2023 Renault Capture Headlights and Wipers Guide
The 2023 Renault Captur stands out as a remarkable blend of style, innovation, and functionality in the realm of current automobile design. The Headlights and Wipers systems stand out as pillars of safety, convenience, and aesthetics among its many notable features. These technologies not only illuminate the road ahead, but also ensure crystal-clear visibility in varying weather situations, making every journey a more comfortable and secure experience.
The headlights and wipers on the 2023 Renault Captur are more than simply practical features; they are essential to the vehicle’s dedication to providing a superb driving experience. LED headlights contribute to a more sustainable drive by reducing power consumption and environmental effect, in addition to their brightness and efficiency. Meanwhile, rain-sensing wipers prevent water waste, which aligns with the eco-conscious driving approach. The 2023 Renault Captur’s Headlights and Wipers represent the brand’s commitment to merging cutting-edge technology with environmental responsibility in this era of intelligent mobility.
HEADLIGHT BEAM ADJUSTMENT
Switch A is used to adjust the height of the headlight beams according to the load.
With the dipped beam headlights lit, press or lift switch A as many times as is necessary to select the required position on the instrument panel.
Note: depending on the vehicle, when the engine is started, the position selected is displayed on the instrument panel for approximately 30 seconds and for 5 seconds each time switch A is pressed.
| Examples of positions for adjusting control A according to the load | |
| Driver alone or with front passenger | 0 |
| All seats occupied | 1 |
| Driver with passengers and luggage (or load) reaching the maximum permissible all-up weight | 3 |
| Driver without passengers and luggage (or load) reaching the maximum permissible all-up weight | 4 |
Depending on the Vehicle
The table below gives some examples. In all cases, adjust control A according to the vehicle load so that the road can be seen and other drivers are not dazzled.
WINDSCREEN WASH, WIPE)
Vehicle fitted with intermittent windscreen wipers
A park
B intermittent wiping
The wipers will pause for several seconds between sweeps. It is possible to change the time be-tween sweeps by turning ring 2.
C normal wiping speed
D fast wiping speed
Special Note
When driving the vehicle, the wiping speed slows down whenever the vehicle stops. For example, fast wiping speed will slow to normal wiping speed. As soon as the vehicle moves off, wiping will return to the speed originally selected.
If stalk 1 is operated, it overrides and cancels the automatic function.
For all vehicles, position C can be accessed with the ignition on and positions B and D can only be accessed with the engine running.
Vehicle fitted with front windscreen wiper rain sensor
The rain sensor is located on the windscreen, in front of the interior rear-view mirror.
- A single sweep
A short push will trigger one sweep of the wipers. - B stop
C automatic wiper function
When this position is selected, the system detects water on the wind-screen and triggers the wipers at a suitable wiping speed. It is possible to change the triggering thresh-old and the time sweeps by turning ring 2:
- F : minimum sensitivity
- G : maximum sensitivity
The higher the sensitivity, the quicker the wipers will react and the faster the wipe.
When activating automatic wiping or when increasing sensitivity, one sweep of the blades is performed.
Note
- The rain sensor is only intended as a driving aid. In the event of reduced visibility, the driver should manually activate the wipers. In foggy weather or during snowfalls, wiping is not automatically triggered and remains under the driver’s control;
In the event of temperatures below zero, automatic wiping is not activated when the vehicle is started. It is automatically activated as soon as the vehicle exceeds a certain speed (approximately 5 mph (8 km/h)); - Do not activate automatic wiping in dry weather;
- Fully de-ice the windscreen before activating automatic wiping.
Operating Faults
In the event of a malfunction of the automatic wiping, the wiper is set to intermittent wiping. Contact an authorised dealer.
The operation of the rain sensor can be disturbed in the event of:
Damaged wiper blades; a screen of water or traces left by a blade in the sensor’s detection zone may increase the response time of the automatic wiper, or increase the wiping frequency;
A windscreen with any chip or crack level with the sensor, or a windscreen covered in dust, dirt, insects, ice, the use of washing wax and water-repellent chemicals; the automatic wiping will be less sensitive, or even unresponsive.
- D slow continuous wiping
E fast continuous wiping
Special Note
When driving the vehicle, the wiping speed slows down whenever the vehicle stops. For example, fast wiping speed will slow to normal wiping speed. As soon as the vehicle moves off, wiping will return to the speed originally selected.
If stalk 1 is operated, it overrides and cancels the automatic function.
Precautions
- In the event of ice, check whether the blades are stuck to the windscreen before operating the wiping mechanism. If you activate the wipers while the blades are stuck down with ice, you may risk damaging both the blade and the wiper motor.
- Do not activate the wipers on a dry screen. This will lead to premature wear or damage to the blades.
Specific front wiper position (service position)
This position enables the blades to be lifted to remove them from the windscreen.
This can be useful:
- To clean the blades;
To release the blades from the windscreen in winter;
Replace the blades
With the ignition on or engine started, lift the stalk twice 1 to position A (single sweep). The blades stop slightly away from the bonnet.
To return the blades to low position, with the ignition on, ensure that the wipers have folded down onto the wind- screen, then move the stalk 1 to position A (single sweep).
Before switching on the ignition, place the wipers on the windscreen. Otherwise, there may a risk of damage to the bonnet or the wipers when they are switched on.
Before any action involving the windscreen (washing the vehicle, deicing, cleaning the windscreen, etc.) return stalk 1 to position B (stop). Risk of injury and/or damage.
