Display Setting: 2020 Mitsubishi L200 Instrument Cluster Guide

Display Setting: 2020 Mitsubishi L200 Instrument Cluster Guide

The 2020 Mitsubishi L200’s instrument cluster is a sophisticated mix of usefulness and modern design. It puts important vehicle information right in front of the driver’s line of sight. When people walk in, the cluster meets them with a dynamic startup sequence that sets the mood for the ride. Its clear digital screen shows a lot of information, like the speed of the vehicle, the engine’s RPM, the amount of fuel in the tank, and the temperature. This makes sure that drivers are always informed and in charge. The easy-to-use layout and high-resolution pictures make it easier to read, even in different lighting conditions, which makes trips safer and more efficient. The 2020 Mitsubishi L200’s instrument panel was made with the driver in mind. It shows the brand’s dedication to innovation and driver-centric engineering, taking the driving experience to a whole new level.

2024 Mitsubishi ECLIPSE CROSS Specs, Price, Features, Mileage (Brochure)

Instruments

1. Tachometer
   The tachometer indicates the engine speed (r/min). The   tachometer helps you to obtain more economical driving and also warns you of excessive engine speeds (Red zone).
2. Multi-information display (Type 1: Col-our liquid crystal display type) ® 
   Information screen display list (Type 1) ® 
   Multi-information display (Type 2: Mono-colour liquid crystal display type) ® 
3. Speedometer (km/h or mph + km/h)
4. Rheostat illumination button (Type 1) ® 
5. Multi-information display switch (Type 2) ® 

CAUTION

• When driving, watch the tachometer to make sure that the engine speed indication does not rise into the red zone (excessive engine rpm).

Meter illumination control -Type 1

Each time you press the rheostat illumination button, there is a sound, and the brightness of the instruments changes.

1. Brightness level
2. Rheostat illumination button

NOTE

• You can adjust to 8 different levels respectively for when the position lamps are illuminated and when they are not.
• If the vehicle is equipped with the automatic lamp control, when the lamp switch is in a position other than the “OFF” position, the meter illumination switches automatically to the adjusted brightness, depending on the brightness outside the vehicle.
• The brightness level of the instruments is stored when the ignition switch is turned off or the operation mode is put OFF.
• If you press and hold the button for about 2 seconds or more when the position lamps are illuminated, the brightness level changes to the maximum level. Pressing and holding the button for about 2 seconds or more again returns the brightness level to the previous level.

Multi-information display -Type 1

Always stop the vehicle in a safe place before operating.
The following information is included on the multi-information display: warnings, odometer, trip meter, average and momentary fuel consumption, average speed, etc.

[When the ignition switch or the operation mode is OFF]

1. mark display ® 
2. Information screen ® p. 5-05 Interrupt display screen ® 
3. Odometer ® 
4. “ mark indicator ®

 

[When the ignition switch or the operation mode is ON]

1. Off Road mode indicator display* ® 
2. Drive mode indicator display* (Vehicles with Easy Select 4WD) ® 
   (Vehicles with Super Select 4WD II) ®
3. mark display ®
4. Forward Collision Mitigation system (FCM) OFF indicator display* ® 
   Ultrasonic misacceleration Mitigation System (UMS) OFF indicator display* ® 
5. Lane Departure Warning (LDW) indicator display* ® 
6. Information screen ®
7. Engine coolant temperature display
8. Odometer ®
9. Cruise control indicator display
10. Speed limiter indicator display* ® 
11. “ ” “ ” mark indicator ® 
12. Gearshift indicator display (vehicles with M/T) ®
13. Selector lever position indicator display (vehicles with A/T) ® 
14. Fuel remaining display ® 
15. Outside temperature display ®
16. Auto Stop & Go indicator display* ® 
    Auto Stop & Go OFF indicator display* ® 

NOTE

• The fuel units, outside temperature units, display language, and other settings can be changed.

Multi-information display switch

Each time the multi-information display switch is operated, the buzzer sounds, and the multi-information display changes between information such as warnings, trip meter, average and momentary fuel consumption, distance range, etc.

It is also possible to change elements such as the language and units used on the multi-information display by operating the multi-information display switch.

NOTE

• Each time the multi-information display back switch is operated, the buzzer sounds, and the multi-information display returns to the position before pressing the multi-information display switch.

