2023 Renault Zoe Display Setting | Screen Messages Guide

2023 Renault Zoe Display Setting | Screen Messages Guide

In 2023, Renault Zoe’s display settings underwent a notable evolution, heralding a paradigm shift in user interface design within the electric vehicle landscape. With a focus on enhancing user experience and accessibility, Renault introduced an array of screen messages that not only provided vital information but also transformed mundane interactions into engaging experiences. Seamlessly integrating advanced technology, Zoe’s display settings became a canvas for innovation, offering drivers a personalized journey through an intuitive interface. From succinct notifications to intricate navigation prompts, every message was meticulously crafted to streamline interactions while maintaining a sense of elegance and sophistication. This meticulous attention to detail not only elevated the driving experience but also underscored Renault’s commitment to pushing the boundaries of automotive design. As drivers embarked on their journeys, they were greeted by a symphony of digital cues, each tailored to anticipate their needs and facilitate effortless navigation. Through this comprehensive overhaul, Renault Zoe’s display settings transcended mere functionality, emerging as a testament to the transformative power of thoughtful design in shaping the future of mobility.

2023 Renault Traffic Specs, Price, Features, Mileage and Review

DISPLAYS AND INDICATORS

The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY.

You may customise your instrument panel A with content and colours of your choice.
Press the switch 1 repeatedly to obtain the desired display.
Charge meter 2
Please refer to the information on the “Charge meter” in Section 2.

Message indicating vehicle ready for driving 3
The message READY comes on when the engine is started.

Speedometer 4
Vehicle speed is limited to approxi-mately 80 mph (135 km/h).
Indicator of charging programming and/or air conditioning 5

On-board computer display

Please refer to the information on the “Trip computer: general information” in Section 1.

Instrument panel in miles
It is possible to switch to km/h.
On the multimedia display, select “Menu”, “System ”, “System settings ”, “Set units ” and confirm. To return to the previous mode, repeat the same operation.

Estimated range
Remaining charge time
from about 95% charge, the remaining charge time is no longer displayed.

Opening element warning light
Shows when a door, the tailgate or charging flap is open or not closed properly.

Traction battery charge load
Charging cable “Plugged In” warning light 11
This comes on when the charging cord is plugged into the vehicle.

Charge level
The gauge indicates the level of energy remaining.

Reserve level
This means the traction battery charge has reached approximately 7% or, depending on the vehicle, approximately 12%. The 14 warning light comes on and a beep sounds. The charge level 12 and range 7 turn to orange. To optimise your range, please see the information on “Recommendations: saving energy” in Section 2.

Immobilisation threshold imminent
When the charge level reaches 4.5% or, depending on the vehicle, approxi-mately 6%, a beep is heard and the
warning light 14 flashes. When the charge level reaches 3.5% or, depending on the vehicle, approxi-mately 5%, the range value is no longer displayed. Motor performance gradually decreases until the vehicle comes to a stop.
Refer to the information on “Towing” in Section 5.

TRIP COMPUTER: general information

Trip computer 1
Depending on the vehicle, this includes the following functions:

• distance travelled;
• journey parameters;
• information messages;
• operating fault messages (con-nected to the warning light );
• warning messages (connected to the warning light).

All these functions are described on the following pages.

Display selection keys 2 and 3
Scroll through the following information upwards (key 2) or downwards (key 3) by pressing briefly and successively (the display depends on the vehicle equipment and country).

• total mileage and trip mileage recorder;
• journey parameters:
  • current energy consumption; total energy consumption and distance travelled since the last reset;
  • average energy consumption and average speed.
• service interval;
• tyre pressure reset;
• trip log, operating faults and informa-tion message readout;
• depending on the vehicle and only when stopped, settings customisation menu:
  • clock;
  • language;
  • automatic locking of the doors while driving;
  • rear windscreen wiping in reverse gear;
  • switching off the instrument panel when charging;
• depending on the vehicle and only when stopped, programming menu:
  • charging; activation and setting the start time;
• Air conditioning; activation and setting the start time.

  

Trip mileage resetting
With “trip mileage recorder” selected on the display, press the button 2 or 3 until the mileage recorder resets to zero.

Resetting the journey parameters (reset button)
with the display showing one of the journey parameters, press button 2 or 3 until the display is reset.

Automatic resetting of the journey parameters
Resetting occurs automatically when the maximum value of any of the parameters is exceeded.

Reading energy consumption values
Some vehicle equipment items consume energy: the energy consumed by the vehicle may therefore differ from the energy consumed on the electric counter.

