2022 Nissan ARMADA Warning, indicator lights, and display Setup 

The 2022 Nissan Armada’s warning, indicator, and display lights work together as an important communication hub between the car and the driver. They are part of a complex system that gives the driver up-to-date and important information about the car’s status and operation. These displays and lights do a lot of different things. For example, Nissan armada warning lights
can let the driver know about possible problems like engine problems, low tyre pressure, or problems with the brake system. Other features, like the tire pressure monitoring system (TPMS), blind-spot warning indicators, and the ability to change the vehicle settings through the easy-to-use infotainment display, make the car safer and more convenient. Together, they not only keep the driver informed about the state of the vehicle, but they also make driving more enjoyable by promoting safety, efficiency, and customization. All of these features are seamlessly built into the 2022 Nissan Armada’s driving environment.

2023 Nissan Armada Specs, Price, Features and Mileage (Brochure)

WARNING LIGHTS, INDICATOR LIGHTS, AND AUDIBLE REMINDERS

Nissan Armada Dashboard Symbols And Meanings

• Automatic Transmission (AT) oil temperature warning light
• Automatic Transmission (AT) park warning light
• Brake warning light
• Charge warning light
• Engine oil pressure warning light
• Master warning light
• Seat belt warning light
• Security indicator light Supplemental air bag warning light
• Anti-lock Braking System (ABS) warning light
• Automatic Emergency Braking (AEB) system warning light
• Automatic transmission check warn-ing light
• Check the suspension indicator light
• Front passenger airbag status light
• Four-Wheel Drive (4WD) warning light (4WD models)
• Low tire pressure warning light
• Malfunction Indicator Light (MIL)
• Master warning light
• Rear Automatic Braking (RAB) system warning light
• Vehicle Dynamic Control (VDC) off indicator light
• Vehicle Dynamic Control (VDC) warning light
• Exterior light indicator
• Front fog light indicator light (if so equipped)
• High beam assist indicator light
• High beam indicator light
• TOW mode indicator light
• Turn signal/hazard indicator lights

CHECKING LIGHTS

With all doors closed, apply the parking brake, fasten the seat belts, and place the ignition switch in the ON position without starting the engine. The following lights (if so equipped) will come on:

If any light does not come on or operates in a way other than described, it may indicate a burned-out bulb and/or a system malfunction. It is recommended you have the system checked by a NISSAN dealer.
Some indicators and warnings are also displayed on the vehicle information display between the speedometer and tachometer.

WARNING/INDICATOR LIGHTS (red)

Nissan Armada warning lights 

Automatic Transmission (AT)
oil temperature warning light
This light illuminates when the Automatic Transmission (AT) oil temperature is too high. If the light illuminates while driving, reduce the vehicle speed as soon as safely possible until the light turns off.

CAUTION
Continued vehicle operation, when the AT oil temperature warning light is on, may damage the AT.

Automatic Transmission (AT)
park warning light (4WD models)
This light indicates that the Automatic Transmission (AT) parking function is not engaged. If the transfer control is not secured in any driving position while the AT shift lever is in the “P” (Park) position, the transmission will disengage and the wheels will not lock.
If the AT park warning light illuminates with the shift lever in the P (Park) position, shift the Four-Wheel Drive (4WD) shift switch to the AUTO, 4H or 4L position again with the shift lever in the N (Neutral) position.

Brake warning light
This light functions for both the parking brake and the foot brake systems.
Parking brake indicator:
When the ignition switch is in the ON position, the light comes on when the parking brake is applied.

Low brake fluid warning light:
When the ignition switch is in the ON position, the light warns of a low brake fluid level. If the light comes on while the engine is running with the parking brake not applied, stop the

vehicle and perform the following:

1. Check the brake fluid level. If brake fluid is low, add fluid and have the system checked. It is recommended you have this service performed by a NISSAN dealer.
2. If the brake fluid level is correct, have the warning system checked. It is recommended you have this service performed by a NISSAN dealer.

Low hydraulic pressure warning indicator:
If the brake warning light illuminates when the engine is running, or while driving with the parking brake is released, check the brake fluid level. If the brake fluid level is sufficient, it may indicate low hydraulic pressure in the brake booster. It is recommended that you have the brake system checked by a NISSAN dealer promptly.

Anti-lock Braking System (ABS) warning indicator:
When the parking brake is released and the brake fluid level is sufficient, if both the brake warning light and the Anti-lock Braking System (ABS) warning light illuminate, it may indicate the ABS is not functioning properly. Have the brake system checked, and if necessary repaired. It is recommended you visit a NISSAN dealer for this service.

WARNING

• Your brake system may not be working properly if the warning light is on. Driving could be dangerous. If you judge it to be safe, drive carefully to the nearest service station for repairs. Otherwise, have your vehicle towed because driving it could be dangerous.
• Pressing the brake pedal with the engine stopped and/or low brake fluid level may increase your stopping distance and braking will require greater pedal effort as well as pedal travel.
•  If the brake fluid level is below the minimum or MIN mark on the brake fluid reservoir, do not drive until the brake system has been checked. It is recommended you visit a NISSAN dealer for this service.

Charge warning light
When the ignition switch is in the ON position, the charge warning light illuminates and then turns off.
If the light comes on while the engine is running, it may indicate the charging system is not functioning properly. Turn the engine off and check the alternator belt. If the belt is loose, broken, or missing or if the light remains on, have your vehicle serviced immediately. It is recommended

CAUTION
Do not continue driving if the alternator belt is loose, broken or missing.

Engine oil pressure warning
This light warns of low engine oil pressure. If the light flickers or comes on during normal driving, pull off the road in a safe area, stop the engine immediately and call a NISSAN dealer or other authorized repair shop.
The engine oil pressure warning light is not designed to indicate a low oil level.

CAUTION
Running the engine with the engine oil pressure warning light on could cause serious damage to the engine almost immediately. Such damage is not covered by warranty. Turn off the engine as soon as it is safe to do so.