Information screen (when the ignition switch or the operation mode is OFF)
Each time you lightly press the multi-information display switch, the screen switches in the following order.

• When there is no warning display
• When there is a warning display

1. Tripmeter A
2. Tripmeter B
3. Auto Stop & Go (AS&G) monitor* ® ECO score display ® 
4. Service reminder ® 
5. Redisplay of a warning display screen ® 

Information screen (when the ignition switch is turned from the “LOCK” position to the “ON” position or the operation mode is changed from OFF to ON)
When the ignition switch is turned to the “ON” position or the operation mode is put in ON, the display screen switches in the following order.

• When the inspection time has arrived

1. Screen when the ignition switch or the operation mode is OFF
2. System check screen ® 
3. Screen when the ignition switch or the operation mode is ON
4. Service reminder ®

Information screen (when the ignition switch or the operation mode is ON)
Each time you lightly press the multi-information display switch, the screen switches in the following order.

• When there is no warning display
• When there is a warning display

1. Tripmeter A
2. Tripmeter B
3. Driving range display ® ECO drive assist display ®
4. Average fuel consumption display ®  ECO drive assist display ® 
5. Average speed display ® Momentary fuel consumption display ® 
6. Auto Stop & Go (AS&G) monitor* ®  ECO score display ® 
7. 2WD/4WD operation indicator display* (Vehicles with Easy Select 4WD) ®  (Vehicles with Super Select 4WD II) ®
8. Service reminder ® 
9. Function setting screen ® 
10. Redisplay of a warning display screen ®

NOTE

• While driving, the service reminders are not displayed even if you operate the multi-information display switch. Always stop the vehicle in a safe place before operating.
• While driving, the function setting screen is not displayed even if you operate the multi-information display switch.
  Always stop the vehicle in a safe place before operating and firmly apply the parking brake and put the gearshift lever into the “N” (Neutral) position (M/T) or the selector lever into the “P” (PARK) position (A/T).
  Refer to “Changing the function settings”.
• When information is to be announced, such as a system fault, the buzzer sounds and the screen display is switched.

Interrupt display screen

Warning display
When information is to be announced, such as a system fault, the buzzer sounds and the information screen is switched to the warning display screen.
Refer to the warning list and take the necessary measures.
When the cause of the warning display is eliminated, the warning display goes out automatically.

To return to the screen displayed before the warning display
Even if the cause of the warning display is not eliminated, you can return to the screen that was displayed before the warning display.
If you press the multi-information display switch, the screen switches to the screen that was displayed before the warning display, and the mark (A) is displayed.

If you want to switch the display
Warning display screens with a “ ” “ ” mark displayed in the upper right of the screen can be switched. If you want to switch the display, press the multi-information display switch as follows.
Press lightly.

Press for approximately 2 seconds or more.

Redisplay of a warning display screen
When the mark is displayed, if you lightly press the multi-information display switch a few times, the warning display screen you switched from is redisplayed.

Other interrupt displays
The operation status of each system is displayed on the information screen.
Refer to the appropriate page in the warning display list for further details.

mark display
This is displayed when you press the multi-information display switch and return from the warning display screen to the previous screen.
This mark is also displayed if there is another warning other than the one displayed. When the cause of the warning display is eliminated, the mark goes out automatically.

NOTE
When the mark is displayed, the warning display screen can be redisplayed on the information screen.
Refer to “Information screen (when the ignition switch or the operation mode is OFF)”.
Refer to “Information screen (when the ignition switch or the operation mode is ON)”.

Engine coolant temperature display

This indicates the engine coolant temperature.
If the coolant becomes hot, “ ” will blink.
Pay careful attention to the engine coolant temperature display while you are driving.

CAUTION
If the engine is overheating, “ ” will blink. In this case, the bar graph is in the red zone. Immediately park the vehicle in a safe place and take the required measures. Refer to “Engine overheating.

Fuel remaining display
This displays the amount of fuel remaining.

• F (1) – Full
• E (0) – Empty

NOTE

• It may take several seconds to stabilize the display after refilling the tank.
• If fuel is added with the ignition switch or the operation mode is in ON, the fuel gauge may incorrectly indicate the fuel level.
• The arrow (A) indicates that the fuel tank filler door is located on the left side of the body.

