Instrument Cluster: 2019 Mitsubishi L200 Multi-mode display Guide

Instrument Cluster: 2019 Mitsubishi L200 Multi-mode Display Guide

The 2019 Mitsubishi L200’s instrument cluster is an advanced, multipurpose display that provides a thorough overview of crucial vehicle data. This multi-mode display, which blends appearance and utility to provide a user-friendly interface for monitoring many aspects of the vehicle’s performance, was designed with modern drivers in mind. The instrument cluster functions as the driver’s primary information center, providing information on anything from speed and fuel levels to navigation and entertainment options. Its clear graphics and simple layout make it easy to read at a glance, improving the driving experience as a whole. The 2019 Mitsubishi L200’s instrument cluster, with its advanced technologies and adjustable settings, raises the bar for vehicle equipment. This display gives drivers information and controls whether they are driving on city streets or rough terrain, ensuring a safe and pleasurable trip every time.

2024 Mitsubishi ECLIPSE CROSS Specs, Price, Features, Mileage (Brochure)

Instruments Mitsubishi L200

1. Tachometer
   The tachometer indicates the engine speed (r/min). The tachometer helps you to obtain more economical driving and also warns you of excessive engine speeds (Red zone).
2. Multi-information display ® 
3. Speedometer (km/h or mph + km/h)
4. Multi-information display switch

CAUTION

• When driving, watch the tachometer to make sure that the engine speed indication does not rise into the red zone (excessive engine rpm).

Multi-information display

Always stop the vehicle in a safe place before operating.
The following information is included on the multi-information display: odometer, tripmeter, average fuel consumption etc.

1. Engine coolant temperature display ®
2. Selector lever position display* ®
3. Speed limiter display* ®
4. Gearshift indicator* ® 
5. Fuel remaining display ®
6. Frozen road warning* ®
7. Information display ®
8. Service reminder ®

NOTE

• When the ignition switch or the operation mode is OFF, the speed limiter display, gear-shift indicator, selector lever position display, fuel remaining display, engine coolant temperature display and frozen road warning are not displayed.

2019 Mitsubishi L200 Information display 

Each time you lightly press the multi-information display switch (A), the display switches in the following order.

1. Odometer ®
2. Tripmeter ® 
3. Tripmeter 
4. Meter illumination control ® 
5. Driving range display ®
6. Average fuel consumption display
7. Auto Stop & Go monitor* ®
8. Outside temperature display*
9. Service reminder (distance) ®
10.  Service reminder (month) ®

NOTE

• When the ignition switch or the operation mode is OFF, the driving range display, average fuel consumption display and outside temperature display are not displayed.
   
• While driving, the service reminder is not displayed even if you operate the multi-information display switch.

Odometer

The odometer indicates the distance travelled.

Tripmeter

The trip meter indicates the distance travelled between two points.
Example usage of trip meter A and trip meter B.

It is possible to measure two currently travelled distances, from home using trip meter A and from a particular point on the way using trip meter B.

To reset the trip meter
To return the display to 0, hold down the multi-information display switch for about 2 seconds or more. Only the currently displayed value will be reset.

Example

If trip meter A is displayed, only trip meter A will be reset.

NOTE

• When disconnecting the battery terminal, the memory of trip meters A  and B are cleared, and the display returns to “0”.

Meter illumination control
Each time you press and hold the multi-information display switch (2) for about 2 seconds or more, there is a sound and the brightness of the instruments changes.

1. Brightness level
2. Multi-information display switch

NOTE

• You can adjust to 8 different levels respectively for when the position lamps are illuminated and when they are not.
  Each time you reduce two brightness levels, the segment display of the brightness level decreases one by one.
• If the vehicle is equipped with the automatic lamp control, when the lamp switch is in a position other than the “OFF” position, the meter illumination switches automatically to the adjusted brightness, depending on the brightness outside the vehicle.
• The brightness level of the instruments is stored when the ignition switch is turned off.

Driving range display
This displays the approximate driving range (how many more kilometres or miles you can drive). When the driving range falls below approximately 50 km (30 miles), “—” is displayed.

