2022 Renault Kangoo Owner’s Manual
With its adaptable styling and improved practicality, the 2022 Renault Kangoo represented a substantial advancement in the company’s lineup of light commercial vehicles, appealing to both individual and commercial consumers. With a redesigned exterior, an improved cargo capacity, and a more ergonomic and pleasant interior, the most recent Kangoo model stands out and is very useful for a range of personal and business uses. It meets the growing demand for environmentally responsible transportation by providing a selection of efficient engine options under the hood, including gasoline, diesel, and an electric variation. In addition, the car has a number of cutting-edge technological elements that make driving safer and more connected, such as an upgraded infotainment system and a number of safety assists. The 2022 Kangoo is a formidable competitor in the small van and multipurpose vehicle markets thanks to its innovative combination of technology, efficiency, and adaptability.
REAR SCREEN WASHER, WIPER
Activation/deactivation of the rear screen wiper
Engaging reverse gear triggers intermittent wiping (if the front wipers are in operation). If your vehicle is equipped with a vehicle settings customisation menu, you can opt to activate or deacti- vate this function. In the event of obstacles present on the rear window (dirt, snow, etc.), the wiper will try to sweep away all the obstacles. If an obstacle prevents the blade from moving, it can be stopped. Remove the obstacle, wait for around 30 seconds and reactivate the wiper using the wiper stalk.
Precautions
- In the event of ice, check that the blades are not stuck to the windscreen before operating the wipers. If you activate the wiper while the blade is blocked by ice, you risk damaging both the blade and the wiping motor.
- Do not operate the wipers on a dry screen. This will lead to premature wear or damage to the blades.
Rear screen wash/wipe
With the ignition on, push and hold stalk 1, then release. Holding the stalk for longer will trigger (in addition to the windscreen washer) two sweeps of the wipers followed, a few seconds later, by a third (drip wiping function). When the stalk is released, it returns to the rear wipe position.
TANK
Useable capacity of the tank: 12 gal (54 litres) approximately.
With the vehicle unlocked, to open cover 1, press area A then release. The cover 1 opens. Use the cap holder 2 on the flap 1 during filling to hold the cap 3 in place. For details on filling the fuel tank, refer to the information on “Filling with fuel”. To close it, press on the fuel filler flap by hand, as far as it will go.
Fuel grade
Use a high-grade fuel that complies with the legislation in force in each country and which must comply with the specifications given on the label on the cover 1.
Filler cap: this is specific.
If you have to replace it, make sure it is identical to the original cap. Contact an approved Dealer. Never place the cap near a source of heat or flame. Do not wash the filler area with a high-pressure washer. Do not mix even small amounts of petrol (un- leaded or E85) with diesel. Do not use ethanol-based fuel if your vehicle is not compatible with this fuel. Do not add reagent to the fuel – other wise you risk damaging the engine If you wish to add an additive to the fuel, use a product approved by our Technical Department. Consult an approved dealer.
Diesel version
It is essential to use diesel fuel that conforms with the information given on the label inside cover 1.
Petrol version
It is essential to use unleaded petrol. The octane rating (RON) must comply with the information given on the label on the cover 1.
Filling with fuel
With the ignition off, insert the nozzle and insert it fully before turning it on to fill the fuel tank (risk of splashing). Keep the nozzle in this position through- out the entire filling operation. When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts may be made, as there must be suffi-cient space in the fuel tank to allow for expansion. Make sure that no water enters the fuel tank during filling. The cover 1 and its surround must remain clean.
Special case
When the vehicle has been stopped for around three months, you must add fuel to prevent damage to the fuel pump. To do this, with the ignition off, top-up at least 1.10 gallons (5 litres) then start the engine to operate the pump and renew the fuel in the circuit. If it is not possible to add at least 1.10 gallons (5 litres) of fuel due to the fuel level in the tank, drive the vehicle until the tank has capacity.
Petrol version
Using leaded petrol will damage the antipollution system and may lead to a loss of warranty. To ensure that the fuel tank is not filled with leaded petrol, the fuel tank filler neck contains a restrictor fitted with a foolproof system which only allows the nozzle for unleaded petrol to be used (at the pump).
Running out of fuel on diesel versions
Vehicles with key/remote control
- Turn the ignition key 4 to the “On” position ON 2 and wait a few minutes before starting to allow the fuel circuit to be primed;
- turn the key to position START 3. If the engine does not start, repeat the procedure;
- If the engine does not start after several attempts, contact an approved dealer.
Vehicles with card
With the card in the passenger compartment, press the start button 5 without pressing any of the pedals. Wait a few minutes before starting. This will enable the fuel circuit to be primed. If the engine does not start, repeat the procedure. If the engine does not start after several attempts, please contact an authorised dealer. No modifications whatsoever are permitted on any part of the fuel supply system (electronic units, wiring, fuel circuit, injectors, protective covers, etc.) as this may be dangerous (unless undertaken by qualified Network personnel).