Fuel remaining warning display
When the fuel is reduced to approximately 10 liters, the information screen switches to the interrupt display of the fuel remaining warning display, and the “ ” mark (B) on the fuel remaining display flashes slowly (approximately once per second). After a few seconds, the information screen returns from the fuel remaining warning display to the previous screen.
If the remaining fuel level is reduced further, the information screen switches to the fuel remaining warning display, and the “ ” mark (B) on the fuel remaining display flashes quickly (approximately twice per second).

CAUTION

• Do not drive with an extremely low fuel level; running out of fuel could cause damage to the fuel system.

NOTE

• On inclines or curves, the display may be incorrect due to the movement of fuel in the tank.

Outside temperature display
This shows the temperature outside the vehicle.

NOTE

• The display setting can be changed to the preferred units (°C or °F).
  Refer to “Changing the function settings”.
• Depending on factors such as the driving conditions, the displayed temperature may vary from the actual outside temperature.

Odometer
The odometer indicates the distance travelled.

Tripmeter
The trip meter indicates the distance travelled between two points.
Example usage of trip meter A and trip meter B

It is possible to measure two currently traveled distances, from home using trip meter A and from a particular point on the way using trip meter B.

To reset the trip meter
To return the display to 0, hold down the multi-information display switch for approximately 2 seconds or more. Only the currently displayed value will be reset.

Example
If trip meter A is displayed, only trip meter A will be reset.

NOTE

• When disconnecting the battery terminal, the memory of the trip meter and B is cleared, and the display returns to “0”.

Service reminder
Displays the approximate time until the next periodic inspection recommended by MITSUBISHI MOTORS. “—” is displayed when the inspection time has arrived.

NOTE

• Depending on the vehicle specifications, the displayed time until the next periodic inspection may differ from that recommended by MITSUBISHI MOTORS.
  In addition, the display settings for the next periodic inspection time can be modified. To modify the display settings, have it adjusted at an MITSUBISHI MOTORS Authorized Service Point.
  For more details, contact an MITSUBISHI MOTORS Authorized Service Point.

1. Displays the time until the next periodic inspection.
   NOTE
   The distance is shown in units of 100 km (100 miles). The time is shown in units of months.
   
2. This informs you that a periodic inspection is due. Consult an MITSUBISHI MOTORS Authorized Service Point. At that time, when the ignition switch is turned from the “LOCK” position to the “ON” position or the operation mode is changed from OFF to ON, the warning display is displayed for a few seconds on the information screen.
3. After your vehicle is inspected at an MITSUBISHI MOTORS Authorized Service Point, it displays the time until the next periodic inspection.

To reset
The “—” display can be reset while the ignition switch or the operation mode is in OFF. When the display is reset, the time until the next periodic inspection is displayed, and the warning display is no longer displayed when the ignition switch is turned from the “LOCK” position to the “ON” position or the operation mode is changed from OFF to ON.

1. When you lightly press the multi-information display switch a few times, the information display switches to the service reminder display screen.
2. Press and hold the multi-information display switch for approximately 2 seconds or more to display “ ” and make it flash. (If there is no operation for approximately 10 seconds with flashing, the display returns to the previous screen.)
3. Lightly press the multi-information display switch while the icon is flashing to change the display from “—” to “CLEAR”. After this, the time until the next periodic inspection will be displayed.

CAUTION

• The customer is responsible for making sure that periodic inspections and maintenance are performed.
  Inspections and maintenance must be performed to prevent accidents and malfunctions.

NOTE

• “—” display cannot be reset when the ignition switch or the operation mode is ON.
• When “—” is displayed, after a certain distance and a certain period, the display is reset and the time until the next periodic inspection is displayed.
• If you accidentally reset the display, consult an MITSUBISHI MOTORS Authorized Service Point.

System check screen
When the ignition switch is turned to the “ON” position or the operation mode is put in ON, the system check screen is displayed for approximately 4 seconds. If there is no fault, the information screen (when the ignition switch or the operation mode is ON) is displayed. If there is a fault, the screen changes to a warning display.
Refer to “Warning display list”.

NOTE

• The system check screen display varies depending on the customer’s equipment.

Driving range display
This displays the approximate driving range (how many more kilometres or miles you can drive). When the driving range falls below approximately 50 km (30 miles), “—” is displayed.
Refuel as soon as possible.