NOTE

• The driving range is determined based on the fuel consumption data. This may vary depending on the driving conditions and habits. Treat the distance displayed as just a rough guideline.
• When you refuel, the driving range display is updated.
  However, if you only add a small amount of fuel, the correct value will not be displayed. Fill with a full tank whenever possible.
• On rare occasions, the value displayed for the driving range may change if you are parked on an extremely steep incline. This is due to the movement of fuel in the tank and does not indicate a malfunction.
• The display setting can be changed to the preferred units (km or miles).

Average fuel consumption display
This displays the average fuel consumption from the last reset to the present time.
The reset mode conditions for the average fuel consumption display can be switched between “Auto-reset” and “Manual reset”. For information on how to change the average fuel consumption display setting.

NOTE

• The average fuel consumption display can be reset separately for the auto reset mode and for the manual reset mode.
  “—” is displayed when the average fuel consumption cannot be measured.
• The initial (default) setting is “Auto reset mode”.
• The average fuel consumption depends on the driving condition (road condition, driving behaviour, etc.). The displayed fuel consumption may vary from the actual fuel consumption. Treat the fuel consumption displayed as just a rough guideline.
• The memory of the auto reset mode or manual reset mode for the average fuel consumption display is erased if the battery is disconnected.
• The display setting can be changed to the preferred units {km/L, L/100 km, mpg}. 

Auto Stop & Go monitor
The accumulated time the engine has been stopped by Auto Stop & Go (AS&G) system is displayed.
Refer to “Auto Stop & Go (AS&G) system”

NOTE

• When the ignition switch or the operation mode is ON again, the accumulated time will be reset.

Outside temperature display
This shows the temperature outside the vehicle.

NOTE

• The display setting can be changed to the preferred units (°C or°F).
  Refer to “Changing the function settings”
   
• Depending on factors such as the driving conditions, the displayed temperature may vary from the actual outside temperature.

Frozen road warning
If the outside air temperature drops below approx. 3 °C (37 °F), the alarm sounds and the outside air temperature warning symbol (A) flashes for about 10 seconds.

CAUTION

• There is a danger the road might be icy, even when this symbol is not flashing, so please take care when driving.

Engine coolant temperature display

This indicates the engine coolant temperature.
If the coolant becomes hot, “
” will blink.
Pay careful attention to the engine coolant temperature display while you are driving.

CAUTION

• If the engine is overheating, “
  ” will blink. In this case, the bar graph is in the red zone. Immediately park the vehicle in a safe place and take the required measures. Refer to “Engine overheating”

Fuel remaining display

The fuel remaining display indicates the fuel level in the fuel tank when the ignition switch is ON.

• 1- Full
• 0- Empty

NOTE

• It may take several seconds to stabilise the display after refilling the tank.
• If fuel is added with the ignition switch is ON, the fuel gauge may incorrectly indicate the fuel level.
• The fuel lid mark (A) indicates that the fuel tank filler door is located on the left side of the vehicle.

Fuel remaining warning display

If the remaining fuel level is approximately 10 litres or less (one segment displayed) when the ignition switch is turned to the “ON” position, the last segment of the fuel gauge flashes. If the remaining fuel level is reduced further, the last segment of the fuel gauge goes out and “
” flash.

CAUTION

• Do not drive with an extremely low fuel level; running out of fuel could cause damage to the fuel system.

NOTE

• On inclines or curves, the display may be incorrect due to the movement of fuel in the tank.

Service reminder
Displays the approximate time until the next periodic inspection that MITSUBISHI MOTORS recommends.“—” is displayed when the inspection time has arrived.
The spanner mark indicates the periodic inspection.

NOTE

• Depending on the vehicle specifications, the displayed time until the next periodic inspection may differ from what MITSUBISHI MOTORS recommends.
  In addition, the display settings for the next periodic inspection time can be modified. To modify the display settings, have it adjusted at an MITSUBISHI MOTORS Authorized Service Point.
  For more details, contact an MITSUBISHI MOTORS Authorized Service Point.

1. Displays the time until the next periodic inspection.
   NOTE
   The distance is shown in units of 100 km (100 miles). The time is shown in units of months.
2. This informs you that a periodic inspection is due. Please consult an MITSUBISHI MOTORS Authorized Service Point.
3. After your vehicle is inspected at an MITSUBISHI MOTORS Authorized Service Point, it displays the time until the next periodic inspection.

