Subaru Legacy 2023 Steering Responsive Headlight (SRH) And Wiper And Washer Touring XT
The Subaru Legacy 2023 is a midsize sedan that provides an array of features to ensure a comfortable and secure driving experience, including advanced steering, headlight, and wiper systems. The Touring XT trim of the Legacy 2023 includes additional features like adaptive LED headlights, a heated steering wheel, and a windshield wiper de-icer. This guide will answer frequently asked questions about the Subaru Legacy 2023 steering, headlight, and wiper systems, such as their advantages, how to use them, and the best maintenance tips. We’ll also discuss the extra features that come with the Touring XT trim level.
2024 Subaru Legacy Specs, Price, Features, Mileage (Brochure)
Steering Responsive Headlight (SRH)
- The target area of illumination when SRH is activated.
- The target area of illumination when SRH is not activated.
SRH is a function that automatically moves the headlight beam to the left or right in accordance with the steering angle and vehicle speed. This function helps to improve visibility at night by illuminating the road ahead at corners and intersections.
You can turn the SRH function on or off. The settings can be changed by using the center information display. 
SRH OFF indicator light
The SRH OFF indicator light on the combination meter turns off when SRH is turned on.
SRH warning indicator
If SRH is malfunctioning, the SRH OFF indicator light on the combination meter flashes when the ignition switch is in the “ON” position. It indicates that SRH has been deactivated. Contact a SUBARU dealer for an inspection.
NOTE
- If you turn the ignition switch to the “OFF” position with SRH turned off and then start the engine again, SRH will automatically turn on.
- When you turn the ignition switch to the “ON” position, the SRH OFF indicator light will illuminate and turn off after several seconds.
- SRH only activates when the vehicle is traveling forward at the speed of approximately 5 mph (8 km/h) or more.
Headlight beam leveler
LED headlights produce more light than conventional halogen headlights. When the vehicle is carrying a heavy load and the headlight beams are angled upwards, the driver of an oncoming vehicle may experience glare. To prevent this, the automatic headlight beam leveler adjusts the headlights to the optimum height automatically depending on the load the vehicle is carrying.
CAUTION
In certain circumstances, the headlights may become misaligned, and the headlight beam leveler will not reset them to the proper angle. This may occur after transporting your vehicle on a flatbed truck, or if the vehicle is parked and restarted on different angles. In such cases, have the headlight alignment checked by a SUBARU dealer?
Fog light switch (if equipped)
- Headlight switch
- Fog light switch
For Canada models
- Headlight switch
- Fog light switch
- The front fog lights will turn on when the fog light switch is placed in the position while the headlights are in the following
conditions. - The headlight switch is in the position with the low beam mode selected.
- For models with the auto on/off headlights, while the headlight switch is in the “AUTO” position the low beam headlights turn on automatically. To turn off the front fog lights, perform the following.
- Turn the switch to (except for Canada models).
Indicator light
The indicator light located on the combination meter will illuminate when the front fog lights are on.
Turn signal lever
- Right turn
- Lane change right signal
- Lane change left signal
- Left turn If the lever does not return after cornering, return the lever to the neutral position by hand.
- To signal a lane change, push the turn signal lever up or down slightly and hold it during the lane change. The lever will return automatically to the neutral position when you release it.
One-touch lane changer
To flash the turn signal and turn the signal indicator light three times, push the turn signal lever up or down slightly and immediately release it.
NOTE
The operational/non-operational setting of the one-touch lane changer can be changed by a SUBARU dealer. Contact the nearest SUBARU dealer for details. The setting can also be changed by operating the center information display.
Wiper and washer
WARNING
In freezing weather, do not use the windshield washer until the windshield is sufficiently warmed by the defroster. Otherwise, the washer fluid can freeze on the windshield, blocking your view.
CAUTION
- Do not operate the washer continuously for more than 10 seconds, or when the washer fluid tank is empty. This may cause
overheating of the washer motor. Check the washer fluid level frequently, such as at fuel stops. - Do not operate the wipers when the windshield or rear window is dry. This may scratch the glass, damage the blade rubbers, and might cause the wiper motor to fail. Before operating the wiper on a dry windshield or rear window, always use the windshield washer.
- In freezing weather, be sure that the blade rubbers are not frozen to the windshield or rear window before switching on the wipers. Attempting to operate the wiper with the blades frozen to the window glass could cause not only the blade rubbers to be damaged but also might cause the wiper motor to fail. If the blade rubbers are frozen to the window glass, be sure to operate the defroster, windshield wiper deicer (if equipped) or rear window defogger before turning on the wiper.
- If the wipers stop during operation because of ice or some other obstruction on the window, this might cause the wiper motor to fail even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turn the ignition switch to the “LOCK”/“OFF” position and clean the window glass to allow proper wiper operation.
- Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent.
- Do not clean the blade rubbers with gasoline or a solvent, such as paint thinner or benzene. This will cause deterioration of the blade rubbers.
NOTE
- The windshield wiper motor is protected against overloads by a circuit breaker. If the motor operates continuously under an unusually heavy load, the circuit breaker may trip to stop the motor temporarily. If this happens, park your vehicle in a safe place, turn off the wiper switch, and wait for approximately 10 minutes. The circuit breaker will reset itself, and the wipers will again operate normally.
- Clean your blade rubbers and window glass periodically with a washer solution to prevent streaking, and to remove accumulations of road salt or road film. Operate the windshield washer for at least 1 second so that the washer solution will be sprinkled all over the windshield or rear window.
- Grease, wax, insects, or other material on the windshield or the wiper blade results in jerky wiper operation and streaking on the glass. If you cannot remove the streaks after operating the windshield washer or if the wiper operation is jerky, clean the outer surface of the windshield and rear window using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. Do not, however, use detergent to clean the blade rubbers.
- Use only a sponge or soft cloth (and no neutral detergent or mild abrasive cleaner) when you clean the blade rubbers. If you wipe the rubber of the blade strongly, the black coating component will peel off, which will cause the wiper to judder. Also, after wiping it off, check that the rubber has not come loose. After cleaning the window glass and wiper blade rubbers, be sure to rinse them with clean water. Rinse the window until the water does not form beads on the glass. This indicates that the glass is clean. blade results in jerky wiper operation and streaking on the glass. If you cannot remove the streaks after operating the windshield washer or if the wiper operation is jerky, clean the outer surface of the windshield and rear window using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. Do not, however, use detergent to clean the blade rubbers.. If you cannot eliminate the streaking even after following this procedure, replace the blade rubbers with new ones.
Windshield wiper and washer switches
The wiper operates only when the ignition switch is in the “ON” or “ACC” position.
Windshield wipers
- Mist (for a single wipe)
- Off
- Intermittent
- Low speed
- High speed
To turn the wipers on, push the wiper control lever down. To turn the wipers off, return the lever to the position. For a single wipe of the wipers, push the lever up. The wipers operate until you release the lever.
Wiper intermittent time control
When the wiper switch is in the position, turn the dial to adjust the operating interval of the wiper. The operating interval can be adjusted in several steps from the shortest interval to the longest.
Windshield washer
To wash the windshield, pull the wiper control lever toward you. The washer fluid sprays until you release the lever. The wipers operate while you pull the lever.
Windshield washer fluid warning light
NOTE
The windshield washer fluid warning light illuminates when the washer fluid level in the tank has dropped to the lower limit. If the warning light illuminates, refill the tank with fluid.
Rear window wiper and washer switch
- Washer operation (accompanied by wiper operation)
- continuous operation
- Intermittent operation
- Off
Rear wiper
Washer operation (accompanied by wiper operation)With the switch turned to the position, the rear wiper will operate intermittently at intervals corresponding to the vehicle speed. In this position, when you move the select lever to the “R” position, the rear wiper will switch to continuous operation. When you move the select lever from the “R” (reverse) position to another position, the rear wiper will return to intermittent operation.
Reverse gear interlocked rear wiper:
Even if the rear wiper switch is in the off position, if the front windshield wiper is operating continuously, the rear wiper will operate intermittently when you move the select lever to the “R” (reverse) position. The factory setting (default setting) of the reverse gear interlocked rear wiper is as follows.
- U.S.-spec. models: Non-operational
- Other models: Operational This setting can be changed by a SUBARU dealer. Consult your SUBARU dealer for details.
CAUTION
Do not attach anything that disturbs the rear wiper operation on the rear gate. Doing so may damage the rear wiper when it operates.
Washer
To wash the rear window while the rear wiper is operating, turn the knob switch upward to the position. The washer fluid sprays until you release the knob. To wash the rear window when the rear wiper is not in use, turn the knob switch downward to the position. The washer fluid sprays and the wiper operate until you release the knob. The rearview camera washer also operates while the rear window washer is operating.
Windshield washer fluid warning light
NOTE
The windshield washer fluid warning light appears when the washer fluid level in the tank has dropped to the lower limit. If the warning light appears, refill the tank with fluid.
Defogger and Deicer
- Rear window defogger
- Outside mirror defogger (if equipped)
- Windshield wiper deicer (if equipped)
The defogger and deicer system is activated only when the ignition switch is in the “ON” position.