Master warning light
When the ignition switch is in the ON position, the master warning light illuminates when a warning message appears in the vehicle information display.

Seat belt warning light and chime
For driver and front passenger:
The light and chime remind you to fasten the driver and front passenger seat belts.
The light illuminates whenever the ignition switch is pushed to the ON position and will remain illuminated until the front seat belts are fastened.
When the vehicle speed exceeds approximately 10 MPH (15 km/h), the light will blink unless the front seat belts are securely fastened.
When the ignition switch is pushed to the ON position, the chime will sound for approximately 6 seconds unless the driver’s seat belt is securely fastened.
When the vehicle speed exceeds approximately 10 MPH (15 km/h), the chime will sound unless the front seat belts are securely fastened. The chime will continue to sound for approximately 95 seconds until the front seat belts are fastened.

For rear passengers:
The seat belt warning light for the rear passengers will illuminate whenever the ignition switch is pushed to the ON position and will remain illuminated until the rear passenger’s seat belts are fastened.
For approximately 65 seconds after the ignition switch is in the ON position, the system does not activate the warning light for the rear passengers.
If a rear passenger seat belt is fastened and then unfastened at a vehicle speed less than approximately 10 MPH (15 km/h), the warning light will illuminate. When the vehicle speed exceeds approximately 10 MPH (15 km/h), the warning light will blink and the chime will sound.
The warning will turn off when a rear passenger seat belt is fastened or automatically turned off approximately 65 seconds after the seat belt is unfastened.

Security indicator light
The light blinks when the ignition switch is in the ACC, OFF and LOCK positions. This function indicates the security system equipped on the vehicle is operational.
If the security system is malfunctioning, this light will remain on while the ignition switch is in the ON position. 

Supplemental air bag warning light
After placing the ignition switch in the ON position, the supplemental air bag warning light will illuminate. The supplemental airbag warning light will turn off after about 7 seconds if the airbag and/or pretensioner systems are operational.
If any of the following conditions occur, the airbag and/or pre-tensioner systems need servicing.

• The supplemental air bag warning light remains on after approximately 7 seconds.
• The supplemental air bag warning light flashes intermittently.
• The supplemental air bag warning light does not come on at all. It is recommended you visit a NISSAN dealer for these services.
  Unless checked and repaired, the supplemental restraint system (air bag system) and/or the pretensioners may not function properly.

WARNING
If the supplemental air bag warning light is on, it could mean that the front airbag, side air bag, curtain air bag systems and/or pre-tensioner systems will not operate in an accident. To help avoid injury to yourself or others, have your vehicle checked. It is recommended you visit a NISSAN dealer for this service.

WARNING/INDICATOR LIGHTS (yellow)

Anti-lock Braking System (ABS) warning light
When the ignition switch is in the ON position, the Anti-lock Braking System (ABS) warning light illuminates and then turns off. This indicates the ABS is operational.
If the ABS warning light illuminates while the engine is running, or while driving, it may indicate the ABS is not functioning properly. Has the system checked? It is recommended you visit a NISSAN dealer for this service.
If an ABS malfunction occurs, the anti-lock function is turned off. The brake system then operates normally but without anti-lock assistance.

Automatic Emergency Braking (AEB) system warning light
This light comes on when the ignition switch is placed in the ON position. It turns off after the engine is started.
This light illuminates when the Automatic Emergency Braking (AEB) system is set to OFF in the vehicle information display.
If the light illuminates when the AEB system is ON, it may indicate that the system is unavailable. 
When the ignition switch is placed in the ON position, the light comes on for 2 seconds. If the light comes on at any other time, it may indicate the transmission is not functioning properly. It is recommended you visit a NISSAN dealer to check and repair the transmission.

Check suspension indicator
When the ignition switch is placed in the ON position, the light comes on for 2 seconds.

Front passenger airbag status light
The front passenger air bag status light ( ) located on the instrument panel will be lit and the passenger front airbag will be OFF depending on how the front passenger seat is being used.

Four-Wheel Drive (4WD) warning light (4WD models)
The warning light comes on when the ignition switch is placed in the ON position. It turns off soon after the engine is started.
If the 4WD system malfunctions, or the diameter of the front and the rear wheels are different, the warning light will either remain illuminated or blink. 

CAUTION

• If the warning light comes on while driving there may be a malfunction in the 4WD system. Reduce the vehicle speed and have your vehicle checked as soon as possible. It is recommended you visit a NISSAN dealer for this service.
• If the 4WD warning light turns on when driving on dry or hard-surfaced roads:
  •  in the 4H(I) position, shift them4WD shift switch to AUTO
  • in the 4L(O) position, stop the vehicle and shift the transmission shift lever to the N (Neutral) position and shift the 4WD shift switch to AUTO
• If the warning light is still on after the above operations, have your vehicle checked as soon as possible. It is recommended you visit a NISSAN dealer for this service.

Low tire pressure warning
Your vehicle is equipped with a Tire Pressure Monitoring System (TPMS) that monitors the tire pressure of all tires except the spare.
The low tire pressure warning light warns of low tire pressure or indicates that the TPMS is not functioning properly.
After the ignition switch is placed in the ON position, this light illuminates for about 1 second and turns off.
Low tire pressure warning:
If the vehicle is being driven with low tire pressure, the warning light will illuminate. The “Tire Pressure Low Add Air” warning also appears in the vehicle information display. If you select the tire pressure information in the vehicle information display, the Low-Pressure information will be displayed. The tire pressure for each tire will also be displayed.
When the low tire pressure warning light illuminates, you should stop and adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label. The low tire pressure warning light does not automatically turn off when the tire pressure is adjusted. After the tire is inflated to the recommended pressure, the vehicle must be driven at speeds above 16 MPH (25 km/h) to activate the TPMS and turn off the low tire pressure warning light. Use a tire pressure gauge to check the tire pressure.
The “Tire Pressure Low Add Air” warning appears each time the ignition switch is placed in the ON position as long as the low tire pressure warning light remains illuminated.

