2023 FORD Transit Wipers Guide
Introduction
Introducing the 2023 Ford Transit’s Enhanced Wiper System: A Clearer View on Every Trip
With its cutting-edge wiper system, the 2023 Ford Transit combines innovation and utility. These cutting-edge wipers have been painstakingly built to overcome even the most difficult weather conditions, ensuring a clear and unimpeded vision of the road ahead. Designed to provide you an unmatched driving experience.
WIPERS
WIPER PRECAUTIONS
- Fully defrost the windshield before you switch the windshield wipers on.
- Make sure that you switch the windshield wipers off before entering a car wash.
- If streaks or smears appear on the windshield, clean the windshield and the wiper blades. See Checking the Wiper Blades (page 112). If that does not resolve the issue, install new wiper blades. See Replacing the Front Wiper Blades (page 112).
- Do not operate the wipers on a dry windshield. This may scratch the glass or damage the wiper blades. Always use the windshield washers before wiping a dry windshield.
- When your vehicle speed increases, the interval between intermittent wipes may decrease.
SWITCHING WINDSHIELD WIPERS ON AND OFF
- A Single wipe.
- B Intermittent wipe.
- C Normal wipe.
- D High-speed wipe.
AUTOWIPERS
WHAT ARE AUTOWIPERS
Autowipers turns on and controls the speed and frequency of the windshield wipers.
AUTOWIPERS SETTINGS
- Using the instrument cluster display controls on the steering wheel, select Settings.
- Select Vehicle Settings.
- Select Wipers.
- Switch Rain Sensing on or off.
ADJUSTING THE SENSITIVITY OF THE RAIN SENSOR
- A High sensitivity.
- B Autowipers on.
- C Low sensitivity.
Use the rotary control to adjust the sensitivity of the autowipers.
Note: Keep the outside of the windshield clean. The rain sensor is very sensitive and the wipers may operate if dirt, mist or insects hit the windshield.
CHECKING THE WIPER BLADES
Run the tip of your fingers over the edge of the blade to check for roughness.
REPLACING THE FRONT WIPER BLADES
- Lift the wiper arm. Press the wiper blade locking button.
Note: Do not hold the wiper blade when lifting the wiper arm. - Remove the wiper blade
Note: Make sure that the wiper arm does not spring back against the glass when the wiper blade is not attached. - To install, reverse the removal procedure.
Note: Make sure that the wiper blade locks into place.
WASHERS
WASHER PRECAUTIONS
Do not operate the washers when the washer reservoir is empty. This could cause the washer pump to overheat.
USING THE WINDSHIELD WASHER
Pull the lever toward you to operate the windshield washer.
Note: A courtesy wipe occurs a short time after the wipers stop to clear any remaining washer fluid when switched on. See Switching the Courtesy Wipe On and Off
SWITCHING THE COURTESY WIPE ON AND OFF
- Using the instrument cluster display controls on the steering wheel, select Settings.
- Select Vehicle Settings.
- Select Wipers.
- Switch Courtesy Wipe on or off.
ADDING WASHER FLUID
- Remove the washer fluid reservoir cap.
- Add washer fluid that meets our specification. See Washer Fluid Specification (page 462).
- Install the washer fluid reservoir cap.
Note: The reservoir supplies the front and rear washer systems.
WIPERS AND WASHERS – TROUBLESHOOTING
WIPERS AND WASHERS –WARNING LAMPS
Illuminates when the windshield washer fluid is low.
WIPERS AND WASHERS –FREQUENTLY ASKED QUESTIONS
- Why are there streaks and smears on the windshield?
- The wiper blades could be dirty, worn or damaged.
- Check the wiper blades. See Checking the Wiper Blades.
- If the wiper blades are dirty, clean them with washer fluid or water applied with a soft sponge or cloth.
- If the wiper blades are worn or damaged, install new ones.
- See Replacing the Front Wiper Blades.
FAQs
Use the wiper stalk on the right side of the steering wheel to operate the wipers. For a single wipe, push the stalk down; for intermittent settings, rotate the stalk; and for continuous cleaning, push the stalk up.
A variety of wiper speed options, such as intermittent, low, high, and occasionally an automatic setting, are commonly available on the 2023 Ford Transit.
If your Transit has automatic wipers, you can usually change the sensitivity through the settings menu in the car.
Typically, there is a separate button or switch on the wiper stalk. Look for a representation of the rear windshield wiper in a symbol.
Yes, you may remove the wiper arms away from the windshield in many cars to clean or maintain them. Take care to prevent them from returning to the windshield.
Lift the wiper arm away from the windshield to access the wiper blade assembly, press the release tab, and then slide the old blade off. Once it clicks, move the new blade into position.
The size of the wiper blades will depend on the Transit’s particular model and trim. For the correct size, consult your owner’s manual or get in touch with a Ford dealershi
Some 2023 Ford Transit models could be fitted with rain-sensing wipers, which turn on when they spot condensation on the windshield.
Most cars do not come standard with heated wiper blades, but some pricier trim levels or extras might.
Squeaky wipers may be the result of worn or damaged wiper blades, a filthy windshield, or the necessity for wiper blade rubber cleaning.
It is advised to use windshield washer fluid designed for colder climates because it won’t freeze in the reservoir during the winter.
Wiper blades should typically be changed every 6 to 12 months or if you detect streaking, skipping, or decreased visibility.
Inspect the wiper arm for damage or bending. If not, the wiper blade may need to be replaced since it is worn out.
Before turning off the car, it’s a good idea to turn off the wipers to avoid them sticking to the windshield and maybe stressing the wiper motor.
It is not advised to use the wipers to clear away ice or thick snow as this could harm the blades and put undue strain on the wiper motor. Clear the windshield first with an ice scraper and brush.
Useful Link :
View Full PDF:2023 FORD Transit Owner’s Manual| Auto User Guide
Download Manual: Ford Vehicle Owner Manuals | Ford