Persistent fuel odour
If you notice a persistent fuel odour you should:
- stop the vehicle as soon as traffic conditions allow and switch off the ignition;
- switch on the hazard warning lights and ask your passengers to leave the vehicle and stay clear of the traffic;
- contact an approved Dealer.
REAGENT TANK
Please ensure that you comply with the legislation of your country. It is important to remember that failure to respect regulations in force could lead to legal action being taken against the vehicle owner.
Operating principle
The reagent is intended for diesel engines fitted with the SCR (selective catalytic reduction) system. The use of reagents reduces exhaust emissions by transforming the pollutants into water vapour and nitrogen. Reagent consumption in real time depends on vehicle usage conditions, the equipment fitted, and driving style.
Reagent quality
Use only reagents which conform to standard ISO 22241 and in accordance with the mark on the tank filler cap.
Filling
Useable capacity of the tank: 3.74 gallons (17 litres) approximately. With the ignition switched off, open the cover A, then unscrew the cap.
Note: ammonium hydroxide vapour may escape from the cap opening when the tank temperature is high. To fill up with reagent, the engine must be stopped (and not only on standby in the case of vehicles equipped with the function) STOP and START: you must switch off the ignition If the “XXX miles (XXX km) lockout refill AdBlue” message appears, fill the rea- gent tank and refer to the filling instructions.
Risk of immobilisation of the vehicle.
Fuel filler cap: this is a specific type.
If you have to replace it, make sure it is identical to the original cap. Contact an ap-proved Dealer. Do not wash the filler area with a high pressure washer.
REAGENT TANK
Filling (continued)
The tank can be filled at the pump. With the ignition off, insert the nozzle fully before activating it to fill the fuel tank (risk of splashing). Keep the nozzle in this position throughout the entire filling operation.
When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts may be made, as there must be sufficient space in the fuel tank to allow for expansion.
In other filling cases, it is essential to read the information shown on the reagent container (e.g. the can or bottle).
Precautions for use
When filling:
- handle the reagent with care. They can damage clothes, shoes, bodywork components etc.;
- make sure that no water enters the fuel tank.
If the reagent overflows, or contami- nates any paintwork, clean the affected area quickly with plenty of cold water and a soft cloth.
Note: if the reagent crystallises, use a soft sponge.
In extreme cold weather conditions
In frosty weather conditions, the rea- gent tank should be refilled when the indicator and the message “TOP UP AdBlue before 1200 km” appear on the instrument panel.
Special cases
The reagent fluid freezes below about -10°C. In these conditions, do not attempt filling when the fluid is frozen. In the event of needing to top up or fill the tank with reagent (on), park the vehicle in a hotter location if possible so that the reagent becomes liquid again. Otherwise, have a qualified professional top up or fill up with reagent fluid. After filling the reagent tank, check that the cap and cover are closed, start the engine and WAIT 10 sec- onds with the vehicle stationary, engine running before setting off again. If this operation is not carried out, the filling of the tank will not be taken into account automatically until after several dozens of minutes of driving. The message “— TOP UP AdBlue” and/or the warning lights will con- tinue to appear until the filling has been registered by the system. No work whatsoever is permitted on any part of the system. To prevent damage, only qualified personnel from our network may work on the system.
Petrol version
For the first 600 miles (1,000 km), do not exceed 78 mph (130 km/h) in the highest gear, or 3,000 to 3,500 rpm. You may only expect top performance from your vehicle after approximately 1,800 miles (3,000 km).
Service intervals: refer to the Maintenance Document for your vehi-cle.
Diesel version
For the first 1,000 miles (1,500 km), do not exceed 80 mph (130 km/h) in the highest gear, or 2,500 rpm. After completing this mileage you may drive faster, although you may only expect top performance after approximately 3,600 miles (6,000 km). During the running in period, do not accelerate hard while the engine is still cold and do not let the engine over-rev. Service intervals: refer to the Maintenance Document for your vehicle.
Ignition switch
Off position LOCK 0 (steering lock applied)
- To lock: remove the key and turn the steering wheel until the steering column locks.
- To unlock: turn the key and the steering wheel slightly.
“Ignition” position ON 2
The ignition is switched on: Any accessories (radio etc.) can be used.
“Start” position START 3
If the engine fails to start at the first attempt, the key must be turned back before the starter can be activated again. Release the key as soon as the engine starts.
Note: on diesel versions, several seconds may pass between turning the key and the engine starting to allow for engine preheating.
Special features
- If any of the starting conditions are not met, the message “Press Brake + START” or “Press Clutch + START” or “Select Gearbox Position “P”” is displayed on the instrument panel;
- in some cases, it will be necessary to move the steering wheel whilst pressing the start button 3 to help unlock the steering column; the message “Turn Steering Wheel + START” will warn you of this;
Note: on vehicles equipped with a manual gearbox, in the event of engine stalling the message “Press Clutch” will be displayed on the instrument panel. Fully press the clutch pedal to restart the engine.