TPMS malfunction:
If the TPMS is not functioning properly, the low tire pressure warning light will flash for approximately 1 minute when the ignition switch is placed in the ON position. The light will remain on after 1 minute. Has the system been checked? It is recommended you visit a NISSAN dealer for this service. The “Tire Pressure Low -Add Air” warning does not appear if the low tire pressure warning light illuminates to indicate a TPMS malfunction.

WARNING

• if the light does not illuminate with the ignition switch placed in the ON position, have the vehicle checked as soon as possible. It is recommended you visit a NISSAN dealer for this service.
• If the light illuminates or Low-Pressure information is displayed on the monitor screen while driving, avoid sudden steering manoeuvres or abrupt braking, reduce vehicle speed, pull off the road to a safe location, and stop the vehicle as soon as possible. Driving with under-inflated tires may permanently damage the tires and increase the likelihood of tire failure. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If the light still illuminates while driving after adjusting the tire pressure, a tire may be flat or the TPMS may be malfunctioning. If you have a flat tire, replace it with a spare tire as soon as possible. If no tire is flat and all tires are properly inflated, it is recommended you consult a NISSAN dealer.
• Since the spare tire is not equipped with the TPMS, when a spare tire is mounted or a wheel is replaced, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Have your tires replaced and/or the TPMS system reset as soon as possible. It is recommended you visit a NISSAN dealer for these services.
• Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.

CAUTION

• The TPMS is not a substitute for the regular tire pressure check. Be sure to check the tire pressure regularly.
• If the vehicle is being driven at speeds of less than 16 MPH (25 km/h), the TPMS may not operate correctly.
• Be sure to install the specified size of tires to the four wheels correctly.

Malfunction Indicator Light
If the malfunction indicator light comes on steady or blinks while the engine is running, it may indicate a potential emission control malfunction.
The malfunction indicator light may also come on steady if the fuel-filler cap is loose or missing, or if the vehicle runs out of fuel. Check to make sure the fuel-filler cap is installed and closed tightly, and that the vehicle has at least 3 US gallons (14 liters) of fuel in the fuel tank.
After a few driving trips, the light should turn off if no other potential emission control system malfunction exists.
If this indicator light remains on for 20 seconds and then blinks for 10 seconds when the engine is not running, it indicates that the vehicle is not ready for an emission control system inspection/maintenance test.

Operation:
The malfunction indicator light will come on in one of two ways:

• Malfunction indicator light on steady
  • An emission control system malfunction has been detected. Check the fuel-filler cap if the Loose Fuel Cap warning appears in the vehicle information display. If the fuel-filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The light should turn off after a few driving trips. If the light does not turn off after a few driving trips, have the vehicle inspected. It is recommended you visit a NISSAN dealer for this service. You do not need to have your vehicle towed to the dealer.
• Malfunction indicator light blinking  An engine misfire has been detected which may damage the emission control system.
  To reduce or avoid emission control system damage:
  1. Do not drive at speeds above 45 MPH (72 km/h).
  2. Avoid hard acceleration or deceleration.
  3.  Avoid steep uphill grades.
  4.  If possible, reduce the amount of cargo being hauled or towed.

The malfunction indicator light may stop blinking and remain on.
Has the vehicle been inspected? It is recommended you visit a NISSAN dealer for this service. You do not need to have your vehicle towed to the dealer.

CAUTION
Continued vehicle operation without having the emission control system checked and repaired as necessary could lead to poor drivability, reduced fuel economy, and possible damage to the emission control system.

Master warning light
When the ignition switch is in the ON position, the master warning light illuminates when a warning message appears in the vehicle information display.
Rear Automatic Braking (RAB)

system warning light
This light comes on when the ignition switch is placed in the ON position. It turns off after the engine is started.
This light illuminates when the RAB system is turned off in the vehicle information display.
If the light illuminates when the RAB system is on, it may indicate that the system is unavailable.

Vehicle Dynamic Control (VDC) off indicator light
When the ignition switch is in the ON position, the Vehicle Dynamic Control (VDC) off indicator light illuminates and then turns off.
The light comes on when the VDC off switch is pushed to OFF. This indicates that the VDC system is not operating.
When the 4L position is selected with the Four-Wheel Drive (4WD) shift switch, the VDC system is disabled and the VDC off indicator light illuminates. (4WD models)

Vehicle Dynamic Control (VDC) warning light
When the ignition switch is in the ON position, the Vehicle Dynamic Control (VDC) warning light illuminates and then turns off.
The light will blink when the VDC system or the traction control system is operating, thus alerting the driver that the vehicle is nearing its traction limits. The road surface may be slippery.
When the VDC warning light illuminates when the VDC system is turned on, this light alerts the driver to the fact that the VDC system’s fail-safe mode is operating, for example, the VDC or hill start assist system may not be functioning properly. Have the system checked. It is recommended you visit a NISSAN dealer for this service. If a malfunction occurs in the system, the VDC system function will be cancelled but the vehicle is still driveable.

WARNING/INDICATOR LIGHTS (other)

Exterior light indicator
This indicator illuminates when the headlight switch is turned to the AUTO or position and the front parking lights, instrument panel lights, rear combination lights, license plate lights or headlights are on. The indicator turns off when these lights are turned off.

Front fog light indicator light (if so equipped)
The front fog light indicator light illuminates when the front fog lights are on.

High beam assist indicator
The high beam assist indicator light illuminates when the high beam assist system is turned on and it is operational

High beam indicator light
This light comes on when the headlight’s high beam is on and goes out when the low beam is selected.

TOW mode indicator light
This light will illuminate when the TOW MODE is selected while the engine is running.

Turn signal/hazard indicator lights
The light flashes when the turn signal switch lever or hazard switch is turned on.

AUDIBLE REMINDERS

Door lock warning chime
When the chime sounds, be sure to check both the vehicle and the Intelligent Key.