Rear window and outside mirror (if equipped) defogger button (dual 7.0-inch display models)
Rear window and outside mirror defogger button (11.6-inch display models) To activate the defogger and deicer system, press the rear window and outside mirror defogger buttons. The rear window defogger, outside mirror defogger, and windshield wiper deicer are activated simultaneously. The indicator light on the button illuminates while the defogger and deicer system is activated. To turn them off, press the button again. They also turn off when the ignition switch is turned to the “ACC” or “LOCK”/“OFF” position. The defogger and deicer system will automatically shut off after approximately 15 minutes. If the rear window and outside mirrors have been cleared and the windshield wiper blade rubbers have been deiced completely before that time, press the button to turn them off. If defrosting, defogging or deicing is not complete, you have to press the button to turn them on again. It is possible to set the defogger and deicer system for the continuous operation mode by operating the center information display.
CAUTION
- To prevent the battery from being discharged, do not operate the defogger and deicer system continuously for any longer than necessary.
- Do not use sharp instruments or window cleaners containing abrasives to clean the inner surface of the rear window. They may damage the conductors printed on the window.
NOTE
- Turn on the defogger and deicer system if the wipers are frozen to the windshield.
- If the windshield is covered with snow, remove the snow so that the windshield wiper deicer works effectively.
- While the defogger and deicer system is in continuous operation mode:
- If the vehicle speed remains at 9 mph (15 km/h) or lower for 15 minutes, the windshield wiper deicer system automatically stops operating. However, the rear window defogger system and outside mirror defogger system maintain continuous operation in this condition.
- If the vehicle battery voltage drops below the permissible level, continuous operation of the defogger system and deicer system is canceled and the system stops operating.
- The vehicle is equipped with a radio antenna on the upper part of the rear window. Therefore it is not possible to clear fog and frost on the upper part of the rear window.
FAQ
What is the Subaru Legacy 2023 Touring XT and what features does it offer?
The Subaru Legacy 2023 Touring XT is a midsize sedan that offers a range of features for a comfortable and safe driving experience. The Touring XT trim level includes additional features such as adaptive LED headlights, a heated steering wheel, and a windshield wiper de-icer.
What is the adaptive LED headlight system in the Subaru Legacy 2023?
The adaptive LED headlight system in the Subaru Legacy 2023 automatically adjusts the direction and intensity of the headlights based on the steering angle and vehicle speed. This feature provides better visibility and safety when driving at night.
How do I activate the windshield wiper de-icer in the Subaru Legacy 2023?
To activate the windshield wiper de-icer in the Subaru Legacy 2023, simply press the windshield wiper de-icer button on the dashboard. This will activate the heating element in the windshield wiper blades and help melt any ice or snow that may be obstructing the view.
What is the benefit of a heated steering wheel in the Subaru Legacy 2023?
The benefit of a heated steering wheel in the Subaru Legacy 2023 is that it provides a warm and comfortable grip on the steering wheel during cold weather, making it more comfortable to drive.
How do I adjust the steering wheel in the Subaru Legacy 2023?
To adjust the steering wheel in the Subaru Legacy 2023, pull the lever located underneath the steering column and adjust the steering wheel up, down, or in and out to the desired position. Then, push the lever back to lock the steering wheel in place.
How do I activate the automatic headlights in the Subaru Legacy 2023?
To activate the automatic headlights in the Subaru Legacy 2023, simply turn the headlight switch to the “Auto” position. This will activate the headlights when the vehicle detects low light conditions.
How do I adjust the sensitivity of the automatic headlights in the Subaru Legacy 2023?
To adjust the sensitivity of the automatic headlights in the Subaru Legacy 2023, press and hold the headlight switch in the “Auto” position until the headlights flash. Then, release the switch and adjust the sensitivity using the “+” and “-” buttons.
How often should I replace the windshield wiper blades on my Subaru Legacy 2023?
It is recommended to replace the windshield wiper blades on your Subaru Legacy 2023 every six to twelve months, or as soon as you notice any signs of wear or reduced performance.
How do I replace the windshield wiper blades on my Subaru Legacy 2023?
To replace the windshield wiper blades on your Subaru Legacy 2023, lift the wiper arm away from the windshield and press the release tab on the wiper blade to remove it. Then, attach the new wiper blade by sliding it onto the wiper arm until it clicks into place.
How do I check the steering fluid level in my Subaru Legacy 2023?
To check the steering fluid level in your Subaru Legacy 2023, locate the power steering fluid reservoir under the hood and remove the cap. The fluid level should be between the “Min” and “Max” marks on the reservoir.
How often should I change the steering fluid in my Subaru Legacy 2023?
It is recommended to change the steering fluid in your Subaru Legacy 2023 every 30,000 to 60,000 miles or every three to four years, depending on driving conditions.
Useful Link
View Full User Guide: Subaru Legacy 2023 Touring XT User Guide
Download Manuals: https://www.subaru.com/owners/vehicle-resources/manuals.html
2024 Subaru Legacy Specs, Price, Features, Mileage (Brochure)