To reset
The “—” display can be reset while the ignition switch is in OFF.

1. When you lightly press the multi-information display switch a few times, the information display switches to the service reminder display.
2. Press and hold the multi-information display switch for about 2 seconds or more to make the spanner mark start flashing.(If there is no operation for about 10 seconds with flashing, the display will revert to its original indication.)
3. Lightly press the multi-information display switch while the icon is flashing to change the display from “—” to “cLEAr”. After this, the time until the next periodic inspection will be displayed.

CAUTION

• The customer is responsible for making sure that periodic inspections and maintenance are performed.
  Inspections and maintenance must be performed to prevent accidents and malfunctions.

NOTE

• “—” display cannot be reset when the ignition switch is in ON.
• When “—” is displayed, after a certain distance and a certain period, the display is reset and the time until the next periodic inspection is displayed.
• If you accidentally reset the display, consult an MITSUBISHI MOTORS Authorized Service Point.

Changing the function settings
The “Average fuel consumption reset mode”, “Fuel consumption unit” and “Temperature unit” settings can be modified as desired when the ignition switch is ON.

CAUTION

• The driver should not operate the display while the vehicle is in motion.
• When operating the system, stop the vehicle in a safe area.

Changing the reset mode for average fuel consumption
The mode conditions for the average fuel consumption display can be switched between “Auto-reset” and “Manual reset”.

1. When you lightly press the multi-information display switch a few times, the information display switches to the driving range display.
2. Each time you press the informa-tion display switch for 2 seconds or more on the driving range display, you can switch to reset mode for average fuel consumption. (A: Auto reset mode, B: Manual reset mode)

Manual reset mode

• When the average fuel consumption is being displayed, if you hold down the multi-information meter switch, the average fuel consumption displayed at that time is reset.
• When the ignition switch is turned from the “ACC” or “LOCK” position to the “ON” position, the mode setting is automatically switched from manual to auto.

Auto reset mode

• When the average fuel consumption is being displayed, if you hold down the multi-information display switch, the average fuel consumption displayed at that time is reset.
• When the ignition switch is in the “ACC” or “LOCK” position for approxi-mately 4 hours or longer, the average fuel consumption display is automatically reset.

NOTE

• The average fuel consumption display can be reset separately for the auto reset mode and the manual reset mode.
• The memory of the auto reset mode or manual reset mode for the average fuel consumption display is erased if the battery is disconnected.
• The initial (default) setting is “Auto reset mode”.

Changing the fuel consumption display unit
The display unit for fuel consumption can be switched. The distance and amount of units are also switched to match the selected fuel consumption unit.

1. When you lightly press the multi-information display switch a few times, the information display switches to the average fuel consumption display.
2. Press and hold the multi-information display switch for about 5 seconds or more until the buzzer sound is heard twice.
3. Press and hold the multi-information display switch to switch in sequence from “km/L” → “L/100 km” → “mpg” → “km/L”.

NOTE

• The display units for the driving range, and the average fuel consumption are switched, but the units for the indicating needle (speedometer), the odometer, the trip meter and the service reminder will remain unchanged.
• The memory of the unit setting is erased if the battery is disconnected, and it returns automatically to the factory setting.

The distance units are also switched in the following combinations to match the selected fuel consumption unit.

Changing the temperature unit

The display unit for outside temperature can be switched. 

1. When you lightly press the multi-information display switch a few times, the information display switches to the outside temperature display.
2. Each time you press the multi informa-tion display switch for 2 seconds or more on the outside temperature display, you can switch from °C to °F or from °F to °C unit of the outside temperature display.

NOTE

• The temperature value on air conditioner panel is switched in conjunction with the outside temperature display unit of the multi-information display.
  However, “°C” or “°F” are not shown to the temperature display of an air conditioner.

FAQs

Useful Links

View Full PDF: 2019 Mitsubishi L200 Owner’s Manual| Auto User Guide

2024 Mitsubishi ECLIPSE CROSS Specs, Price, Features, Mileage (Brochure)

2019 Mitsubishi L200 Indicators And Warning Lights Meanings