Light reminder chime
A chime will sound when the driver-side door is opened with the headlight switch in the or position and the ignition switch in the ACC, OFF or LOCK position.
Turn the headlight switch to the OFF (if so equipped) or the AUTO position when you leave the vehicle.

Parking brake reminder chime
The chime will sound if the vehicle is driven at more than 4 MPH (7 km/h) with the parking brake applied. Stop the vehicle and release the parking brake.

Brake pad wear warning
The disc brake pads have audible wear warnings. When a brake pad requires replacement, it will make a high-pitched scraping sound when the vehicle is in motion. This scraping sound will first occur only when the brake pedal is depressed. After more wear of the brake pad, the sound will always be heard even if the brake pedal is not depressed. Have the brakes checked as soon as possible if the warning sound is heard.

VEHICLE INFORMATION DISPLAY

The vehicle information display is located between the tachometer and the speedometer, and it displays the warnings and information. The following items are also displayed if the vehicle is equipped with them:

• Odometer/twin trip ram promaster odometer 
  
  • “Odometer/twin trip odometer”
• Automatic Transmission (AT)
  • “Warning lights, indicator lights, and audible reminders”
  • “Driving the vehicle”
• Four-wheel drive (4WD)
  •  “NISSAN all-mode 4WD®”
• Intelligent Back-up Intervention (I-BI)
  •  “Intelligent Back-up Intervention (I- BI)”
• Intelligent Cruise Control (ICC)
  • “Intelligent Cruise Control (ICC)”
• Intelligent Key system
  •  “Intelligent Key system”.
  •  “Push-button ignition switch”.
•  Automatic Emergency Braking (AEB) with pedestrian detection
  •  “Automatic Emergency Braking
    (AEB) with pedestrian detection system”.
• Intelligent Forward Collision Warning (I-FCW)
  • “Intelligent Forward Collision Warning (I-FCW)”.
• Lane Departure Warning (LDW)
  •  “Lane Departure Warning (LDW)”.
• Intelligent Lane Intervention (I-LI)
  • “Intelligent Lane Intervention (I-LI)”.
• Intelligent Blind Spot Intervention (IBSI)
  • “Intelligent Blind Spot Intervention (I-BSI)”.
• Blind Spot Warning (BSW)
  •  “Blind Spot Warning (BSW)”.
• Rear Automatic Braking (RAB)
  • “Rear Automatic Braking (RAB)”.
•  Intelligent Driver Alertness (I-DA)
  • “Intelligent Driver Alertness (I-DA)”.
• Traffic Sign Recognition (TSR)
  •  “Traffic Sign Recognition (TSR)”.
• Rear Cross Traffic Alert (RCTA)
  • “Rear Cross Traffic Alert (RCTA)” .

HOW TO USE THE VEHICLE INFORMATION DISPLAY

The vehicle information display can be changed using the buttons OK, and located on the steering wheel.

• OK – change or select an item in the vehicle information display
  navigate through the items in the vehicle information display
• go back to the previous menu
• change from one display screen to the next (i.e. trip, Fuel economy)

The OK , and buttons also control audio and control panel functions in some conditions. Most screens and menus offer instruction prompts of the steering switch buttons to indicate how to control the vehicle information display. The OK button changes the audio source and the buttons also control voice recognition manual mode. The OK button can be used to change the audio source when the audio screen is displayed. The buttons can be used when controlling voice recognition prompts manually. (See NissanConnect® Owner’s Manual.)

STARTUP DISPLAY

When the ignition switch is placed in the ON position, the vehicle information display may display the following screens if the vehicle is equipped with them:

• Home
•  Speed
• Drive Computer
• Fuel Economy
• Navigation
• Audio
• CRUISE
• Driving Aids
• TPMS
• Speed Limit Sign
  Warnings will only be displayed if there are any present. 

SETTINGS
The setting mode allows user to change the information displayed in the vehicle information display and some settings:

• Driver Assistance
• TPMS Setting
• Clock
• Vehicle settings
• Maintenance
• Customize Display
• Unit/Language
• Factory Reset
  Driver Assistance
  To change the status, and warnings or turn on or off any of the systems/warnings displayed in the “Driver Assistance” menu, use the buttons to select and change a menu item:
• Emergency Brake
• Lane
• Blind Spot
• Speed Limit Sign
• Cross Traffic Alert
• Driver Attention Alert
• Timer Alert
• Low Temp. Alert
  Emergency Brake:
• Front
  Allows user to turn the Automatic Emergency Braking (AEB) with pedestrian detection system and Intelligent Forward Collision Warning (I-FCW) system ON/OFF.
• Rear
  Allows user to turn the Rear Automatic Braking (RAB) system ON/OFF
  Lane:
• Warning(LDW)
  Allows user to turn the Lane Departure Warning (LDW) system ON/OFF. . Prevention(LDP)
  Allows user to turn the Intelligent Lane Intervention (I-LI) system ON/OFF.

Blind Spot:

• Warning(BSW)
  Allows user to turn the Blind Spot Warning (BSW) system ON/OFF.
• Intervention(BSI)
  Allows user to turn the Intelligent Blind Spot Intervention (I-BSI) system ON/OFF.

Speed Limit Sign (if so equipped):
Allows user to turn the Traffic Sign Recognition (TSR) ON/OFF.

Cross Traffic Alert (if so equipped):
Allows user to turn the Rear Cross Traffic Alert (RCTA) system ON/OFF. 

Driver Attention Alert:
Allows user to turn the Intelligent Driver Alertness (I-DA) on or off. 
Timer Alert:
Allows user to adjust the Timer Alert or reset.

• (Current Time)/(Set Time)
• Reset
  Low Temp. Alert:
  Allows user to turn the Low Temperature Alert function ON/OFF.
  TPMS Setting
  The following submenu appears.