NOTE

• The driving range is determined based on the fuel consumption data. This may vary depending on the driving conditions and habits. Treat the distance displayed as just a rough guideline.
• When you refuel, the driving range display is updated.
  However, if you only add a small amount of fuel, the correct value will not be displayed. Fill with a full tank whenever possible.
• On rare occasions, the value displayed for the driving range may change if you are parked on an extremely steep incline. This is due to the movement of fuel in the tank and does not indicate a malfunction.
• The display setting can be changed to the preferred units (km or miles).

Average fuel consumption display
This displays the average fuel consumption from the last reset to the present time.
The reset mode conditions for the average fuel consumption display can be switched between “Auto-reset” and “Manual reset”. 
For information on how to change the average fuel consumption display setting.

NOTE

• “—” is displayed when the average fuel consumption cannot be measured.
  The initial (default) setting is “Auto reset mode”.
• The average fuel consumption depends on the driving condition (road condition, driving behavior, etc.). The displayed fuel consumption may vary from the actual fuel consumption. Treat the fuel consumption displayed as just a rough guideline.
• The memory of the auto reset mode or manual reset mode for the average fuel consumption display is erased if the battery is disconnected.
• The display setting can be changed to the preferred units {km/L, mpg (US), mpg (UK) or L/100 km}.

Average speed display
This displays the average speed from the last reset to the present time.
The reset mode conditions for the average speed display can be switched between “Auto-reset” and “Manual reset”.
Refer to “Changing the reset mode for average fuel consumption and average speed”.

For the method for changing the average speed display setting, refer to “Changing the function settings”.

NOTE

• The average speed display can be reset separately for the auto reset mode and the manual reset mode.
• “—” is displayed when the average speed cannot be measured.
• The initial (default) setting is “Auto reset mode”.
  The display setting can be changed to the preferred units (km/h or mph).
• The memory of the auto reset mode or manual reset mode for the average speed display is erased if the battery is disconnected.

Momentary fuel consumption display
While driving, this displays the momentary fuel consumption, using a bar graph.

The “ ” mark (A) in the momentary fuel gauge shows the average fuel consumption. When the momentary fuel consumption surpasses the average fuel consumption, the momentary fuel consumption is displayed with a green bar graph.
Be conscious of maintaining a momentary fuel consumption above the average fuel consumption, driving with the better fuel consumption can be possible.

NOTE

• When the momentary fuel consumption cannot be measured, the bar graph is not displayed.
• The display setting can be changed to the preferred units {km/L, mpg (US), mpg (UK) or L/100 km}.
• It is possible to cancel the green bar graph. 

Auto Stop & Go (AS&G) monitor
The accumulated time the engine has been stopped by the Auto Stop & Go (AS&G) system is displayed.

NOTE

• When the ignition switch or the operation mode is ON again, the accumulated time will be reset.

ECO drive assist display
This function displays how fuel-efficiently you are driving under different driving conditions.
The ECO drive assist display will change as follows if you do fuel-efficient driving using the accelerator in a way well matched with the vehicle speed.

NOTE

• On vehicles with A/T, the ECO drive assist is displayed only when the vehicle is driving with the selector lever in the “D” (DRIVE) position or when the vehicle is driving in the sport mode.

ECO score display
The ECO score indicates the points you have scored on fuel-efficient driving by the number of leaves as follows:

[When the ignition switch or the operation mode is ON]
The display shows the score you achieved in the last several minutes.

[When the ignition switch is turned off or the operation mode is put in OFF]

The display shows the overall ECO score the function has counted from the time when the ignition switch is turned to “ON” to the time when it is turned to “LOCK” or “ACC”, or from the time when the operation mode is set to “ON” to the time when it is set to “OFF”.

Changing the function settings
The “Display language”, “Temperature unit”, “Fuel consumption unit”, and “Average fuel consumption and speed reset method” etc. settings can be modified as desired.

1. Stop the vehicle in a safe place.
   Firmly apply the parking brake and put the gearshift lever into the “N” (Neutral) position (M/T) or the selector lever into the “P” (PARK) position (A/T).
2. Lightly press the multi-information display switch a few times to switch the information screen to the function setting screen. CAUTION
   For safety, stop the vehicle before operating. While driving, even if you operate the multi-information display switch, the function setting screen is not displayed.
3. Press and hold the multi-information display switch for approximately 2 seconds or more to switch from the setting mode screen to the menu screen.

