ELECTRIC REAR WINDOW AND DOOR MIRROR DEFROSTER SWITCH
To defog/defrost the rear window glass and door mirrors (if so equipped), start the Plug-in Hybrid EV system and push the switch on. The indicator light will illuminate. Push the switch again to turn the defroster off.
It will automatically turn off in approximately 20 minutes.
CAUTION
When cleaning the inner side of the rear window, be careful not to scratch or damage the electric rear window defroster.
WIPER DEICER SWITCH (if so equipped)
The wiper deicer switch (defroster switch) operates when the Plug-in Hybrid EV system is running.
The deicer is used to remove ice from the windshield when a wiper is frozen to the windshield.
When the switch is pushed, the indicator light illuminates and the deicer operates for approximately 10 minutes. After the preset time has passed, the deicer will turn off automatically. To turn off the deicer manually, push the deicer switch again, and the indicator light turns off.
CAUTION
When cleaning the inner side of the window, be careful not to scratch or damage the electrical conductors on the surface of the window.
FAQs
Locate the wiper control stalk on the right side of the steering column. Push it up to activate the wipers.
Yes, the 2023 Outlander PHEV typically has multiple wiper speed settings. You can adjust them using the wiper control stalk.
Pull the wiper control stalk towards you. This should activate the windshield washer fluid spray while the wipers are on.
Yes, you can usually adjust the intermittent wiper speed by rotating the collar on the wiper control stalk.
Yes, the wiper control stalk typically has an “OFF” position for parking the wipers when not in use.
Check the fuse, make sure the wiper blades are not obstructed, and inspect the wiper fluid level.
Yes, the Outlander PHEV usually comes equipped with a rear wiper. You can control it with a separate switch.
Depending on the trim level, the 2023 Outlander PHEV might offer rain-sensing wipers.
Lift the wiper arm away from the windshield, press the release tab, and slide the old blade out. Install the new blade in the reverse order.
Check the wiper blades regularly for wear and tear. Clean them with windshield washer fluid and replace them if necessary.
It’s recommended to use genuine Mitsubishi wiper blades for optimal performance.
The “AUTO” setting typically enables automatic rain-sensing mode, adjusting the wiper speed based on the intensity of rainfall.
If equipped, there should be a separate control or switch for the rear wiper.
Yes, you can usually switch to a manual mode on the wiper control stalk if the automatic function is not working.
Consider using winter-grade wiper fluid, lifting the wiper arms when parked to prevent freezing to the windshield, and checking for ice buildup regularly.
Useful Link
View Full PDF: 2023 Mitsubishi Outlander PHEV Owners Manual | Auto User Guide