Tire Pressure Unit:
The unit for tire pressure that is shown in the vehicle information display can be changed to:

• kPa
• psi
• bar
• kgf/cm2
  Use the buttons and the OK button to select and change the unit.
  If necessary, refer to the following table to convert between units.

Clock
Allows user to adjust the clock settings and time within the vehicle information display.

• Clock Mode (if so equipped)
• Clock Format
• Daylight Saving (if so equipped)
• Time Zone (if so equipped)
• Set Clock Manually
  The clock may also be set in the touchscreen display. For additional information, refer to the separate NissanConnect® Owner’s Manual.

Vehicle settings
The vehicle settings allow the user to change settings for the following menus.

• Lighting
• Locking
• Wipers (if so equipped)
• Driving Position (if so equipped)
• Rear Door Alert
• ACC Off Delay
  The vehicle settings can be changed using the buttons and the OK button.

Lighting:
The “Lighting” menu has the following

options:

• Auto Room Lamp
  The interior light can be set to be ON or OFF. Use the OK button to turn this feature ON or OFF.
• Auto Headlight
  The sensitivity of the Intelligent Auto Headlight (if so equipped) or auto light (if so equipped) can be adjusted. From the “Lighting” menu, select “Auto Headlight”. Use the buttons and the OK button to select the required sensitivity. The following options are available:
  • Turn on earliest
  • Turn on earlier
  • Turn on standard
  • Turn on later
• . Light Off Delay
  The duration of the automatic headlights can be changed from 0 to 180 seconds. Use the OK button to change the duration.

Locking:
The “Locking” menu has the following options:

• Ext. Door Switch (if so equipped)
  When this item is turned on, the request switch on the door is activated. Use the OK button to activate or deactivate this function.
• Selective Unlock (if so equipped)
  When this item is turned on, and the door handle request switch is pushed, only the corresponding door is un-locked. All the doors can be unlocked if the door handle request switch is pushed again within 1 minute. When this item is turned to off, all the doors will be unlocked when the door handle request switch is pushed once. Use the OK button to activate or deactivate this function.
• Auto Door Unlock
  The “Auto Door Unlock” feature allows user to customize the auto door unlock options. Use the OK button to change the mode.
  •  Shift to P
  •  IGN OFF
  •  OFF

Wipers (if so equipped):
The “Wipers” menu has the following options:

• Speed Dependent
  The “Speed Dependent” feature can be activated or deactivated. Use the OK button to turn this feature ON or OFF.

Driving Position (if so equipped):

• Exit Seat Slide
  This allows user to turn the entry/exit function ON or OFF. Use the OK button to turn this function ON or OFF.
• Exit Steering Up (if so equipped)
  This allows user to turn the entry/exit function ON or OFF. Use the OK button to turn this function ON or OFF

Rear Door Alert:
The “Rear Door Alert” feature allows user to customize the Rear Door Alert options. Use the OK button to change the mode.

• Horn & Alert
  When selected, the alert is displayed and the horn sounds.
• Alert Only
  When selected, only the alert is displayed.
• OFF
  When selected, no alert or horn will be active. 
  ACC Off Delay (if so equipped):
  This allows user to turn the ACC delay timer function ON or OFF.

Maintenance
The maintenance mode allows user to set alerts for the remainder of maintenance intervals. To change an item:

Select “Maintenance” using the tons and press the OK button.

• Oil and Filter
• Tire
• Other

Oil and Filter:

This indicator appears when the user set the distance comes for changing the engine oil and filter. You can set or reset the distance for checking or replacing these items. For scheduled maintenance items and intervals, refer to the “9. Maintenance and schedules” section.
Tire:
This indicator appears when the user set the distance comes for replacing tires. You can set or reset the distance for replacing tires.

WARNING
The tire replacement indicator is not a substitute for regular tire checks, including tire pressure checks. Many factors including tire inflation, alignment, driving habits and road conditions affect tire wear and when tires should be replaced. Setting the tire replacement indicator for a certain driving distance does not mean your tires will last that long. Use the tire replacement indicator as a guide only and always perform regular tire checks. Failure to perform regular tire checks, including tire pressure checks could result in tire failure. Serious vehicle damage could occur and may lead to a collision, which could result in serious personal injury or death.

Other:
This indicator appears when the user set a distance comes for checking or replacing maintenance items other than the engine oil, oil filter and tires. Other maintenance items can include such things as air filter or tire rotation. You can set or reset the distance for checking or replacing the items.

Customize Display
The display settings allows user to choose from the various meter selections.
The display settings can be changed using the buttons.

2023 Nissan Armada Specs, Price, Features and Mileage (Brochure)

Main Menu Selection:
Displays available screens that can be shown in the vehicle information display.
Route Guidance (if so equipped):
To change the setting, use the buttons and press the OK button.

• Alerts
  The “Alerts” allows user to turn the Route Guidance alerts on or off.

Welcome Effect:
The “Welcome Effect” displays the available welcome effect settings.

• gauges (if so equipped)
• Animation

Unit/Language
The units that are shown in the vehicle information display can be changed:

• Mileage/Fuel
• Temperature
• Language
  Use the buttons and the OK button to select and change the units of the vehicle information display.

Mileage/Fuel:
The unit for the mileage that is shown in the vehicle information display can be changed.

•  km, l/100km
• km, km/l
• miles, MPG(US) Use the buttons button to select and change the unit.
  Temperature:
  The temperature that is shown in the vehicle information display can be changed from:
• °C
• °F
  Use the OK button to toggle choices.

Language:
The language of the vehicle information display can be changed.
Use the buttons and the OK button to select and change the language of the vehicle information display.

Factory Reset
The settings in the vehicle information display can be reset back to the factory default. To reset the vehicle information display:

1. Select “Factory Reset” using the buttons and press the OK button.
2. Select “Yes” to return all settings back to default by pushing the OK button.

OPERATIONAL INDICATORS

The displayed images may differ depending on the model.