Interpreting some of the values displayed after resetting
The values showing average energy consumption and average speed will become more stable and reliable the further you have travelled since the last time the Reset button was pressed.

Resetting the estimated range
After a full recharge of the traction bat-tery, you can select two types of resetting: manual or automatic.

Manual reset
With one of the trip parameters selected on the display, press and hold one of buttons 2 or 3 to reset the range.

Automatic reset
The range is automatically reset at the end of a full recharge of the traction battery to a value calculated based on the energy consumption over the last 125 miles (200 km).

Some on-board computer information appears on the navigation system display.
Resetting the mileage recorder, the trip settings, etc. is done simultaneously on the on-board computer and the navigation system.

ON-BOARD COMPUTER: trip settings

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Examples of selections	interpreting the display selected
101778 km 112.4 km  Totals 20 kWh 522 km Averages 14,6 kWh/100km 48 km/h Direct consump’n  12 kW	Total mileage and trip mileage recorder.  Journey parameters.   Energy consumed since the last reset. Distance travelled since the last reset. From last reset. Average energy consumption. The value is displayed after having travelled at least 400 metres since the last reset. Average speed since the last reset. The value is displayed after driving 400 metres. Current energy consumption.

Examples of selections	interpreting the display selected
Service in 1,210 miles or 3 months	Service interval. Distance remaining until the next service (displayed in miles/kilometres), then when the service nears, several scenarios are possible: distance/time remaining less than 900 miles (1,500 km) or one month: the message “Service in” is displayed accompanied by the distance or time; imminent service: the message “Schedule a service” is displayed, accompanied by the nearest term (distance or time); mileage before service equal to 0 km/miles or service date reached: the message “Carry out service” is displayed accompanied by warning light ©. The vehicle requires a service as soon as possible.
resetting the display after the service in accordance with the maintenance schedule. The service interval must only be reset after a service which complies with the recommendations in the maintenance schedule. Special note To reset the service interval, press and hold one of the display reset buttons for approximately 10 seconds until the display shows the mileage permanently.

Examples of selections	interpreting the display selected
LEARNING THE TYRE PRESSURE  Passenger airbag off	reset the tyre pressure. Please refer to the information on the “Tyre pressure loss warning” in Section 2. Trip log Successive display: information messages; operating fault messages.

TRIP COMPUTER AND WARNING SYSTEM: information messages
These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages.

Examples of messages

interpreting the display selected

Disconnect cable to start up Please insert keycard The steering wheel not locked Apply brakes» Check connections Check charging post» Power cut while charging Charging refused no contract

This indicates that the charging cord is still plugged into the vehicle. Indicates that the cardRENAULT is not in the reader. This indicates that the steering column has not been locked. Follow these instructions: risk of damage to the motor. Unplug, then plug in the vehicle. If the message still shows, this may be caused by the external charging conditions or by the home installation. Indicates a possible electrical fault or a defective charging cable: change the charging terminal or location or have the cable checked. Indicates an electrical fault while charging. Restart charging. If this does not work, have the electrical installation checked. Charging is prohibited by your battery rental organisation. Rectify the situation.

TRIP COMPUTER AND WARNING SYSTEM: operating fault messages
These appear with the
warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle.
They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The
warning light stays on. Examples of operating fault messages are given in the following pages.

Examples of messages	interpreting the display selected
Check airbag	Indicates a fault in the restraint system in addition to the seat belts. In the event of an accident, it is possible that they may not be triggered.
Elec. System to check	Indicates a fault on one of the pedal sensors or in the 12 V battery management system.
Check braking system	Indicates wear or the need to check the braking system.
vehicle plug to be checked	Indicates overheating at the vehicle-side charging socket. Wait for about 20 minutes and try again. If this does not work, contact an authorised dealer.
Elec. System to check»	Indicates a fault in the traction system.
Always charging»	Indicates a fault on the traction battery recharge system.

TRIP COMPUTER AND WARNING SYSTEM: warning message
These appear with the warning light
and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an Authorised Dealer.
Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.

Examples of messages	interpreting the display selected
Braking system fault Power steering fault Electrical motor fault Electrical fault danger “ PUNCTUrE “	Indicates a fault in the braking system. Indicates a fault in the steering. Indicates that the vehicle is losing power. Indicates a fault in the electric system. Indicates that at least one wheel is punctured or severely underinflated.

FAQs

Useful Links

View Full PDF: Renault Zoe 2023 User Manual|Auto User Guide

2023 Renault Traffic Specs, Price, Features, Mileage and Review

2023 Renault Zoe Replacing Fuses | Fuse Diagrams Guide