In the event of obstacles on the windscreen (dirt, snow, ice etc.), clean the windscreen (including the central area located behind the interior rear view mirror) before starting the wipers (risk of motor overheating).
If an object is preventing a blade from moving, it may stop functioning. Remove the obstacle and reactivate the wiper using the wiper stalk.
Windscreen Washer
With the ignition on, pull stalk 1 then release.
A longer pull will trigger, in addition to the windscreen washer, two sweeps of the wipers followed, a few seconds later, by a third.
On vehicles fitted with a multimedia screen, you can choose to activate or disable the third sweep of the blades.
Note:
In temperatures below zero, the washer liquid risks freezing to the windscreen, thereby reducing visibility. Heat the windscreen using the demister control before cleaning.
When working in the engine compartment, ensure that the windscreen wiper stalk is in position B (stop).
Efficiency of a wiper blade
Check the condition of the wiper blades. How long they last depends on you:
- It must remain clean: clean the blade and the screen regularly with soapy water;
Do not use it when the screen is dry; - Free it from the screen when it has not been used for a long time.
In all cases, replace it as soon as it begins to lose efficiency: approximately once a year.
Precaution for using the wipers
- In freezing or snowy weather conditions, clear the screen before starting the wipers (risk of motor overheating);
Ensure that no objects are obstructing the travel of the blade.
-
REAR SCREEN WASHER, WIPER
Rear Screen Wiper
With the ignition on, turn ring 3 on stalk 1 to align the symbol with mark 2.
Stop;
Intermittent wiping.
The wipers will pause for several seconds between sweeps. Wiping frequency varies with vehicle speed;
-
- Sow continuous wiping.
To stop the operation, pivot ring 3 again.
Note
When washing using a roller type car wash, return the ring 3 on the stalk 1 to the stop position to deactivate automatic wiping.
Follow usage recommendations.
Do not use the wiper arm to open or close the tailgate.
Before any action involving the rear screen (washing the vehicle, de-icing, cleaning, etc.) return stalk 1 to the stop position.
Efficiency of a Wiper Blade
Check the condition of the wiper blades. How long they last depends on you:
- It must remain clean: clean the blade and the screen regularly with soapy water;
Do not use it when the screen is dry;
Free it from the screen when it has not been used for a long time.
In all cases, replace it as soon as it begins to lose efficiency: approximately once a year.
Precaution for using the wipers
- In freezing or snowy weather conditions, clear the screen before starting the wipers (risk of motor overheating);
Ensure that no objects are obstructing the travel of the blade.
Activation/deactivation of the rear screen wiper
Engaging reverse gear triggers intermittent wiping (if the front wipers are in operation). If your vehicle is equipped with a vehicle settings customisation menu, you can opt to activate or deactivate this function.
For vehicles not fitted with a settings customisation menu, you can have this function deactivated by an authorised dealer.
In the event of obstacles present on the rear window (dirt, snow, etc.), the wiper will try to sweep away all the obstacles. If an obstacle prevents the blade from moving, it can be stopped. Remove the obstacle, wait for around 30 seconds and reactivate the wiper using the wiper stalk.
Precautions
- In the event of ice, check that the blades are not stuck to the wind- screen before operating the wipers. If you activate the wiper while the blade is blocked by ice, you risk damaging both the blade and the wiping motor.
Do not operate the wipers on a dry screen. This will lead to the premature wear or damage to the blades.
Rear Screen Wash/Wipe
With the ignition on, push and hold stalk 1, then release.
Holding the stalk for longer will trigger (in addition to the windscreen washer) two sweeps of the wipers followed, a few seconds later, by a third (drip wiping function).
When the stalk is released, it returns to the rear wipe position.
FAQs
Simply twist the headlight switch on the left side of the steering column to turn on the headlights. The first setting is for parking lights, while the second is for full headlights.
Yes, the 2023 Renault Captur has automatic headlights that vary brightness dependent on ambient light conditions.
To activate the high beams, push the turn signal stalk away from you. Return to low beams by pulling it back.
Yes, the Renault Captur has automatic headlights that detect low-light conditions and turn on or off accordingly.
To control the windshield wipers, use the stalk on the right side of the steering column. Push it up to do a single wipe, down to perform intermittent wipes, and even lower to perform continuous wipes.
Yes, you can change the speed of the wipers by twisting the ring at the end of the wiper stalk. This lets you choose the desired wiper speed.
To activate the windshield washer, pull the wiper stalk nearer you. This sprays washer fluid onto the windshield while also activating the wipers to clear the glass.
It’s possible that worn wiper blades are causing your wipers to make noise or stop working properly. For best results, replace the blades as needed.
To activate the windshield washer, pull the wiper stalk nearer you. This sprays washer fluid onto the windshield while also activating the wipers to clear the glass.
You may regulate the intensity of the wiper spray by moving the dial on the wiper stalk to control the amount of washer fluid applied.
There is, indeed, a back windshield wiper. A separate switch on the dashboard controls it.
Turn on the rear wiper switch on the dashboard. The rear wipers can be operated intermittently or continuously.
Headlights and wipers are typically considered wear-and tear equipment and may be excluded from the regular vehicle warranty. It is critical to review your warranty terms for coverage information.
The owner’s manual for your vehicle has detailed instructions for replacing headlight bulbs and wiper blades. If you are unsure, it is best to get advice from a qualified Renault service center.
Useful Link
View Full PDF: Renault Capture 2023 User Manual| Auto User Guide