1. No Key Detected
   This warning appears when the Intelli-gent Key is left outside the vehicle with the ignition switch in the ON position. Make sure the Intelligent Key is inside the vehicle.
2. Key ID Incorrect
   This warning appears when the ignition switch is pushed from the OFF position and the Intelligent Key is not recognized by the system. You cannot start the engine with an unregistered key.
3. Key Battery Low
   This indicator appears when the Intelligent Key battery is running out of power.
   If this indicator appears, replace the battery with a new one. 
4. Key System Error: See Owner’s Manual
   This warning appears if there is a malfunction in the Intelligent Key system. If this warning appears while the engine is stopped, it may be impossible to start the engine.
   If this warning appears while the engine is running, you can drive the vehicle. However, in these cases, have the system checked. It is recommended you visit a NISSAN dealer for this service.
5. Key Registration Complete
   This indicator appears when a new Intelligent Key is registered to the vehicle.
6.  Push brake and start switch to drive
   This indicator appears when the shift lever is in the P (Park) position.
   This indicator also appears when the vehicle has been started using the Re-mote Engine Start function (if so equipped).
   This indicator means that the engine will start by pushing the ignition switch with the brake pedal depressed. You can start the engine from any position of the ignition switch.
7. Push Ignition to OFF
   After the Shift to Park warning illuminates, the warning will illuminate if the ignition switch is placed in the ACC position when the shift lever moves into the P (Park) position.
   To turn off the warning, place the ignition switch in the ON position and then in the LOCK position.
8.  Shift to Park
   This warning appears when the ignition switch is pushed to stop the engine with the shift lever in any position except the P (Park) position.
   If this warning appears, move the shift lever to the P (Park) position or push the ignition switch to the ON position.
   An inside warning chime will also sound.
9.  Engine start operation for Intelligent Key system indicator (if I-Key battery level is low)
   This indicator appears when the Intelligent Key battery is running out of power and when the Intelligent Key system and vehicle are not communicating normally.
   If this indicator appears, touch the ignition switch with the Intelligent Key while depressing the brake pedal. 
10.  Release Parking Brake
    This warning appears when the vehicle speed is above 4 MPH (7 km/h) and the parking brake is applied. Stop the vehicle and release the parking brake.
11. Low Fuel
    This warning appears when the fuel level in the tank is getting low. Refuel as soon as it is convenient, preferably before the fuel gauge reaches the 0 (Empty) position.
    There is a small reserve of fuel remaining in the tank when the fuel gauge reaches the 0 (Empty) position.
12. Low Washer Fluid This warning appears when the washer tank fluid is at a low level. Add washer fluid as necessary. 
13. Loose Fuel Cap
    This warning appears when the fuel-filler cap is not tightened correctly after the vehicle has been refueled. 
14. Tire Pressure Low Add Air
    This warning appears when the low tire pressure warning light in the meter illuminates and low tire pressure is detected. The warning appears each time the ignition switch is placed in the ON position as long as the low tire pressure warning light remains illuminated. If this warning appears, stop the vehicle and adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label. 
15. SNOW mode indicator
    This indicator appears when SNOW mode is selected by the SNOW mode switch.
16.  Four-Wheel Drive (4WD) shift
    indicator (4WD models)
    This indicator shows the Four-Wheel Drive (4WD) driving mode (AUTO, 4HI or 4LO) that is selected by the 4WD shift switch. 
17.  Door/liftgate open warning
    (ignition switch is in the ON position)
    This warning appears if any of the doors and/or the liftgate are open or not closed securely. The vehicle icon indicates which door or the liftgate is open on the display.
18. Power will turn off to save the
    battery
    This warning appears after a period of time if the ignition switch is in ACC or ON position.
19. Power turned off to save the
    battery
    This warning appears after the ignition switch is automatically turned OFF to save the battery.
20. Light reminder warning
    This warning appears when the driver-side door is opened the headlight switch is left ON and the ignition switch is placed in the OFF or LOCK position. Place the headlight switch in the OFF (if so equipped) or AUTO position. 
21. The vehicle ahead detection indicator
    This indicator shows the status of the following systems if the vehicle is equipped with them.
    • Automatic Emergency Braking (AEB) with the pedestrian detection system
    • Intelligent Forward Collision Warning
      (I-FCW)
      The figure and color of these indicators will change depending on the conditions of the above systems.
      22. LDW indicator
      This indicator shows the status of the following systems if the vehicle is equipped with them.
    • Lane Departure Warning (LDW)
    • Intelligent Lane Intervention (I-LI) For more details, see “Lane Departure Warning (LDW)” or “Intelligent Lane Intervention (I-LI)”
      The figure and color of these indicators will change depending on the conditions of the above systems.
22. BSW indicator
    This indicator shows the status of the following systems if the vehicle is equipped with them.
    • Blind Spot Warning (BSW)
    • Intelligent Blind Spot Intervention (I- BSI)
      For more details, see “Blind Spot Warning (BSW)”or “Intelligent Blind Spot Intervention (I-BSI)”
      The figure and color of these indicators will change depending on the conditions of the above systems.
23.  Malfunction
    This warning appears when one or more of the following systems (if so equipped) is not functioning properly:
    • Automatic Emergency Braking (AEB)
      with pedestrian detection system
    • Intelligent Forward Collision Warning (I-FCW)
    • Lane Departure Warning (LDW)
    • Intelligent Lane Intervention (I-LI)
    • Blind Spot Warning (BSW)
    • Intelligent Blind Spot Intervention (I- BSI)
    • Intelligent Back-up Intervention (I-BI) . Rear Cross Traffic Alert (RCTA)
      If one or more of these warnings appears, have the system checked. It is recommended you visit a NISSAN dealer for this service.
24. Wiper Mode Guidance
    This indicator shows the wiper and washer switch position.
    The selected position is illuminated in orange when the wiper switch position is changed.
25. Lights Mode Guidance
    This indicator shows the headlight switch position.
    The selected position is illuminated in orange when the headlight switch position is changed. (The display of the light position varies depending on the models.)
26. Intelligent Cruise Control (ICC)
    indicators
    These indicators show the Intelligent Cruise Control (ICC) system status. For additional information, refer to “Intelligent Cruise Control (ICC)” 
27. Stop the vehicle and Apply the parking brake (if so equipped)
    This warning may appear when the battery charge is low.
    Park the vehicle as soon as possible. It is recommended that you visit a NISSAN dealer.
28. Cruise indicator
    This indicator shows the conventional (fixed speed) cruise control mode status. The status is shown by the color.
29. Not Available: High Camera