NOTE

• To return the menu screen to the function setting screen, press and hold the multi-information display switch for approximately 2 seconds or more.
• If no operations are made within approximately 30 seconds of the menu screen being displayed, the display returns to the function setting screen.

1. Select the item to change on the menu screen and change to the desired setting. Refer to the following items for further details on the operation methods.

NOTE

• If the battery is disconnected, these function settings are reset from memory and are automatically to the factory settings.

Changing the reset mode for average fuel consumption and average speed
The mode conditions for the average fuel consumption and average speed display can be switched between “Auto-reset” and “Manual reset”.

1. Press and hold the multi-information display switch for approximately 2 seconds or more to switch from the setting mode screen to the menu screen.
2. Lightly press the multi-information display switch to select“AVG (average fuel consumption and average speed setting)”.
3. Press and hold the multi-information display switch for approximately 2 seconds or more to switch from A/1 (Auto reset mode) to M/2/P (Manual reset mode), or from M/2/P to A/1.
   The setting is changed to the selected mode condition.

Manual reset mode

• When the average fuel consumption and average speed are being displayed, if you hold down the multi-information display switch, the average fuel consumption and average speed displayed at that time are reset.
• When the following operation is performed, the mode setting is automatically switched from manual to auto.

[Except for vehicles equipped with key-less operation system]
Turn the ignition switch from the “ACC” or “LOCK” position to the “ON” position.

[For vehicles equipped with keyless operation system]
Change the operation mode from ACC or OFF to ON.

Switching to auto occurs automatically. If switching to manual mode is done, however, the data from the last reset is displayed.

Auto reset mode

• When the average fuel consumption and average speed are being displayed, if you hold down the multi-information display switch, the average fuel consumption and average speed displayed at that time are reset.
• When the ignition switch or the operation mode is in the following condition, the average fuel consumption display and average speed display are automatically reset.

[Except for vehicles equipped with key-less operation system]
The ignition switch is in the “ACC” or “LOCK” position for approximately 4 hours or longer.
[For vehicles equipped with keyless operation system]
The operation mode is in ACC or OFF for approximately 4 hours or longer.

NOTE

• The average fuel consumption display and average speed display can be reset separately for the auto reset mode and the manual reset mode.
• The memory of the auto reset mode or manual reset mode for the average fuel consumption display and average speed display is erased if the battery is disconnected.

Changing the fuel consumption display unit
The display unit for fuel consumption can be switched. The distance, speed, and amount of units are also switched to match the selected fuel consumption unit.

1. Press and hold the multi-information display switch for approximately 2 seconds or more to switch from the setting mode screen to the menu screen.
   Refer to “Changing the function settings”.
2. Lightly press the multi-information display switch to select“AVG UNIT (fuel consumption display setting)”.
3. Press and hold the multi-information display switch for approximately 2 seconds or more to display “AVG UNIT”.
4. Lightly press the multi-information display switch to select the units.
5.  Press and hold the multi-information display switch for approximately 2 seconds or more to change the setting to the selected unit.

NOTE

• The display units for the driving range, the average fuel consumption, the average speed and the momentary fuel consumption are switched, but the units for the indicating needle (speedometer), the odometer, and the trip meter will remain unchanged.

The distance and speed units are also switched in the following combinations to match the selected fuel consumption unit.

Fuel consumption	Distance (driving range)	Speed (average speed)
L/100 km	km	km/h
mpg (US)	mile(s)	mph
mpg (UK)	mile(s)	mph
km/L	km	km/h
Changing the temperature unit

Changing the temperature unit
The display unit for temperature can be switched.

1. Press and hold the multi-information display switch for approximately 2 seconds or more to switch from the setting mode screen to the menu screen.
2. Lightly press the multi-information display switch to select “ ” (temperature unit setting).
3. Press and hold the multi-information display switch for approximately 2 seconds or more to switch in from °C to °F, or from °F to °C.
   The setting is changed to the selected temperature unit.

NOTE

• The temperature value on the air conditioning panel is switched in conjunction with the outside temperature display unit of the multi-information display.
  However, “°C” or “°F” are not shown on the temperature display of air conditioning.