“Hands-free” starting with the tailgate open
In this case, the card should not be lo- cated in the luggage compartment, to prevent the risk of loss.
Accessories function
(switching on the ignition)
Once you have gained access to your vehicle, you may use some of its func- tions (radio, navigation, wipers, etc.). To use the other functions, with the card in the passenger compartment, press the 3 button without pressing the pedals.
Operating faults
In certain cases, the hands-free card may not work:
- when the card battery is dead;
- near to appliances operating on the same frequency as the card (monitor, mobile phone, video game, etc.);
- vehicle located in a high electromagnetic radiation zone.
The message “Place card on zone + START” appears on the instrument panel. Press the brake or clutch pedal, then place the card 5 (button side) on the placement area marked by the 4 symbol. Press the 3 button to start the vehicle. The message goes out.
Conditions for stopping the engine
The vehicle must be stationary, lever in position P on vehicles with an automatic gearbox. With the card in the vehicle, press button 3: the engine stops. The steer- ing column is locked when a door is opened or the vehicle is locked. If the card is no longer in the passen- ger compartment or if the card’s battery is worn, when the vehicle is stationary and you try to switch the engine off, the message “Keycard absent: press/ hold START” appears on the instrument panel: press button 3 for longer than two seconds. If the card is no longer in the passenger compartment, make sure you can retrieve it before press- ing and holding the button. Without the card, you will not be able to restart the vehicle. With the engine switched off, any ac-cessories being used (radio, etc.) will continue to function for approximately 10 minutes. When the driver’s door is opened, the accessories stop working. Never switch off the igni- tion before the vehicle has stopped completely. Once the engine has stopped, the brake servo, power-assisted steer- ing etc., and the passive safety de- vices such as the airbags and pre- tensioners will no longer operate.
Driver’s responsibility when parking or stopping the vehicle
Never leave an animal, child or adult who is not self-suffi- cient alone in your vehicle, even for a short time. They may pose a risk to themselves or to others by starting the engine, activating equipment such as the electric windows or locking the doors, for example. Also, in hot and/or sunny weather, please remember that the tempera- ture inside the passenger compartment increases very quickly. RISK OF DEATH OR SERIOUS INJURY.
Preventing the engine from standing by
In certain situations, such as negotiating a crossroads for instance, it is possible (with the system activated) to keep the engine running so as to be ready to move off quickly.
For vehicles equipped with automatic gearboxes and when the engine standby is performed only when the vehicle stopped:
Keep the vehicle stationary without pressing too hard on the brake pedal.
For vehicles equipped with manual gearboxes:
Keep the clutch pedal pressed right down.
Conditions preventing the standby of the engine
Certain conditions prevent the system from using the engine standby function, including when:
- the driver’s door is not closed;
- the driver’s seat belt is not fastened or was not fastened when driving began;
- reverse gear is engaged;
- the bonnet is not locked;
- the outdoor temperature is too low or too high;
- the battery is not sufficiently charged;
- the difference between the vehicle interior temperature and the auto- matic climate control instruction is too high;
- parking distance control is in operation;
- the altitude is too high;
- the slope is too steep for vehicles fitted with an automatic gearbox;
- the “Clear view” function is activated.
- the engine temperature is too low;
- the emission control system is being regenerated;
Warning light is displayed on the instrument panel. This notifies you that engine standby is not available.
The warning light may appear along with a message on the instrument panel:
- “Optimising Battery Recharge” to prioritise battery charging;
- “Prioritising Thermal Comfort” to prioritise air conditioning;
- “Prioritising running engine” to priori- tise engine operations.
FAQ
The Renault Kangoo is a light commercial vehicle, also popular as a compact multi-purpose van.
It offers a range of engines, including petrol, diesel, and an electric variant.
Yes, there is an electric version known as the Kangoo Z.E.
The Kangoo provides a generous cargo space, varying with the configuration and model (standard or extended).
Yes, there is a passenger version of the Kangoo, which is designed more for personal use.
The passenger version can typically seat up to five or seven people, depending on the configuration.
Safety features may include ABS, airbags, electronic stability control, and driver-assist systems like lane-keeping assist.
It is likely available with both manual and automatic transmission options.
Yes, it includes modern infotainment systems with touchscreen interfaces, Bluetooth connectivity, and potentially navigation systems.
Yes, the cargo area is adaptable and can be fitted with various shelving and storage solutions.
Yes, sliding side doors are typically available for easy access.
Fuel efficiency varies by engine type, but both the petrol and diesel variants are designed for economy, and the electric version offers zero emissions.
Roof racks and other external storage solutions are available as optional accessories.
The warranty varies by region but generally includes a standard manufacturer’s warranty.
Its compact size and efficient engines make it well-suited for city driving and manoeuvring in tight spaces.
Useful Link