    Temp (if so equipped)
    This message appears when the Lane Departure Warning (LDW)/Intelligent Lane Intervention (I-LI)/Intelligent Blind Spot Intervention (I-BSI) systems become un-available because a camera detects an interior temperature of more than 104°F (40°C).
    For additional information, refer to “Lane Departure Warning (LDW), “Intelligent Lane Intervention (I-LI)” or “Intelligent Blind Spot Intervention (I-BSI)”
30.  Unavailable High Cabin Temperature (if so equipped)
    This warning appears if the interior temperature of the vehicle has reached such a high temperature that the sensor for the Traffic Sign Recognition (TSR) system can no longer function reliably. Once the interior temperature has reached normal levels, the warning should disappear. If the warning continues to display, have the system checked. It is recommended that you visit a NISSAN dealer for this service.
    For additional information, refer to “Traffic Sign Recognition (TSR)”.
31. Unavailable Side Radar Obstruction (if so equipped)
    This message appears when the Blind Spot Warning (BSW)/Intelligent Blind Spot Intervention (I-BSI)/Rear Cross Traffic Alert (RCTA)/Intelligent Back-up Intervention (I-BI) systems become unavailable because a radar blockage is detected. For additional information, refer to “Blind Spot Warning (BSW)” “Intelligent Blind Spot Intervention (I-BSI “Rear Cross Traffic Alert (RCTA)”or “Intelligent Back-up Intervention (I-BI)”.
32.  Unavailable: High Accelerator Temperature
    This message appears when the Intelligent Back-up Intervention (I-BI) system becomes unavailable because of an interior temperature greater than approximately 104°F (40°C). For additional information, refer to “Intelligent Back-up Intervention (I-BI)”.
33.  Forward Driving Aids temporarily disabled Front Sensor blocked warning
    This message appears when the sensor area of the front bumper is covered with dirt or is obstructed, making it impossible to detect a vehicle ahead.
    The following systems will be automatically canceled.
    • Intelligent Cruise Control (ICC) system (if so equipped)
    • Automatic Emergency Braking (AEB) with the pedestrian detection system
    • Intelligent Forward Collision Warning
      (I-FCW)
      For more details, see “Intelligent Cruise Control (ICC)”, “Automatic Emergency Braking (AEB) with pedestrian detection system” or “Intelligent Forward Collision Warning (I-FCW)”.
34. shipping Mode On Push Storage
    Fuse (if so equipped)
    This warning may appear if the extended storage fuse switch is not pushed in (switched on). When this warning appears, push in (switch on) the extended storage fuse switch to turn off the warning.
35.  Headlight System Error
    This warning appears if the LED headlights are malfunctioning. It is recommended you have the system checked by a NISSAN dealer.
36.  Intelligent Lane Intervention (I-LI)/Intelligent Blind Spot Intervention (I-BSI) ON indicator
    This indicator appears when one or more of the following systems is activated.
    • Intelligent Lane Intervention (I-LI)
    •  Intelligent Blind Spot Intervention (I-BSI)
      For more details, see “Intelligent Lane Intervention (I-LI)” or “Intelligent Blind Spot Intervention (I-BSI)”
37. Not Available: Poor Road Conditions (if so equipped)
    This warning may appear when the Intelligent Blind Spot Intervention (I-BSI), the Intelligent Lane Intervention (I-LI) or the Intelligent Cruise Control (ICC) system is engaged.
    Under the following conditions, the I-BSI, I-LI or ICC system is automatically canceled:
    • When the Vehicle Dynamic Control (VDC) or ABS operates
    • When a wheel slips
      The above system cannot be used in some situations. (VDC operates and a wheel slips.) 39-40. Currently unavailable/Currently not available (if so equipped)
      This message appears and the Intelligent Blind Spot Intervention (I-BSI) system, the Intelligent Lane Intervention (I-LI) system and Intelligent Cruise Control (ICC) system will be turned off automatically under the following conditions:
    • When the VDC system is turned off. When the SNOW mode is selected.
    • When the 4WD shift switch is in the 4H or 4L position. (4WD models).
      “Vehicle Dynamic Control (VDC) system”, “SNOW mode” , “NISSAN all-mode 4WD®”, “Intelligent Blind Spot Intervention (I-BSI)”, “Intelligent Lane Intervention (I-LI)” and “Intelligent Cruise Control (ICC)”
38.  Automatic Transmission (AT)
    position indicator
    This indicator shows the transmission shift position.
39.  Rear Door Alert is activated
    When the system is enabled, this message appears when the Rear Door Alert system is active and can remind the driver to check the rear seat.
    • Using the steering switch, the driver
      can select “Dismiss Message” to clear the display for a period of time.
    • Using the steering switch, the driver can select “Disable Alert” to disable the horn alert for the remainder of the current trip.
      WARNING
      Selecting “Dismiss Message” during a stop within a trip temporarily dis-misses the message for that stop without turning the system off.
      Alerts can be provided for other stops during the trip. Selecting “Disable Alert” turns off the Rear Door Alert system for the remainder of a trip and no audible alert will be provided.
      NOTE:
      This system is disabled until the driver enables it using the settings menu.
40. Check Rear Seat for all articles
    When the rear door alert system is enabled, this message appears when the vehicle comes to a complete stop, the shift lever is moved from the D (Drive) or R (Reverse) position to P (Park) position, and the driver exits the vehicle. This message alerts the driver, after a period of time, to check for items in the rear seat after the audible alert has been provided.
    NOTE:
    This rear door alert system is disabled until a driver enables it using the rear door alert switch.
41. Rear Seat Belt warning
    This rear seat belt warning appears after the ignition switch is pushed to the ON position. If any of the rear passenger’s seat belts is not fastened, the seat icon illuminates in red to show which seat belt is not fastened. The seat icon illuminates in red until the corresponding rear passenger’s seat belt is fastened. The warning will automatically turn off after approximately 65 seconds. If so equipped, the seat icon will turn gray (or green, depending on the models) if the seat is occupied and the passenger is buckled. If a rear passenger seat belt is fastened and then unfastened at a vehicle speed less than approximately 10 MPH (15 km/h), the seat icon will illuminate. When the vehicle speed exceeds approximately 10 MPH (15 km/h), the seat icon will blink and the chime will sound. The warning will turn off when a rear passenger seat belt is fastened or automatically turn off approximately 65 seconds after the seat belt is unfastened. For precautions on seat belt usage, see “Seat belts”. The display of the rear seat belt warning varies depending on the number of seats.
42. Malfunction See Owner’s Manual (if so equipped)
    This warning appears when the Traffic Sign Recognition (TSR) system malfunctions.
43. System fault See Owner’s Manual
    This warning appears when the Rear Automatic Braking (RAB) system malfunctions.
44. Take a Break? indicator
    This indicator appears when the Intelli-gent Driver Alertness (I-DA) system detect that the driver attention is decreasing.
45. Intelligent Driver Alertness (I-DA)malfunction
    This warning appears when the Intelligent Driver Alertness (I-DA) system malfunctions.