Changing the display language
The language of the multi-information display can be switched.

1. Press and hold the multi-information display switch for approximately 2 seconds or more to switch from the setting mode screen to the menu screen.
   Refer to “Changing the function settings”.
2. Lightly press the multi-information display switch to select LANGUAGE” (language setting)
3. Press and hold the multi-information display switch for approximately 2 seconds or more to display “LANGUAGE”
4. Lightly press the multi-information display switch to select the desired language.
5. If you hold down the multi-information display switch for approximately 2 seconds or more, the setting is changed to the selected language.

NOTE

• If “—” is selected in the language setting, a warning message is not displayed when there is a warning display or interrupt display.

Operation sound setting

You can turn off the operation sounds of the multi-information display switch and rheostat illumination button.

1. Press and hold the multi-information display switch for approximately 2 seconds or more to switch from the setting mode screen to the menu screen.
   Refer to “Changing the function settings”.
2. Lightly press the multi-information display switch to select “ ” (operation sound setting).
3. Press and hold the multi-information display switch for approximately 2 seconds or more to switch from ON (operation sound on) to OFF (operation sound off), or from OFF to ON.
   The setting is changed to the selected condition.

NOTE

• • The operation sound setting only deactivates the operation sound of the multi-information display switch and rheostat illumination button. The warning display and other sounds cannot be deactivated.

Changing the time until “REST REMINDER” is displayed
The time until the display appears can be changed.

1. Press and hold the multi-information display switch for approximately 2 seconds or more to switch from the setting mode screen to the menu screen. Refer to “Changing the function settings”.
2. Lightly press the multi-information display switch to select “ALARM” (rest time setting).
3. Press and hold the multi-information display switch for approximately 2 seconds or more to display “ALARM”.
4. Lightly press the multi-information display switch to select the time until the display.
5. Press and hold the multi-information display switch for approximately 2 seconds or more, and the setting is changed to the selected time.

NOTE

• The drive time is reset when the ignition switch is turned off or the operation mode is put in OFF.

Changing the turn-signal sound
It is possible to change the turn-signal sound.

1. Press and hold the multi-information display switch for approximately 2 seconds or more to switch from the setting mode screen to the menu screen.
2. Lightly press the multi-information display switch to select (changing the turn-signal sound).
3. Press and hold the multi-information display switch for approximately 2 seconds or more to switch from 1 (turn-signal sound 1) to 2 (turn-signal sound 2), or from 2 to 1.
   The setting changes to the selected turn-signal sound.

Changing the momentary fuel consumption display
It is possible to change the bar graph setting of the momentary fuel consumption display.

1. Press and hold the multi-information display switch for approximately 2 seconds or more to switch from the setting mode screen to the menu screen.
   Refer to “Changing the function settings”.
2. Lightly press the multi-information display switch to select (changing the momentary fuel consumption display).
3. Press and hold the multi-information display switch for approximately 2 seconds or more to switch from ON (with the green bar graph) to OFF (without the green bar graph), or from OFF to ON. The setting changes to the selected bar graph setting.

Returning to the factory settings
Many of the function settings can be returned to their factory settings.

1. Press and hold the multi-information display switch for approximately 2 seconds or more to switch from the setting mode screen to the menu screen.
2. Lightly press the multi-information display switch to select “RESET” (returning to the factory settings).
3. When you press and hold the multi-information display switch for approximately 5 seconds or more, the buzzer sounds and all of the function settings are returned to the factory settings.

NOTE

• The factory settings are as follows.
  • Average fuel consumption and average speed reset mode: A (Auto reset)
  • Fuel consumption display unit: L/100 km
  • Temperature unit: °C (Celsius)
  • Display language: ENGLISH or RUSSI-AN
  • Operation sounds: ON (Operation sounds on)
  • “REST REMINDER” display: OFF
  • Turn-signal sound: Turn-signal sound 1
  • Momentary fuel consumption with the green bar graph: ON

FAQs

Useful Links

View Full PDF: 2020 Mitsubishi L200 Owner’s Manual| Auto User Guide

2024 Mitsubishi ECLIPSE CROSS Specs, Price, Features, Mileage (Brochure)

Indicators and Warning Lights: 2020 Mitsubishi L200 Guide