TRIP COMPUTER

The trip computer switch is located on the left side of the steering wheel. To operate the trip computer, push the switch.
Each time the left or right side of the button is pushed, the display will change.

1.  Home
   The Home mode shows the following information.
   • Vehicle speed
   • Navigation (if so equipped)
   • Audio
2.  Audio
   The audio mode shows the status of audio information.
   For more details, see NissanConnect® Owner’s Manual.
3.  Compass
   This display indicates the heading direction of the vehicle.
4. Navigation
   When the route guidance is set in the navigation system, this item shows the navigation route information.
   For more details, see NissanConnect® Owner’s Manual.
5. Vehicle speed (MPH or km/h)
   The vehicle speed mode shows the current vehicle speed and the average vehicle speed since the last reset.
   Resetting is done by pushing the left or right side of the button for longer than 1 second.
   Average vehicle speed:
   The average vehicle speed display is updated every 30 seconds. The first 30 seconds after a reset, the display shows “———”.
6. Elapsed time and trip ram promaster odometer (mile or km)
   Elapsed time:
   The elapsed time mode shows the time since the last reset. The displayed time can be reset by pushing the left or right side of the button for longer than 1 second. (The trip odometer is also reset at the same time.)
   Trip odometer:
   The trip odometer mode shows the total distance the vehicle has been driven since the last reset. Resetting is done by pushing the left or right side of the
   button for longer than 1 second. (The elapsed time is also reset at the same time.)
7. Current fuel consumption and
   average fuel consumption (MPG, l (liter)/100 km or km/l)
   Current fuel consumption:
   The current fuel consumption mode shows the current fuel consumption.
   Average fuel consumption:
   The average fuel consumption mode shows the average fuel consumption since the last reset. Resetting is done by pushing the left or right side of the button for longer than 1 second.
   The display is updated every 30 seconds. At about the first 1/3 mile (500 m) after a reset, the display shows “——”.
8.  Intelligent Cruise Control (ICC) system
   This mode shows the operating condition for the Intelligent Cruise Control (ICC) system.
   NOTE:
   If the ICC system is in a standby state, this screen is automatically displayed.
9. Driving aids (if so equipped)
   The driving aids mode shows the operating condition for the following systems if the vehicle is equipped with them.
   • Automatic Emergency Braking (AEB) with the pedestrian detection system
   • Intelligent Forward Collision Warning (I-FCW)
   • Lane Departure Warning (LDW)
   • Intelligent Lane Intervention (I-LI)
   • Blind Spot Warning (BSW)
   • Intelligent Blind Spot Intervention (I- BSI)
   • For more details, see “Automatic Emergency Braking (AEB) with Pedestrian Detection System” , “Intelligent
   • Forward Collision Warning (I-FCW)”, “Lane Departure Warning (LDW)”, “Intelligent Lane Intervention (I-LI)” , “Blind Spot Warning (BSW)” or “Intelligent Blind Spot Intervention (I-BSI)”
10. Tire pressures
    The tire pressure mode shows the pressure of all four tires while the vehicle is driven.
    When the “Tire Pressure Low Add Air” warning appears, the display can be switched to the tire pressure mode by pushing the left or right side of the button.
    The tire pressure unit can be changed using the “TPMS Setting” menu displayed in the vehicle information display.
    NOTE:
    After the ignition switch is placed in the ON position, it may take a period of time for the tire pressure to be displayed while the vehicle is driven. Depending on the radio wave circumstance, tire pressure may not correctly be displayed.
    
11. Auxiliary gauges
    The auxiliary gauges consist of the battery voltage gauge and the engine oil pressure gauge.
    1. The engine oil pressure gauge indicates the current engine oil pressure.
    2. The battery voltage gauge indicates current battery voltage.

CLOCK AND OUTSIDE AIR TEMPERATURE

The clock and outside air temperature is displayed on the upper side of the vehicle information display.

Outside air temperature (°F or °C)
The outside air temperature is displayed in °F or °C in the range of −40 to 140°F (−40 to 60°C).
The outside temperature sensor is located in front of the radiator. The sensor may be affected by road or engine heat, wind directions and other driving conditions. The display may differ from the actual outside temperature or the temperature displayed on various signs or billboards.

FAQ